Home › BODY ELECTRICAL › DOOR LOCK › ELECTRICAL KEY OSCILLATOR (for Rear Side)

ELECTRICAL KEY OSCILLATOR (for Rear Side) > INSTALLATION

for Preparation Click here



1. INSTALL INDOOR ELECTRICAL KEY OSCILLATOR


    B176964
  1. Install the indoor electrical key oscillator with the clamp.

  1. Connect the connector.



    A171920
  1. Install the front floor carpet with the 3 clips.



2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Engage the 4 clips and the 7 claws.

  1. Install the 2 clips.



  1. Install the deck trim side panel assembly LH with the 2 bolts.


    B173613



3. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH


    B170934E01
  1. Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding part of the floor panel.



4. INSTALL FRONT DECK SIDE TRIM COVER LH


    B175145
  1. Engage the 4 claws and install the 2 front deck side trim covers LH.



5. INSTALL NO. 2 DECK SIDE TRIM HOOK


    B173612
  1. Install the No. 2 deck side trim hook with the screw.



6. INSTALL ROPE HOOK ASSEMBLY (for LH Side)


    B173599
  1. for Front Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.



    B173601
  1. for Rear Side:

    1. Install the rope hook assembly with the bolt.

      Torque:
      6.5 N*m{ 66 kgf*cm , 58 in.*lbf }

    2. Engage the 2 claws.



7. INSTALL REAR DECK SIDE TRIM COVER (w/o Remote Folding Function)


    B173602
  1. Engage the 10 claws and install the rear deck trim cover.



8. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)


    B173603
  1. Engage the 5 claws and install the reclining remote control bezel lever LH.



9. INSTALL REAR POWER OUTLET SOCKET COVER


    E151328
  1. Engage the 2 claws and install the rear power outlet socket cover.



10. INSTALL REAR POWER POINT SOCKET ASSEMBLY


    E151490
  1. Engage the claw and install the rear power point socket assembly.

  1. Connect the connector.



11. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH


    B175146
  1. Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.



12. INSTALL SIDE TRIM COVER LH (w/o Rear Seat Entertainment System)


    B173597
  1. Engage the 10 claws and install the side trim cover LH.



13. INSTALL POWER OUTLET SOCKET BEZEL (w/ Rear Seat Entertainment System)


    B173681
  1. Connect each connector.



    B173680
  1. Engage the 4 claws and install the power outlet socket bezel.



14. INSTALL DECK SIDE TRIM LH


    B173624
  1. Engage the 3 guides and 4 claws as shown in the illustration.



    B173596
  1. Install the deck side trim LH with the bolt.



15. INSTALL DECK SIDE TRIM COVER LH


    B175144
  1. Engage the 2 claws and install the deck side trim cover LH.



16. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
  1. Engage the 4 clips and the 7 claws.

  1. Install the 2 clips.



  1. Install the deck trim side panel assembly RH with the 3 bolts.


    B173622



17. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side.



18. INSTALL FRONT DECK SIDE TRIM COVER RH

HINT:
Use the same procedure for the RH side and the LH side.



19. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM

HINT:
Use the same procedure for the No. 1 luggage compartment trim hook and the No. 2 deck side trim hook.



20. INSTALL ROPE HOOK ASSEMBLY (for RH Side)

HINT:
Use the same procedure for the RH side and the LH side.



21. INSTALL REAR COMBINATION LIGHT SERVICE COVER RH


    B173619
  1. Engage the 2 guides and 6 claws, and install the rear combination light service cover RH.



22. INSTALL REAR ROOM TEMPERATURE SENSOR (w/ Automatic Air Conditioning System)
  1. Connect the connector.



    E150364
  1. Engage the 4 claws and install the rear room temperature sensor.



23. INSTALL SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)


    B173610
  1. Engage the 4 claws, and install the side trim cover RH.



24. INSTALL DECK SIDE TRIM RH

HINT:
Use the same procedure for the RH side and the LH side.



25. INSTALL DECK SIDE TRIM COVER RH

HINT:
Use the same procedure for the RH side and the LH side.



26. INSTALL REAR SEAT SIDE GARNISH CAP (w/o Rear Air Conditioning System)


    B173615
  1. Engage the guide and the 8 claws, and install the rear seat side garnish cap.



27. INSTALL REAR SEAT SIDE GARNISH CAP (w/ Rear Air Conditioning System)


    B173617
  1. Engage the guide and the 6 claws.

  1. Install the rear seat side garnish cap with the screw.



28. INSTALL REAR FLOOR FINISH PLATE


    B173609
  1. Engage the 4 clips and the 4 claws, and install the rear floor finish plate.



29. INSTALL REAR NO. 2 SEAT ASSEMBLY


    B173781
  1. Install the rear No. 2 seat assembly with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



30. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH


    B170936
  1. Install the rear seat lap type belt assembly LH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.



31. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH
  1. Install the rear seat lap type belt assembly RH with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    After installing the belt, check that it is not twisted.



32. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY


    B170935
  1. Install the rear No. 2 seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 2 seat inner belt assembly to overlap the protruding part of the rear No. 2 seat bracket.

    HINT:
    Use the same procedure for the RH side and LH side.



33. INSTALL REAR MAT


    B173249
  1. Install the rear mat.



34. INSTALL DECK FLOOR BOARD ASSEMBLY


    B178561
  1. Install the 2 nuts and the deck floor board assembly.

  1. Engage the 3 claws.



35. INSTALL DECK SIDE TRIM BOX LH


  1. Install the deck side trim box LH as shown in the illustration.


    B178555



    B173243E01
  1. Install the 2 deck side trim clip and the clips.



36. INSTALL REAR SEAT SIDE COVER LH


    B173607
  1. Engage the 2 clips and install the rear seat side cover LH.



37. INSTALL DECK SIDE TRIM BOX RH


  1. Install the deck side trim box RH as shown in the illustration.


    B178553



    B173247E01
  1. Install the 2 deck side trim clip and the clips.



38. INSTALL JACK CARRIER ASSEMBLY


    B178549
  1. Engage the 3 claws, and install the jack carrier assembly.



39. INSTALL JACK ASSEMBLY


    B173245
  1. Install the jack assembly.



40. INSTALL JACK CARRIER CUSHION


    B178550
  1. Install the jack carrier cushion.



41. INSTALL JACK CARRIER SUPPORT


42. INSTALL REAR SEAT SIDE COVER RH


    B173608
  1. Engage the 2 clips and install the rear seat side cover RH.



43. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


44. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY


    B173244
  1. Engage the 2 guides and install the No. 2 deck board sub-assembly.



45. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY


    B173242
  1. Engage the 2 guides and install the No. 3 deck board sub-assembly.



46. INSTALL DECK BOARD ASSEMBLY


    B173240
  1. Install the deck board assembly.



47. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH


    B173233E01
  1. Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

    NOTICE:
    After installation, check that the corners fit correctly.



48. INSTALL REAR DOOR SCUFF PLATE LH


    B173228
  1. Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.



49. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    B173237E01
  1. Align the alignment mark (green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

    NOTICE:
    After installation, check that the corners fit correctly.



50. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side.



51. INSTALL REAR NO. 1 SEAT ASSEMBLY LH


    B173778
  1. Temporarily install the 2 bolts on the front side of the seat.



    B173780
  1. Temporarily install the 3 bolts on the rear side of the seat.

  1. Install the rear No. 1 seat assembly with the 5 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



52. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)


  1. Remove the rear seat reclining control cable from the carpet hole.


    B180395E01

  1. Connect the rear seat reclining control cable as shown in the illustration.



  1. Connect the rear No. 1 seat lock cable assembly as shown in the illustration.


    B173771E01



    B174591
  1. Engage the 2 claws and connect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Return the seatback to the upright position.



  1. Pull up the adjuster's lock piece to lock it as shown in the illustration.


    B180389E01

    NOTICE:
    When pressing the lock piece, make sure the adjuster's spring is not compress.



53. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for LH Side)
  1. Check that the left and right adjusters lock simultaneously when sliding the seat.

  1. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.



54. INSTALL REAR SEAT LEG SIDE COVER LH


    B181544
  1. Engage the 3 claws and install the rear seat leg side cover.



55. INSTALL REAR INNER TRACK BRACKET COVER LH


    B181542
  1. Engage the 5 claws and install the rear inner track bracket cover.



56. INSTALL REAR OUTER TRACK BRACKET COVER LH


    B173776
  1. Engage the 4 claws and install the rear outer track bracket cover.



57. INSTALL SEAT TRACK BRACKET COVER LH


    B173775
  1. Engage the 8 claws and install the 2 rear seat track bracket covers.



58. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)


    B176351
  1. Install the rear seat headrest assembly as shown in the illustration.



59. INSTALL REAR CENTER SEAT ASSEMBLY


60. INSTALL REAR NO. 1 SEAT ASSEMBLY RH


61. CONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)

HINT:
Use the same procedure for the RH side and the LH side.



62. INSPECT REAR SEAT SLIDE ADJUSTER LOCK (for RH Side)
  1. Check that the left and right adjusters lock simultaneously when sliding the seat.

  1. If the left and right adjusters do not lock simultaneously, adjust by loosening the bolts securing the seat.



63. INSTALL REAR SEAT LEG SIDE COVER RH


    B173765
  1. Engage the clip.

  1. Engage the 3 claws and install the rear seat leg side cover.



64. INSTALL RECLINING HINGE COVER LH


    B181543
  1. Engage the 2 clips and install the reclining hinge cover LH.



65. INSTALL REAR INNER TRACK BRACKET COVER RH


    B181546
  1. Engage the 5 claws and install the rear inner track bracket cover.



66. INSTALL REAR OUTER TRACK BRACKET COVER RH


    B173763
  1. Engage the 4 claws and install the rear outer track bracket cover.



67. INSTALL SEAT TRACK BRACKET COVER RH


    B173760
  1. Engage the 8 claws and install the 2 seat track bracket covers.



68. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)


    B176352
  1. Install the rear seat headrest assembly as shown in the illustration.