REAR CENTER SEAT INNER BELT ASSEMBLY > INSTALLATION |
| 1. INSTALL REAR CENTER SEAT INNER BELT ASSEMBLY |
![]() |
Install the rear center seat inner belt assembly with the bolt.
| 2. INSTALL REAR NO. 1 SEAT ASSEMBLY LH |
![]() |
Temporarily install the 2 bolts on the front side of the seat.
![]() |
Temporarily install the 3 bolts on the rear side of the seat.
Install the rear No. 1 seat assembly with the 5 bolts.
| 3. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function) |
Remove the rear seat reclining control cable from the carpet hole.

Connect the rear seat reclining control cable as shown in the illustration.
Connect the rear No. 1 seat lock cable assembly as shown in the illustration.

![]() |
Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.
Return the seatback to the upright position.
Pull up the adjuster's lock piece to lock it as shown in the illustration.

| 4. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for LH Side) |
Check that the left and right adjusters lock simultaneously when sliding the seat.
If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.
| 5. INSTALL REAR SEAT LEG SIDE COVER LH |
![]() |
Engage the 3 claws and install the rear seat leg side cover.
| 6. INSTALL RECLINING HINGE COVER LH |
![]() |
Engage the 2 clips and install the reclining hinge cover LH.
| 7. INSTALL REAR INNER TRACK BRACKET COVER LH |
![]() |
Engage the 5 claws and install the rear inner track bracket cover.
| 8. INSTALL REAR OUTER TRACK BRACKET COVER LH |
![]() |
Engage the 4 claws and install the rear outer track bracket cover.
| 9. INSTALL REAR SEAT TRACK BRACKET COVER LH |
![]() |
Engage the 8 claws and install the 2 rear seat track bracket covers.
| 10. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side) |
![]() |
Install the rear seat headrest assembly as shown in the illustration.
| 11. INSTALL REAR CENTER SEAT ASSEMBLY |
| 12. INSTALL REAR NO. 1 SEAT ASSEMBLY RH |
![]() |
Temporarily install the 2 bolts on the front side of the seat.
![]() |
Temporarily install the 3 bolts on the rear side of the seat.
Install the rear No. 1 seat assembly with the 5 bolts.
| 13. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function) |
Remove the rear seat reclining control cable from the carpet hole.

Connect the rear seat reclining control cable as shown in the illustration.
Connect the rear No. 1 seat lock cable assembly as shown in the illustration.

![]() |
Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.
Return the seatback to the upright position.
Pull up the adjuster's lock piece to lock it as shown in the illustration.

| 14. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for RH Side) |
Check that the left and right adjusters lock simultaneously when sliding the seat.
If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.
| 15. INSTALL REAR SEAT LEG SIDE COVER RH |
![]() |
Engage the clip.
Engage the 3 claws and install the rear seat leg side cover.
| 16. INSTALL REAR INNER TRACK BRACKET COVER RH |
![]() |
Engage the 5 claws and install the rear inner track bracket cover.
| 17. INSTALL REAR OUTER TRACK BRACKET COVER RH |
![]() |
Engage the 4 claws and install the rear outer track bracket cover.
| 18. INSTALL REAR SEAT TRACK BRACKET COVER RH |
![]() |
Engage the 8 claws and install the 2 seat track bracket covers.
| 19. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side) |
![]() |
Install the rear seat headrest assembly as shown in the illustration.