REAR NO. 1 SEAT OUTER BELT ASSEMBLY > REMOVAL |
| 1. REMOVE REAR CENTER SEAT ASSEMBLY (for LH Side) |
| 2. REMOVE REAR SEAT HEADREST ASSEMBLY |
![]() |
Press the headrest support button and pull up the headrest to its highest position as shown in the illustration.
![]() |
Insert a finger or screwdriver into the hole to release the lock. Pull the headrest up as shown in the illustration to remove it.
| 3. REMOVE REAR SEAT TRACK BRACKET COVER |
![]() |
Disengage the 8 claws and remove the 2 rear seat track bracket covers.
| 4. REMOVE REAR OUTER TRACK BRACKET COVER |
![]() |
Disengage the 4 claws and remove the rear outer track bracket cover.
| 5. REMOVE REAR INNER TRACK BRACKET COVER |
![]() |
Disengage the 5 claws and remove the rear inner track bracket cover.
| 6. REMOVE RECLINING HINGE COVER LH (for LH Side) |
![]() |
Disengage the 2 clips and remove the reclining hinge cover LH.
| 7. REMOVE REAR SEAT LEG SIDE COVER LH (for LH Side) |
![]() |
Disengage the 3 claws and remove the rear seat leg side cover.
| 8. REMOVE REAR SEAT LEG SIDE COVER RH (for RH Side) |
![]() |
Disengage the 3 claws.
Disengage the clip and remove the rear seat leg side cover.
| 9. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY (w/ Remote Folding Function) |
Pull down the adjuster's lock piece to release the lock as shown in the illustration.

![]() |
Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.
Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.
Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.
| 10. REMOVE REAR NO. 1 SEAT ASSEMBLY |
![]() |
Remove the 3 bolts on the rear side of the seat.
![]() |
Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.
| 11. REMOVE REAR DOOR SCUFF PLATE |
![]() |
Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.
| 12. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP |
| 13. REMOVE DECK BOARD ASSEMBLY |
![]() |
Remove the deck board assembly.
| 14. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY |
![]() |
Disengage the 2 guides and remove the No. 3 deck board sub-assembly.
| 15. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY |
![]() |
Disengage the 2 guides and remove the No. 2 deck board sub-assembly.
| 16. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Remove the tonneau cover assembly.
| 17. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat) |
![]() |
Disengage the 3 clips and the 3 guides, and remove the rear No. 1 floor board.
| 18. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat) |
![]() |
Disengage the 2 clips and remove the rear seat side cover LH.
| 19. REMOVE DECK SIDE TRIM BOX LH |
![]() |
Remove the 2 deck side trim clips and clip.
Remove the deck side trim box LH as shown in the illustration.

| 20. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat) |
![]() |
Disengage the 2 clips and remove the rear seat side cover RH.
| 21. REMOVE JACK CARRIER SUPPORT |
| 22. REMOVE JACK CARRIER CUSHION |
![]() |
Remove the jack carrier cushion.
| 23. REMOVE JACK ASSEMBLY |
![]() |
Remove the jack assembly.
| 24. REMOVE JACK CARRIER ASSEMBLY |
![]() |
Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.
| 25. REMOVE DECK SIDE TRIM BOX RH |
![]() |
Remove the 2 deck side trim clips and clip.
Remove the deck side trim box RH as shown in the illustration.

| 26. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat) |
![]() |
Remove the 4 bolts and 4 nuts.
Remove the deck floor board assembly.
| 27. REMOVE REAR MAT |
![]() |
Remove the rear mat.
| 28. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat) |
![]() |
Disengage the 3 claws.
Remove the 2 nuts and the deck floor board assembly.
| 29. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat) |
![]() |
Remove the 2 nuts and the deck floor box.
| 30. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat) |
![]() |
Remove the bolt and rear No. 2 seat inner belt assembly.
| 31. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat) |
![]() |
Remove the bolt and disconnect the rear seat lap type belt assembly LH.
| 32. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat) |
| 33. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat) |
![]() |
Remove the 4 bolts and the rear No. 2 seat assembly.
| 34. REMOVE REAR FLOOR FINISH PLATE |
![]() |
Disengage the 4 clips and the 4 claws, and remove the rear floor finish plate.
| 35. REMOVE REAR SEAT SIDE GARNISH CAP (for RH Side without Rear Air Conditioning System) |
![]() |
Disengage the 8 claws and guide, and remove the rear seat side garnish cap.
| 36. REMOVE REAR SEAT SIDE GARNISH CAP (for RH Side with Rear Air Conditioning System) |
![]() |
Remove the screw.
Disengage the 6 claws and the guide, and remove the rear seat side garnish cap.
| 37. REMOVE DECK SIDE TRIM COVER |
![]() |
Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.
| 38. REMOVE DECK SIDE TRIM |
![]() |
Remove the bolt.
![]() |
Disengage the 4 claws and the 3 guides, and remove the deck side trim LH as shown in the illustration.
| 39. REMOVE SIDE TRIM COVER LH (for LH Side without Rear Seat Entertainment System) |
![]() |
Disengage the 10 claws and remove the side trim cover LH.
| 40. REMOVE POWER OUTLET SOCKET BEZEL (for LH Side with Rear Seat Entertainment System) |
![]() |
Disengage the 4 claws.
![]() |
Disconnect each connector and remove the power outlet socket bezel.
| 41. REMOVE SIDE TRIM COVER RH (for RH Side without Rear Automatic Air Conditioning System) |
![]() |
Disengage the 4 claws and remove the side trim cover RH.
| 42. REMOVE REAR ROOM TEMPERATURE SENSOR (for RH Side with Rear Automatic Air Conditioning System) |
![]() |
Disengage the 4 claws and remove the rear room temperature sensor.
Disconnect the connector.
| 43. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH (for LH Side) |
![]() |
Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.
| 44. REMOVE REAR COMBINATION LIGHT SERVICE COVER RH (for RH Side) |
![]() |
Using a screwdriver, disengage the 6 claws and the 2 guides, and remove the rear combination light service cover RH.
| 45. REMOVE REAR POWER POINT SOCKET ASSEMBLY (for LH Side) |
Disconnect the connector.
![]() |
Disengage the claw and remove the rear power point socket assembly.
| 46. REMOVE REAR POWER OUTLET SOCKET COVER (for LH Side) |
![]() |
Disengage the 2 claws and remove the rear power outlet socket cover.
| 47. REMOVE REAR DECK TRIM COVER (for LH Side without Remote Folding Function) |
![]() |
Disengage the 10 claws and remove the rear deck trim cover.
| 48. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (for LH Side with Remote Folding Function) |
![]() |
Disengage the 5 claws and remove the reclining remote control lever bezel LH.
| 49. REMOVE ROPE HOOK ASSEMBLY |
![]() |
for Front Side:
Using a screwdriver, disengage the 2 claws.
Remove the bolt and the rope hook assembly.
![]() |
for Rear Side:
Using a screwdriver, disengage the 2 claws.
Remove the bolt and rope hook assembly.
| 50. REMOVE NO. 2 DECK SIDE TRIM HOOK (for LH Side) |
![]() |
Remove the screw and the No. 2 deck side trim hook.
| 51. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side) |
| 52. REMOVE FRONT DECK SIDE TRIM COVER |
![]() |
Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.
| 53. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY |
![]() |
Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.
| 54. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side) |
Remove the 2 bolts.
Remove the 2 clips.
Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.

| 55. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side) |
Remove the 3 bolts.
Remove the 2 clips.
Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly RH.

| 56. REMOVE QUARTER PILLAR GARNISH |
![]() |
Disengage the 2 claws and 2 guides, and remove the No. 1 seat outer belt guide.
![]() |
Disengage the 2 clips and the 2 guides, and remove the quarter pillar garnish LH.
| 57. REMOVE REAR NO. 1 SEAT OUTER BELT ASSEMBLY |
![]() |
Remove the bolt and disconnect the shoulder anchor of the rear No. 1 seat outer belt assembly.
![]() |
Remove the 2 bolts and rear No. 1 seat outer belt assembly.