VANITY LIGHT > REMOVAL |
| 1. REMOVE REAR CENTER SEAT ASSEMBLY |
| 2. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side) |
| 3. REMOVE REAR SEAT TRACK BRACKET COVER LH |
![]() |
Disengage the 8 claws and remove the 2 rear seat track bracket covers.
| 4. REMOVE REAR OUTER TRACK BRACKET COVER LH |
![]() |
Disengage the 4 claws and remove the rear outer track bracket cover.
| 5. REMOVE REAR INNER TRACK BRACKET COVER LH |
![]() |
Disengage the 5 claws and remove the rear inner track bracket cover.
| 6. REMOVE RECLINING HINGE COVER LH |
![]() |
Disengage the 2 clips and remove the reclining hinge cover LH.
| 7. REMOVE REAR SEAT LEG SIDE COVER LH |
![]() |
Disengage the 3 claws and remove the rear seat leg side cover.
| 8. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function) |
Pull down the adjuster's lock piece to release the lock as shown in the illustration.

![]() |
Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.
Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.
Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.
| 9. REMOVE REAR NO. 1 SEAT ASSEMBLY LH |
![]() |
Remove the 3 bolts on the rear side of the seat.
![]() |
Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.
| 10. REMOVE REAR SEAT HEADREST ASSEMBLY (for RH Side) |
| 11. REMOVE REAR SEAT TRACK BRACKET COVER RH |
![]() |
Disengage the 8 claws and remove the 2 rear seat track bracket covers.
| 12. REMOVE REAR INNER TRACK BRACKET COVER RH |
![]() |
Disengage the 5 claws and remove the rear inner track bracket cover.
| 13. REMOVE REAR OUTER TRACK BRACKET COVER RH |
![]() |
Disengage the 4 claws and remove the rear outer track bracket cover.
| 14. REMOVE REAR SEAT LEG SIDE COVER RH |
![]() |
Disengage the 3 claws.
Disengage the clip and remove the rear seat leg side cover.
| 15. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function) |
| 16. REMOVE REAR NO. 1 SEAT ASSEMBLY RH |
![]() |
Remove the 3 bolts on the rear side of the seat.
![]() |
Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.
| 17. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Disengage the 8 claws and guide, and remove the front door scuff plate LH.
| 18. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Remove the clip.
Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.
| 19. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Remove the front door opening trim weatherstrip LH.
| 20. REMOVE FRONT PILLAR GARNISH LH |
![]() |
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 3 guides and remove the front pillar garnish LH.
Remove the clip <A>.
![]() |
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
| 21. REMOVE REAR DOOR SCUFF PLATE LH |
![]() |
Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.
| 22. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Remove the rear door opening trim weatherstrip LH.
| 23. REMOVE LOWER CENTER PILLAR GARNISH LH |
![]() |
Disengage the 2 claws and 2 clips, and remove the lower center pillar garnish LH.
| 24. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH |
![]() |
Remove the bolt and disconnect the floor end of the front seat outer belt assembly.
| 25. REMOVE CENTER PILLAR GARNISH LH |
![]() |
Remove the screw and clip.
Disengage the 2 guides and clip, and remove the center pillar garnish LH.
| 26. REMOVE FRONT DOOR SCUFF PLATE RH |
| 27. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH |
| 28. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
| 29. REMOVE FRONT PILLAR GARNISH RH |
![]() |
Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.
Cut off the clip <A>.
Disengage the 3 guides and remove the front pillar garnish RH.
Remove the clip <A>.
![]() |
Protect the curtain shield airbag assembly.
Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.
| 30. REMOVE REAR DOOR SCUFF PLATE RH |
| 31. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH |
| 32. REMOVE LOWER CENTER PILLAR GARNISH RH |
| 33. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH |
| 34. REMOVE CENTER PILLAR GARNISH RH |
| 35. REMOVE DECK BOARD ASSEMBLY |
![]() |
Remove the deck board assembly.
| 36. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY |
![]() |
Disengage the 2 guides and remove the No. 3 deck board sub-assembly.
| 37. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY |
![]() |
Disengage the 2 guides and remove the No. 2 deck board sub-assembly.
| 38. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Remove the tonneau cover assembly.
| 39. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat) |
![]() |
Disengage the 3 clips and the 3 guides, and remove the rear No. 1 floor board.
| 40. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat) |
![]() |
Disengage the 2 clips and remove the rear seat side cover LH.
| 41. REMOVE DECK SIDE TRIM BOX LH |
![]() |
Remove the 2 deck side trim clips and clip.
Remove the deck side trim box LH as shown in the illustration.

| 42. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat) |
![]() |
Disengage the 2 clips and remove the rear seat side cover RH.
| 43. REMOVE JACK CARRIER SUPPORT |
| 44. REMOVE JACK CARRIER CUSHION |
![]() |
Remove the jack carrier cushion.
| 45. REMOVE JACK ASSEMBLY |
![]() |
Remove the jack assembly.
| 46. REMOVE JACK CARRIER ASSEMBLY |
![]() |
Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.
| 47. REMOVE DECK SIDE TRIM BOX RH |
![]() |
Remove the 2 deck side trim clips and clip.
Remove the deck side trim box RH as shown in the illustration.

| 48. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat) |
![]() |
Remove the 4 bolts and 4 nuts.
Remove the deck floor board assembly.
| 49. REMOVE REAR MAT |
![]() |
Remove the rear mat.
| 50. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat) |
![]() |
Disengage the 3 claws.
Remove the 2 nuts and the deck floor board assembly.
| 51. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat) |
![]() |
Remove the 2 nuts and the deck floor box.
| 52. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat) |
![]() |
Remove the bolt and rear No. 2 seat inner belt assembly.
| 53. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat) |
![]() |
Remove the bolt and disconnect the rear seat lap type belt assembly LH.
| 54. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat) |
| 55. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat) |
![]() |
Remove the 4 bolts and the rear No. 2 seat assembly.
| 56. REMOVE REAR FLOOR FINISH PLATE |
![]() |
Disengage the 4 clips and the 4 claws, and remove the rear floor finish plate.
| 57. REMOVE DECK SIDE TRIM COVER LH |
![]() |
Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.
| 58. REMOVE DECK SIDE TRIM LH |
![]() |
Remove the bolt.
![]() |
Disengage the 4 claws and the 3 guides, and remove the deck side trim LH as shown in the illustration.
| 59. REMOVE SIDE TRIM COVER LH (w/o Rear Seat Entertainment System) |
![]() |
Disengage the 10 claws and remove the side trim cover LH.
| 60. REMOVE POWER OUTLET SOCKET BEZEL (w/ Rear Seat Entertainment System) |
![]() |
Disengage the 4 claws.
![]() |
Disconnect each connector and remove the power outlet socket bezel.
| 61. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH |
![]() |
Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.
| 62. REMOVE REAR POWER POINT SOCKET ASSEMBLY |
Disconnect the connector.
![]() |
Disengage the claw and remove the rear power point socket assembly.
| 63. REMOVE REAR POWER OUTLET SOCKET COVER |
![]() |
Disengage the 2 claws and remove the rear power outlet socket cover.
| 64. REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function) |
![]() |
Disengage the 10 claws and remove the rear deck trim cover.
| 65. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function) |
![]() |
Disengage the 5 claws and remove the reclining remote control lever bezel LH.
| 66. REMOVE ROPE HOOK ASSEMBLY (for LH Side) |
![]() |
for Front Side:
Using a screwdriver, disengage the 2 claws.
Remove the bolt and the rope hook assembly.
![]() |
for Rear Side:
Using a screwdriver, disengage the 2 claws.
Remove the bolt and rope hook assembly.
| 67. REMOVE NO. 2 DECK SIDE TRIM HOOK |
![]() |
Remove the screw and the No. 2 deck side trim hook.
| 68. REMOVE FRONT DECK SIDE TRIM COVER LH |
![]() |
Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.
| 69. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH |
![]() |
Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.
| 70. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH |
Remove the 2 bolts.
Remove the 2 clips.
Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.

| 71. REMOVE QUARTER PILLAR GARNISH LH |
![]() |
Disengage the 2 claws and 2 guides, and remove the No. 1 seat outer belt guide.
![]() |
Disengage the 2 clips and the 2 guides, and remove the quarter pillar garnish LH.
| 72. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH (w/o Power Back Door) |
w/o Rear No. 2 Seat:
![]() |
Remove the bolt.
Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.
w/ Rear No. 2 Seat:
![]() |
Disengage the 2 claws and 2 guides, and remove the rear No. 2 seat outer belt guide.
![]() |
Remove the bolt.
Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.
| 73. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH (w/ Power Back Door) |
w/o Rear No. 2 Seat:
![]() |
Remove the bolt.
Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.
w/ Rear No. 2 Seat:
![]() |
Disengage the 2 claws and 2 guides, and remove the rear No. 2 seat outer belt guide.
![]() |
Remove the bolt.
Disengage the 5 clips and 2 guides, and remove the roof side inner garnish assembly LH.
| 74. REMOVE REAR SEAT SIDE GARNISH CAP (w/o Rear Air Conditioning System) |
![]() |
Disengage the 8 claws and guide, and remove the rear seat side garnish cap.
| 75. REMOVE REAR SEAT SIDE GARNISH CAP (w/ Rear Air Conditioning System) |
![]() |
Remove the screw.
Disengage the 6 claws and the guide, and remove the rear seat side garnish cap.
| 76. REMOVE DECK SIDE TRIM COVER RH |
| 77. REMOVE DECK SIDE TRIM RH |
| 78. REMOVE SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System) |
![]() |
Disengage the 4 claws and remove the side trim cover RH.
| 79. REMOVE REAR ROOM TEMPERATURE SENSOR (w/ Rear Automatic Air Conditioning System) |
![]() |
Disengage the 4 claws and remove the rear room temperature sensor.
Disconnect the connector.
| 80. REMOVE REAR COMBINATION LIGHT SERVICE COVER RH |
![]() |
Using a screwdriver, disengage the 6 claws and the 2 guides, and remove the rear combination light service cover RH.
| 81. REMOVE ROPE HOOK ASSEMBLY (for RH Side) |
| 82. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK |
| 83. REMOVE FRONT DECK SIDE TRIM COVER RH |
| 84. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH |
| 85. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH |
Remove the 3 bolts.
Remove the 2 clips.
Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly RH.

| 86. REMOVE QUARTER PILLAR GARNISH RH |
| 87. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH (w/o Rear No. 2 Seat) |
| 88. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH (w/ Rear No. 2 Seat) |
| 89. REMOVE ROOF CONSOLE BOX ASSEMBLY |
![]() |
Using a moulding remover, disengage the 2 clips, 3 guides and fastener.
Disconnect the connector and remove the roof console box assembly.
| 90. REMOVE VISOR BRACKET COVER (for LH Side) |
![]() |
Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.
| 91. REMOVE VISOR ASSEMBLY LH |
![]() |
Remove the 2 screws and remove the visor assembly LH.
| 92. REMOVE VISOR BRACKET COVER (for RH Side) |
| 93. REMOVE VISOR ASSEMBLY RH |
| 94. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror) |
![]() |
Disengage the 2 claws and slide the inner rear view mirror stay holder cover as shown in the illustration.
![]() |
Disengage the 2 claws and remove the inner rear view mirror stay holder cover.
| 95. REMOVE NO. 1 ROOM LIGHT ASSEMBLY (for Standard) |
![]() |
Using a screwdriver, disengage the 4 claws and remove the lens cover.
![]() |
Using a screwdriver, disengage the 2 claws <A> as shown in the illustration.
Disengage the 2 claws <B>.
![]() |
Using a screwdriver, disengage the 4 claws and remove the No. 1 room light assembly.
| 96. REMOVE NO. 1 ROOM LIGHT ASSEMBLY (for Independent Type) |
![]() |
Using a screwdriver, disengage the 4 claws and remove the lens cover.
![]() |
Using a screwdriver, disengage the 2 claws <A> as shown in the illustration.
Disengage the 2 claws <B>.
![]() |
Using a screwdriver, disengage the 8 claws and remove the No. 1 room light assembly.
| 97. REMOVE NO. 2 ROOM LIGHT ASSEMBLY |
![]() |
Using a screwdriver, disengage the 4 claws and remove the lens cover.
![]() |
Using a screwdriver, disengage the 2 claws <A> as shown in the illustration.
Disengage the 2 claws <B>.
![]() |
Using a screwdriver, disengage the 4 claws and remove the No. 2 room light assembly.
| 98. REMOVE TELEVISION BASE (w/ Rear Seat Entertainment System) |
![]() |
Disengage the 4 clips and remove the television base.
| 99. REMOVE TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System) |
Disconnect the connector.
![]() |
Remove the 4 bolts.
![]() |
Disengage the 2 clips and 2 claws, and then remove the television display.
| 100. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof) |
![]() |
Using a clip remover, disengage the 4 claws.
![]() |
Pull off the 2 assist grip covers by hand.
Disengage the 2 clips and remove the front assist grip sub-assembly.
Remove the 2 clips from the vehicle body.
| 101. REMOVE REAR ASSIST GRIP SUB-ASSEMBLY (w/o Sliding Roof) |
![]() |
Using a clip remover, disengage the 4 claws.
Pull off the 2 assist grip covers by hand.
![]() |
Disengage the 2 clips and remove the rear assist grip sub-assembly.
Remove the 2 clips from the vehicle body.
| 102. REMOVE ASSIST GRIP ASSEMBLY (w/ Sliding Roof) |
![]() |
Using a screwdriver, disengage the 6 claws and remove the 2 assist grip covers.
![]() |
Disengage the 4 clips and remove the assist grip assembly.
Remove the 4 clips from the vehicle body.
| 103. REMOVE ROOF HEADLINING TRIM CLIP STOPPER |
![]() |
Using a screwdriver, disengage the 3 claws.
Remove the bolt and the roof headlining trim clip stopper.
| 104. REMOVE SUN ROOF OPENING TRIM MOULDING (w/ Sliding Roof) |
| 105. REMOVE VISOR HOLDER |
![]() |
Turn the visor holder approximately 45° and pull it out as shown in the illustration.
Disengage the 2 claws and remove the visor holder.
| 106. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof) |
Disconnect the No. 1 roof wire connector and disengage the 3 clamps from the front pillar LH.
Disconnect the No. 2 antenna cord sub-assembly connector, disengage the 3 clamps and remove the bolt from the front pillar RH.
Disconnect the No. 2 antenna cord sub-assembly connector from the rear pillar RH.
Remove the 4 clips.

![]() |
Remove the roof headlining assembly from the vehicle through the back door.
| 107. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof) |
Disconnect the No. 1 roof wire connectors and disengage the 3 clamps from the front pillar LH.
w/ Rear Seat Entertainment System:
Disconnect the No. 1 roof wire connector from the rear pillar LH.
Disconnect the No. 2 antenna cord sub-assembly connector, disengage the 3 clamps and remove the bolt from the front pillar RH.
Disconnect the No. 2 antenna cord sub-assembly connector from the rear pillar RH.
Disconnect the sliding roof drive gear connector.
Remove the 3 clips.

![]() |
Remove the roof headlining assembly from the vehicle through the back door.
| 108. REMOVE VANITY LIGHT ASSEMBLY |
![]() |
Disengage the 2 claws <A> and separate the bulb holder from the vanity light assembly as shown in the illustration.
Disengage the claw <B> and remove the vanity light assembly.