Home › ENGINE › 3MZ-FE ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > INSPECTION

for Preparation Click here



1. INSPECT CYLINDER HEAD SUB-ASSEMBLY


    A080656E02
  1. Using a precision straight edge and a feeler gauge, measure the warpage of the contacting surface between the cylinder block and the manifolds.

    Maximum Warpage:
    Cylinder block surface
    Intake manifold surface
    Exhaust manifold surface
    0.05 mm (0.0020 in.)
    0.10 mm (0.0039 in.)
    0.10 mm (0.0039 in.

    If warpage is greater than the maximum, replace the cylinder head.



2. INSPECT CYLINDER HEAD FOR CRACKS


    A005227E01
  1. Using a dye penetrant, check the combustion chamber, intake ports, exhaust ports and cylinder block surface for cracks. If cracked, replace the cylinder head.



3. INSPECT INTAKE VALVE


    A101394E01
  1. Check the valve overall length.

    Standard overall length:
    95.45 mm (3.7579 in.)

    Minimum overall length:
    94.95 mm (3.7382 in.)



    A101395
  1. Using a micrometer, measure the diameter of the valve stem.

    Valve stem diameter:
    5.470 to 5.485 mm (0.2154 to 0.2159 in.)



    A101396E03
  1. Check the valve head margin thickness.

    Standard margin thickness:
    1.0 mm (0.039 in.)

    Minimum margin thickness:
    0.5 mm (0.020 in.)



4. INSPECT EXHAUST VALVE


    A101397E01
  1. Check the valve overall length.

    Standard overall length:
    95.40 mm (3.7559 in.)

    Minimum overall length:
    94.90 mm (3.7362 in.)



    Z000052
  1. Using a micrometer, measure the diameter of the valve stem.

    Valve stem diameter:
    5.465 to 5.480 mm (0.2152 to 0.2157 in.)



    A101399E01
  1. Check the valve head margin thickness.

    Standard margin thickness:
    1.0 mm (0.039 in.)

    Minimum margin thickness:
    0.5 mm (0.020 in.)



5. INSPECT INNER COMPRESSION SPRING


    A101392
  1. Using vernier calipers, measure the free length of the valve spring.

    Free length:
    45.50 mm (1.7913 in.)



    A101393E01
  1. Using a steel square, measure the deviation of the valve spring.

    Maximum deviation:
    2.0 mm (0.079 in.)



    EM00281E01
  1. Using a spring tester, measure the tension of the valve spring at the specified installed length.

    Installed tension:
    186 to 206 N (19.0 to 21.0 kgf, 41.9 to 46.3 lbf) at 33.8 mm (1.331 in.)

    If the installed tension is not as specified, replace the valve spring.



6. INSPECT VALVE GUIDE BUSHING OIL CLEARANCE


    A109552
  1. Using a caliper gauge, measure the inside diameter of the guide bushing.

    Bushing inside diameter:
    5.510 to 5.530 mm (0.2169 to 0.2177 in.)

  1. Subtract the valve stem diameter measurement from the guide bushing inside diameter measurement.

    Standard oil clearance:
    Intake
    Exhaust
    0.025 to 0.060 mm (0.0010 to 0.0024 in.)
    0.030 to 0.065 mm (0.0012 to 0.0026 in.)

    Maximum oil clearance:
    Intake
    Exhaust
    0.08 mm (0.0031 in.)
    0.10 mm (0.0039 in.)



7. INSPECT VALVE SEATS
  1. Apply a light coat of prussian blue (or white lead) to the valve face.

  1. Lightly press the valve against the seat.

    NOTICE:
    Do not rotate the valve.



    A078779E01
  1. Check the valve face and seat according to the following procedure.

    1. If prussian blue appears around the entire face, the valve is concentric. If not, replace the valve.

    2. If prussian blue appears around the entire valve seat, the guide and face are concentric. If not, resurface the seat.

    3. Check that the seat contacts in the middle of the valve face with the width between 1.0 and 1.4 mm (0.039 and 0.055 in.).



8. INSPECT VALVE LIFTER


    A102801
  1. Using a micrometer, measure the lifter diameter.

    Lifter diameter:
    30.966 to 30.976 mm (1.2191 to 1.2195 in.)



9. INSPECT VALVE LIFTER OIL CLEARANCE


    P012685E01
  1. Using a caliper gauge, measure the lifter bore diameter of the cylinder head.

    Lifter bore diameter:
    31.009 to 31.025 mm (1.2208 to 1.2215 in.)

  1. Subtract the lifter diameter measurement from the lifter bore diameter measurement.

    Standard oil clearance:
    0.033 to 0.059 mm (0.0013 to 0.0023 in.)

    Maximum oil clearance:
    0.07 mm (0.0028 in.)