Home › ENGINE › 3MZ-FE ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0112    Intake Air Temperature Circuit Low Input

DTC    P0113    Intake Air Temperature Circuit High Input

for Preparation Click here


DESCRIPTION

The intake air temperature sensor, in the mass air flow meter, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM (included in the hybrid vehicle control ECU) as voltage changes (See Fig. 1).
The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.
Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, the voltage at terminal THA also varies according to changes in the intake air temperature. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve drivability.
A067628E30

HINT:
When any of DTCs P0110, P0112 and P0113 are set, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.


DTC No.
Proceed to
DTC Detection Condition
Trouble Area
P0112
Step 4
Short in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Short in intake air temperature sensor circuit
  2. Intake air temperature sensor (built into mass air flow meter meter)
  3. Hybrid vehicle control ECU
P0113
Step 2
Open in intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic)
  1. Open in intake air temperature sensor circuit
  2. Intake air temperature sensor (built into mass air flow meter meter)
  3. Hybrid vehicle control ECU

HINT:
When any of these DTCs are set, check the intake air temperature by entering the following menus on the Techstream: Powertrain / Engine and ECT / Data List / Intake Air.

Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or higher
Short circuit


MONITOR DESCRIPTION

The ECM (included in the hybrid vehicle control ECU) monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor and sets a DTC.
Example:
If the sensor output voltage is -40°C (-40°F) for 0.5 seconds or more, the ECM determines that there is an open in the intake air temperature sensor circuit, and sets DTC P0113. Conversely, if the output voltage is more than 140°C (284°F) for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and sets DTC P0112.
If the malfunction is not repaired successfully, a DTC is set 0.5 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0110: Intake air temperature sensor open/short (Fluctuating)
P0112: Intake air temperature sensor short (Low electrical resistance)
P0113: Intake air temperature sensor open (High electrical resistance)
Required Sensors/Components (Main)
Intake air temperature sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Continuous
Duration
0.5 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
None

TYPICAL MALFUNCTION THRESHOLDS


P0112: 
Intake air temperature sensor voltage
Less than 0.18 V

P0113: 
Intake air temperature sensor voltage
More than 4.91 V

COMPONENT OPERATING RANGE


Intake air temperature sensor voltage
0.18 to 4.90 V [-40 to 140°C (-40 to 284°F)]

WIRING DIAGRAM


A182710E02


INSPECTION PROCEDURE

HINT:
  1. If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the Techstream. The ECM (included in the hybrid vehicle control ECU) records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.

1.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the Techstream.

    Standard:
    Same as actual intake air temperature.


    Result:

    Temperature Displayed
    Proceed to
    -40 °C (-40°F)
    A
    140°C (284°F) or higher
    B
    Same as actual intake air temperature
    C

    HINT:
    1. If there is an open circuit, the Techstream indicates -40°C (-40°F).
    2. If there is a short circuit, the Techstream indicates 140°C (284°F) or higher.



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.READ VALUE USING TECHSTREAM (CHECK FOR OPEN IN WIRE HARNESS)


    A178387E03
  1. Disconnect the mass air flow meter connector.

  1. Connect terminals THA and E2 of the mass air flow meter wire harness side connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the Techstream.

    Standard:
    140°C (284°F) or higher

  1. Reconnect the mass air flow meter connector.



NG
Go to step 3
OK

REPLACE MASS AIR FLOW METER (Click here)  

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - HYBRID VEHICLE CONTROL ECU)


    A178386E06
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the hybrid vehicle control ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Check for open 
    Tester Connection
    Condition
    Specified Condition
    B1-20 (THA) - B10-4 (THA)
    Always
    Below 1 Ω
    B1-28 (E2) - B10-5 (E2)
    Always
    Below 1 Ω
    Check for short 
    Tester Connection
    Condition
    Specified Condition
    B1-20 (THA) or B10-4 (THA) - Body ground
    Always
    10 kΩ or higher
    B1-28 (E2) or B10-5 (E2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the hybrid vehicle control ECU.



NG
REPLACE HYBRID VEHICLE CONTROL ECU (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - HYBRID VEHICLE CONTROL ECU) 

4.READ VALUE USING TECHSTREAM (CHECK FOR SHORT IN WIRE HARNESS)


    A178388E03
  1. Disconnect the mass air flow meter connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the Techstream.

    Standard:
    -40°C (-40°F) or higher

  1. Reconnect the mass air flow meter connector.



NG
Go to step 5
OK

REPLACE MASS AIR FLOW METER (Click here)  

5.READ VALUE USING TECHSTREAM


    A178389E02
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the hybrid vehicle control ECU connector.

  1. Connect the Techstream to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air.

  1. Read the value displayed on the Techstream.

    Standard:
    -40°C (-40°F) or higher

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the hybrid vehicle control ECU connector.



NG
REPLACE HYBRID VEHICLE CONTROL ECU
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - HYBRID VEHICLE CONTROL ECU)