Home › BODY › ENGINE HOOD / DOOR › BACK DOOR CLOSER SYSTEM

BACK DOOR CLOSER SYSTEM > Back Door Closer does not Operate

for Preparation Click here


DESCRIPTION

When the back door closer does not operate, one of the following may be the cause 1) improper fit of back door, or a foreign object is stuck in back door, or 2) initialization of the power back door ECU, or a malfunction in the 3) power back door ECU power source circuit, or 4) back door lock circuit, or 5) power back door ECU.

WIRING DIAGRAM


B165216E04


INSPECTION PROCEDURE

1.CHECK BACK DOOR LOCK FUNCTION
  1. Check if the back door is fully closed by hand.



NG
IMPROPER FIT OF BACK DOOR, OR A FOREIGN OBJECT IS STUCK IN BACK DOOR
OK


2.INITIALIZE POWER BACK DOOR ECU
  1. Check that the power back door drive unit (power back door ECU) can be initialized (Click here).


NEXT


3.CHECK BACK DOOR CLOSER SYSTEM
  1. Check that the back door closer system operation.

    OK:
    Back door closer system operates normally.



NG
Go to step 4
OK

END 

4.CHECK DTC OUTPUT
  1. Check for the DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    B2250 is output
    B
    B2251 is output
    C



B
GO TO DTC CHART (B2250) (Click here)

C
GO TO DTC CHART (B2251) (Click here)
A


5.INSPECT FUSE (ECU IG NO. 1, ECU-B)
  1. Remove the ECU IG No. 1 fuse from the instrument panel junction block and ECU-B fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU IG NO. 1
    Always
    Below 1 Ω
    ECU-B
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


6.CHECK FUSIBLE LINK BLOCK ASSEMBLY (PBD FUSE)
  1. Remove the fusible link block assembly.



    B165197E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A - B
    Always
    Below 1 Ω

    HINT:
    PBD 30A fuse is located in the fusible link block assembly.



NG
REPLACE FUSIBLE LINK BLOCK ASSEMBLY
OK


7.CHECK HARNESS AND CONNECTOR (BODY GROUND)
  1. Disconnect the O15 power back door ECU connector.



    B165208E09
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    O15-8 (IG) - Body ground
    power switch on (IG)
    11 to 14 V
    O15-10 (ECUB) - Body ground
    Always
    11 to 14 V
    O15-12 (B) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
  1. Disconnect the O15 power back door ECU connector.



    B165208E10
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    O15-11 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT BACK DOOR LOCK

B143899E07

  1. Remove the back door lock.

  1. Apply battery voltage and check operation of the door lock motor.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1 (DC+)
    Battery negative (-) → Terminal 2 (DC-)
    Latch turns to full-latch position
    Battery positive (+) → Terminal 2 (DC-)
    Battery negative (-) → Terminal 1 (DC+)
    Latch turns to open-latch position

  1. Measure the resistance of the switch.

    Standard resistance:
    Full-latch switch:
    Tester Connection
    Door Lock Latch Position
    Specified Condition
    5 (HAF) - 4 (GND)
    Over-latch
    Below 1 Ω
    5 (HAF) - 4 (GND)
    Open-latch
    10 kΩ or higher
    5 (HAF) - 4 (GND)
    Full-latch
    10 kΩ or higher
    5 (HAF) - 4 (GND)
    Half-latch
    10 kΩ or higher
    Back door courtesy light switch:
    Tester Connection
    Door Lock Latch Position
    Specified Condition
    3 (BDCY) - 4 (GND)
    Open-latch
    Below 1 Ω
    3 (BDCY) - 4 (GND)
    Half-latch
    Below 1 Ω
    3 (BDCY) - 4 (GND)
    Full-latch
    10 kΩ or higher
    3 (BDCY) - 4 (GND)
    Over-latch
    10 kΩ or higher



NG
REPLACE BACK DOOR LOCK (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK - POWER BACK DOOR ECU AND BODY GROUND)


    B165204E01
  1. Disconnect the T4 door lock connector.

  1. Disconnect the O15 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    T4-1 (DC+) - O15-2 (DC+)
    Always
    Below 1 Ω
    T4-2 (DC-) - O15-1 (DC-)
    Always
    Below 1 Ω
    T4-5 (HAF) - O15-22 (HAF)
    Always
    Below 1 Ω
    T4-6 (POS) - O15-24 (POS)
    Always
    Below 1 Ω
    T4-3 (BDCY) - O15-20 (FUL)
    Always
    Below 1 Ω
    T4-4 (GND) - Body ground
    Always
    Below 1 Ω
    T4-1 (DC+) - Body ground
    Always
    10 kΩ or higher
    T4-2 (DC-) - Body ground
    Always
    10 kΩ or higher
    T4-5 (HAF) - Body ground
    Always
    10 kΩ or higher
    T4-6 (POS) - Body ground
    Always
    10 kΩ or higher
    T4-3 (BDCY) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER BACK DOOR DRIVE UNIT (POWER BACK DOOR ECU) (Click here)