REAR SPOILER > REMOVAL |
| 1. PRECAUTION |
| 2. REMOVE BACK WINDOW UPPER TRIM PANEL ASSEMBLY |
![]() |
Disengage the 4 clips and 4 claws, and remove the back window upper trim panel assembly.
| 3. REMOVE BACK DOOR TRIM COVER LH (w/o Power Back Door) |
![]() |
Disengage the 2 clips and 2 claws, and remove the back door trim cover LH.
| 4. REMOVE BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door) |
![]() |
Disengage the 6 claws, and remove the back door service hole cover LH.
| 5. DISCONNECT POWER BACK DOOR ROD (w/ Power Back Door) |
![]() |
Disconnect the power back door rod and remove the back door stay plate.
| 6. REMOVE BACK DOOR TRIM COVER LH (w/ Power Back Door) |
![]() |
Disengage the 2 clips and 2 claws, and remove the back door trim cover LH.
| 7. REMOVE BACK DOOR TRIM COVER RH |
![]() |
Disengage the 2 clips and 2 claws, and remove the back door trim cover RH.
| 8. REMOVE BACK DOOR LOCK COVER (for Glass Hatch Type) |
![]() |
Disengage the 2 claws and 4 guides, and remove the back door lock cover.
| 9. REMOVE ASSIST STRAP HOLE COVER |
![]() |
Disengage the 2 claws and 2 guides, and remove the assist strap hole cover.
| 10. REMOVE ASSIST STRAP ASSEMBLY |
![]() |
Remove the bolt and assist strap assembly.
| 11. REMOVE BACK DOOR TRIM PANEL ASSEMBLY |
![]() |
Disengage the 16 clips and remove the back door trim panel assembly.
| 12. REMOVE REAR WIPER SHAFT COVER (for Glass Hatch Type) |
![]() |
Disengage the 3 clips and remove the rear wiper shaft cover.
| 13. REMOVE REAR WIPER ARM HEAD CAP |
![]() |
Remove the rear wiper arm head cap.
| 14. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY |
![]() |
Remove the nut and the rear wiper arm and blade assembly.
| 15. REMOVE REAR WIPER LINK CAP (for Glass Hatch Type) |
![]() |
Remove the rear wiper link cap.
| 16. REMOVE REAR WIPER MOTOR GROMMET (for Fixed Glass Type) |
![]() |
Remove the rear wiper motor grommet.
| 17. REMOVE REAR WIPER LINK PIVOT (for Glass Hatch Type) |
![]() |
Remove the nut and the rear wiper link pivot.
| 18. REMOVE REAR WIPER MOTOR ASSEMBLY (for Fixed Glass Type) |
![]() |
Disconnect the connector.
Remove the 4 bolts and the rear wiper motor assembly.
| 19. REMOVE REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type) |
When reinstalling the rear wiper motor assembly :
Open the glass hatch.
![]() |
Engage the 3 claws and 2 guides, and then install the centering jig.
![]() |
Close the glass hatch, and engage the 2 claws and guide.
![]() |
Disconnect the connector.
Remove the 2 nuts.
Remove the 4 bolts and the rear wiper motor assembly.
When using a new rear wiper motor assembly:
![]() |
Disconnect the connector.
Remove the 4 bolts.
![]() |
Remove the 2 nuts and the rear wiper motor assembly.
| 20. REMOVE BACK DOOR GLASS GUIDE BRACKET SUB-ASSEMBLY (for Fixed Glass Type) |
![]() |
Loosen the bolt <A>.
Remove the 3 bolts <B>.
![]() |
Disengage the clip and remove the back door glass guide bracket sub-assembly.
| 21. REMOVE REAR SPOILER SUB-ASSEMBLY |
![]() |
Put protective tape around the rear spoiler sub-assembly.
Disconnect the wire harness.
![]() |
Turn back the wire harness grommet.
Disengage the 4 claws and pull out the wire harness from the vehicle.
![]() |
Disconnect the 2 connectors.
Disconnect the rear washer hose.
![]() |
Disengage the grommet.
Disconnect the connector.
Using a "TORX" socket wrench (T30), remove the 2 screws (A).
Using a "TORX" socket wrench (T30), remove the 6 screws (B).

Disengage the 2 claws.

![]() |
Raise and lower the glass hatch and the back door respectively. Pull out the wire harness from the vehicle and remove the rear spoiler sub-assembly.
| 22. REMOVE REAR WASHER NOZZLE (for Rear Spoiler without Press Line) |
![]() |
Remove the screw and rear washer nozzle bracket.
![]() |
Disengage the claws and remove the rear washer nozzle.
| 23. REMOVE CENTER STOP LIGHT ASSEMBLY (for Rear Spoiler without Press Line) |
![]() |
Remove the 2 screws.
Disconnect the center stop light assembly from the rear spoiler sub-assembly.
Disconnect the connector and remove the center stop light assembly.
| 24. REMOVE REAR WASHER NOZZLE (for Rear Spoiler with Press Line) |
![]() |
Remove the screw and rear washer nozzle bracket.
![]() |
Disengage the claws and remove the rear washer nozzle.
| 25. REMOVE CENTER STOP LIGHT ASSEMBLY (for Rear Spoiler with Press Line) |
![]() |
Remove the 2 screws.
Disconnect the center stop light assembly from the rear spoiler sub-assembly.
Disconnect the connector and remove the center stop light assembly.