FUEL LID OPENER MOTOR ASSEMBLY > INSTALLATION |
| 1. INSTALL FUEL LID WITH MOTOR LOCK ASSEMBLY |
![]() |
Install the fuel lid with motor lock assembly with the nut.
Install the lock as shown in the illustration.
Connect the connector.
| 2. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH |
Engage the 4 clips and the 7 claws.
Install the 2 clips.
Install the deck trim side panel assembly LH with the 2 bolts.

| 3. CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH |
![]() |
Connect the floor anchor end of the rear No. 1 seat outer belt assembly and install the bolt.
| 4. INSTALL FRONT DECK SIDE TRIM COVER LH |
![]() |
Engage the 4 claws and install the 2 front deck side trim covers LH.
| 5. INSTALL NO. 2 DECK SIDE TRIM HOOK |
![]() |
Install the No. 2 deck side trim hook with the screw.
| 6. INSTALL ROPE HOOK ASSEMBLY |
![]() |
for Front Side:
Install the rope hook assembly with the bolt.
Engage the 2 claws.
![]() |
for Rear Side:
Install the rope hook assembly with the bolt.
Engage the 2 claws.
| 7. INSTALL REAR DECK TRIM COVER (w/o Remote Folding Function) |
![]() |
Engage the 10 claws and install the rear deck trim cover.
| 8. INSTALL RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function) |
![]() |
Engage the 5 claws and install the reclining remote control bezel lever LH.
| 9. INSTALL REAR POWER OUTLET SOCKET COVER |
![]() |
Engage the 2 claws and install the rear power outlet socket cover.
| 10. INSTALL REAR POWER POINT SOCKET ASSEMBLY |
![]() |
Engage the claw and install the rear power point socket assembly.
Connect the connector.
| 11. INSTALL REAR COMBINATION LIGHT SERVICE COVER LH |
![]() |
Engage the 2 guides and 6 claws, and install the rear combination light service cover LH.
| 12. INSTALL SIDE TRIM COVER LH (w/o Rear Seat Entertainment System) |
![]() |
Engage the 10 claws and install the side trim cover LH.
| 13. INSTALL POWER OUTLET SOCKET BEZEL (w/ Rear Seat Entertainment System) |
![]() |
Connect each connector.
![]() |
Engage the 4 claws and install the power outlet socket bezel.
| 14. INSTALL DECK SIDE TRIM LH |
![]() |
Engage the 3 guides and 4 claws as shown in the illustration.
![]() |
Install the deck side trim LH with the bolt.
| 15. INSTALL DECK SIDE TRIM COVER LH |
![]() |
Engage the 2 claws and install the deck side trim cover LH.
| 16. INSTALL REAR FLOOR FINISH PLATE |
![]() |
Engage the 4 clips and the 4 claws, and install the rear floor finish plate.
| 17. INSTALL REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat) |
![]() |
Install the rear No. 2 seat assembly with the 4 bolts.
| 18. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat) |
![]() |
Install the rear seat lap type belt assembly LH with the bolt.
| 19. CONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat) |
Install the rear seat lap type belt assembly RH with the bolt.
| 20. INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat) |
![]() |
Install the rear No. 2 seat inner belt assembly with the bolt.
| 21. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat) |
![]() |
Install the rear deck floor box with the 2 nuts.
| 22. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat) |
![]() |
Install the deck floor board assembly with the 4 nuts and 4 bolts.
| 23. INSTALL REAR MAT |
![]() |
Install the rear mat.
| 24. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat) |
![]() |
Install the 2 nuts and the deck floor board assembly.
Engage the 3 claws.
| 25. INSTALL DECK SIDE TRIM BOX LH |
Install the deck side trim box LH as shown in the illustration.

![]() |
Install the 2 deck side trim clip and the clips.
| 26. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat) |
![]() |
Engage the 2 clips and install the rear seat side cover LH.
| 27. INSTALL DECK SIDE TRIM BOX RH |
Install the deck side trim box RH as shown in the illustration.

![]() |
Install the 2 deck side trim clip and the clips.
| 28. INSTALL JACK CARRIER ASSEMBLY |
![]() |
Engage the 3 claws, and install the jack carrier assembly.
| 29. INSTALL JACK ASSEMBLY |
![]() |
Install the jack assembly.
| 30. INSTALL JACK CARRIER CUSHION |
![]() |
Install the jack carrier cushion.
| 31. INSTALL JACK CARRIER SUPPORT |
| 32. INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat) |
![]() |
Engage the 2 clips and install the rear seat side cover RH.
| 33. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat) |
![]() |
Engage the 3 guides and 3 clips and install the rear No. 1 floor board.
| 34. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Install the tonneau cover assembly.
| 35. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY |
![]() |
Engage the 2 guides and install the No. 2 deck board sub-assembly.
| 36. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY |
![]() |
Engage the 2 guides and install the No. 3 deck board sub-assembly.
| 37. INSTALL DECK BOARD ASSEMBLY |
![]() |
Install the deck board assembly.
| 38. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH |
![]() |
Align the alignment mark (red) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
| 39. INSTALL REAR DOOR SCUFF PLATE LH |
![]() |
Engage the guide, 3 clips and 5 claws, and install the rear door scuff plate LH.