Home › HYBRID SYSTEM · P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

HYBRID CONTROL SYSTEM > TERMINALS OF ECU

for Preparation Click here



A175700E02


TERMINALS OF HYBRID VEHICLE CONTROL ECU 
Terminal No.
(Symbol)
Wiring Color
Terminal Description
Condition
Standard Voltage
(V)
D35-1 (BATT) - B3-5 (E1)
R - W-B
Constant power source
Always
11 to 14
D35-3 (TC) - B3-5 (E1)
L - W-B
Diagnostic terminal
Power switch on (IG)
11 to 14
D35-4 (PMET) - B3-5 (E1)
W - W-B
Power meter signal
Power switch on (IG)
Pulse generation
(Waveform 1)
D35-8 (ABFS) - B3-5 (E1)
SB - W-B
Airbag activation signal
Power switch on (READY) (2 seconds after turning power switch on (ACC))
Pulse generation
(Waveform 2)
D35-9 (IGSW) - B3-5 (E1)
G - W-B
IG signal
Power switch on (IG)
11 to 14
D35-9 (IGSW) - B3-5 (E1)
G - W-B
IG signal
Power switch off to on (READY)
Pulse generation
(Waveform 3)
D35-12 (RDY) - B3-5 (E1)
O - W-B
READY control signal
Power switch on (IG)
Power switch off to on (READY)
Pulse generation
(Waveform 4)
D35-17 (EVSW) - B3-5 (E1)
O - W-B
EV mode switch
Power switch on (IG), EV mode switch on
Below 1.5
D35-17 (EVSW) - B3-5 (E1)
O - W-B
EV mode switch
Power switch on (IG), EV mode switch off
11 to 14
D35-20 (ST2) - B3-5 (E1)
Y - W-B
Starter signal
Power switch on (IG)
0 to 1.5
D35-23 (IWP) - B3-5 (E1)
V - W-B
HV water pump signal
Power switch on (READY)
11 to 14
Pulse generation
(Waveform 5)
D35-29 (NIWP) - B3-5 (E1)
P - W-B
HV water pump signal
Power switch on (READY)
Pulse generation
(Waveform 5)
D35-24 (SPDI) - B3-5 (E1)
G - W-B
Vehicle speed signal
Approximately 12 mph (20 km/h)
Pulse generation
(Waveform 6)
D35-25 (ST1-) - B3-5 (E1)
LG - W-B
Brake cancel switch
Power switch on (IG), brake pedal depressed
Below 0.5
D35-25 (ST1-) - B3-5 (E1)
LG - W-B
Brake cancel switch
Power switch on (IG), brake pedal released
11 to 14
D35-22 (IMI) - B3-5 (E1)
L - W-B
Immobilizer communication
Immobilizer communicating
Pulse generation
(Waveform 7)
D35-28 (IMO) - B3-5 (E1)
BR - W-B
Immobilizer communication
Immobilizer communicating
Pulse generation
(Waveform 7)
D35-30 (THB) - B1-28 (E2)
V - BR
Auxiliary battery thermometer sensor signal
Auxiliary battery temperature 77°F (25°C)
1.8 to 2.4
D35-30 (THB) - B1-28 (E2)
V - BR
Auxiliary battery thermometer sensor signal
Auxiliary battery temperature 140°F (60°C)
0.7 to 1.3
D35-31 (STP) - B3-5 (E1)
R - W-B
Stop light switch
Brake pedal depressed
11 to 14
D35-31 (STP) - B3-5 (E1)
R - W-B
Stop light switch
Brake pedal released
Below 5
D36-1 (CON3) - B3-5 (E1)
O - W-B
System main relay
Power switch off to on (READY)
Pulse generation
(Waveform 3)
D36-2 (CON2) - B3-5 (E1)
GR - W-B
System main relay
Power switch off to on (READY)
Pulse generation
(Waveform 3)
D36-3 (CON1) - B3-5 (E1)
LG - W-B
System main relay
Power switch off to on (READY)
Pulse generation
(Waveform 3)
D36-4 (ILK) - B3-5 (E1)
W - W-B
Interlock switch
Power switch on (IG), inverter cover and service plug grip installed correctly
Below 1
D36-4 (ILK) - B3-5 (E1)
W - W-B
Interlock switch
Power switch on (IG), inverter cover and service plug grip detached
11 to 14
D36-9 (SNWI) - B3-5 (E1)
SB - W-B
ECON mode switch
Power switch on (IG), ECON mode switch on
Below 1.5
D36-9 (SNWI) - B3-5 (E1)
SB - W-B
ECON mode switch
Power switch on (IG), ECON mode switch off
11 to 14
D36-13 (SI2) - B3-5 (E1)
LG - W-B
HV battery blower fan
Power switch on (IG), during active test
Pulse generation
(Waveform 8)
D36-14 (SI1) - B3-5 (E1)
O - W-B
HV battery blower fan
Power switch on (IG), during active test
Pulse generation
(Waveform 8)
D36-15 (SI0) - B3-5 (E1)
P - W-B
HV battery blower fan
Power switch on (IG), during active test
Pulse generation
(Waveform 8)
D36-19 (BTH+) - B3-5 (E1)
BR - W-B
Communication from battery to HV
Power switch on (IG)
Pulse generation
(Waveform 9)
D36-30 (BTH-) - B3-5 (E1)
Y - W-B
Communication from battery to HV
Power switch on (IG)
Pulse generation
(Waveform 9)
D36-21 (RMT) - D36-20 (RMTG)
GR - V
Rear motor temperature sensor
Refer to DATA LIST
-
D36-25 (CANH) - B3-5 (E1)
B - W-B
CAN communication system
Power switch on (IG)
Pulse generation
(Waveform 10)
D36-33 (CANL) - B3-5 (E1)
W - W-B
CAN communication system
Power switch on (IG)
Pulse generation
(Waveform 10)
A43-1 (+B2) - B3-5 (E1)
Y - W-B
Power source
Power switch on (IG)
11 to 14
A43-2 (+B1) - B3-5 (E1)
GR - W-B
Power source
Power switch on (IG)
11 to 14
A43-5 (OPM2) - B3-5 (E1)
P - W-B
Oil pump
Power switch on (READY)
11 to 14
A43-6 (OPM1) - B3-5 (E1)
R - W-B
Oil pump
Power switch on (READY)
Pulse generation
(Waveform 11)
A43-7 (OPST) - B3-5 (E1)
L - W-B
Oil pump
Power switch on (READY)
Pulse generation
(Waveform 11)
A43-9 (FCTL) - B3-5 (E1)
G - W-B
Cooling fan relay
Power switch on (IG)
11 to 14
Pulse generation
(Waveform 8)
A43-10 (RFC2) - B3-5 (E1)
BR - W-B
Radiator fan
Power switch on (READY), engine started
Pulse generation
(Waveform 12)
A43-11 (NODD) - B3-5 (E1)
W - W-B
DC/DC operation monitor/stop request signal
Converter operating normally
5 to 7
A43-11 (NODD) - B3-5 (E1)
W - W-B
DC/DC operation monitor/stop request signal
Converter not operating normally
2 to 4
A43-11 (NODD) - B3-5 (E1)
W - W-B
DC/DC operation monitor/stop request signal
Converter ordered to stop
0.1 to 0.4
A43-12 (MREL) - B3-5 (E1)
Y - W-B
Main relay
Power switch on (IG)
11 to 14
A43-14 (RFC1) - B3-5 (E1)
V - W-B
Radiator fan
Power switch on (READY), engine started
Pulse generation
(Waveform 12)
A43-15 (GO) - B3-5 (E1)
W - W-B
GO signal
Engine running
Pulse generation
(Waveform 13)
B3-25 (NE+) - B3-24 (NE-)
R - G
Crankshaft position
Engine running
Pulse generation
(Waveform 14)
A43-16 (NEO) - B3-5 (E1)
B - W-B
Engine speed signal
Engine running
Pulse generation
(Waveform 15)
A43-18 (HTM+) - B3-5 (E1)
B - W-B
Communication from HV to MG
Power switch on (IG)
Pulse generation
(Waveform 16)
A43-17 (HTM-) - B3-5 (E1)
W - W-B
Communication from HV to MG
Power switch on (IG)
Pulse generation
(Waveform 16)
A43-21 (HSDN) - B3-5 (E1)
B - W-B
MG shutdown signal
Power switch on (READY)
Below 2
A43-22 (CLK+) - B3-5 (E1)
B - W-B
MG communication clock signal
Power switch on (IG)
Pulse generation
(Waveform 17)
A43-29 (CLK-) - B3-5 (E1)
W - W-B
MG communication clock signal
Power switch on (IG)
Pulse generation
(Waveform 17)
A43-23 (REQ+) - B3-5 (E1)
B - W-B
MG communication request signal
Power switch on (IG)
Pulse generation
(Waveform 18)
A43-30 (REQ-) - B3-5 (E1)
W - W-B
MG communication request signal
Power switch on (IG)
Pulse generation
(Waveform 18)
A43-24 (VCP1) - A43-33 (EP1)
G - W
Accelerator pedal position sensor power source (for VPA1)
Power switch on (IG)
4.5 to 5.5
A43-25 (VPA) - A43-33 (EP1)
BR - W
Accelerator pedal position sensor (for accelerator pedal position detection)
Power switch on (IG), accelerator pedal released
0.4 to 1.4
A43-25 (VPA) - A43-33 (EP1)
BR - W
Accelerator pedal position sensor (for accelerator pedal position detection)
Power switch on (IG), engine stopped, shift lever in the P position, accelerator pedal fully depressed
2.6 to 4.5
A43-31 (VCP2) - A43-32 (EP2)
L - Y
Accelerator pedal position sensor power source (for VPA2)
Power switch on (IG)
4.5 to 5.5
A43-26 (VPA2) - A43-32 (EP2)
R - Y
Accelerator pedal position sensor (for sensor malfunction detection)
Power switch on (IG), accelerator pedal released
1.0 to 2.2
A43-26 (VPA2) - A43-32 (EP2)
R - Y
Accelerator pedal position sensor (for sensor malfunction detection)
Power switch on (IG), engine stopped, shift lever in the P position, accelerator pedal fully depressed
3.4 to 5.3
A43-28 (MTH+) - B3-5 (E1)
B - W-B
Communication from MG to HV
Power switch on (READY)
Pulse generation
(Waveform 19)
A43-27 (MTH-) - B3-5 (E1)
W - W-B
Communication from MG to HV
Power switch on (READY)
Pulse generation
(Waveform 19)
B3-12 (P) - B3-5 (E1)
L - W-B
Shift lever position sensor
Power switch on (IG), shift lever in the P position
11 to 14
B3-12 (P) - B3-5 (E1)
L - W-B
Shift lever position sensor
Power switch on (IG), shift lever not in the P position
0
B3-11 (R) - B3-5 (E1)
G - W-B
Shift lever position sensor
Power switch on (IG), shift lever in the R position
11 to 14
B3-11 (R) - B3-5 (E1)
G - W-B
Shift lever position sensor
Power switch on (IG), shift lever not in the R position
0
B3-10 (N) - B3-5 (E1)
B - W-B
Shift lever position sensor
Power switch on (IG), shift lever in the N position
11 to 14
B3-10 (N) - B3-5 (E1)
B - W-B
Shift lever position sensor
Power switch on (IG), shift lever not in the N position
1 to 2.5
B3-9 (D) - B3-5 (E1)
Y - W-B
Shift lever position sensor
Power switch on (IG), shift lever in the D position
11 to 14
B3-9 (D) - B3-5 (E1)
Y - W-B
Shift lever position sensor
Power switch on (IG), shift lever not in the D position
0
B3-8 (B) - B3-5 (E1)
BR - W-B
Shift lever position sensor
Power switch on (IG), shift lever in the B position
11 to 14
B3-8 (B) - B3-5 (E1)
BR - W-B
Shift lever position sensor
Power switch on (IG), shift lever not in the B position
0
B2-10 (MJ) - B3-5 (E1)
G - W-B
Shift lever position sensor
Power switch on (IG), shift lever in the P, R, N, D or B position
11 to 14
B2-11 (FD) - B3-5 (E1)
W - W-B
Shift lever position sensor
Power switch on (IG), shift lever in the D or B position
11 to 14
B2-11 (FD) - B3-5 (E1)
W - W-B
Shift lever position sensor
Power switch on (IG), shift lever not in the D or B position
0
B2-12 (RV) - B3-5 (E1)
B - W-B
Shift lever position sensor
Power switch on (IG), shift lever in the R position
11 to 14
B2-12 (RV) - B3-5 (E1)
B - W-B
Shift lever position sensor
Power switch on (IG), shift lever not in the R position
0
B2-14 (CLK) - B3-5 (E1)
G - W-B
A/C communication signal
Power switch on (READY)
Pulse generation
(Waveform 20)
B2-15 (ITE) - B3-5 (E1)
P - W-B
A/C communication signal
Power switch on (READY)
Pulse generation
(Waveform 20)
B2-16 (ETI ) - B3-5 (E1)
Y - W-B
A/C communication signal
Power switch on (READY)
Pulse generation
(Waveform 20)
B2-18 (STB) - B3-5 (E1)
B - W-B
A/C communication signal
Power switch on (READY)
Pulse generation
(Waveform 20)
A43-4 (WP) - B3-5 (E1)
V - W-B
A/C WP relay signal
Power switch on (READY)
Below 2
B1-22 (GMT) - B1-32 (GMTG)
L - P
Generator temperature sensor
Refer to DATA LIST
-
B1-26 (MMT) - B1-33 (MMTG)
G - R
Motor temperature sensor
Refer to DATA LIST
-
B1-27 (AS1) - B1-34 (AS1G)
V - W
Circuit breaker sensor
Satellite signal system operating normally
2.3 to 3.1

Oscilloscope waveforms

HINT:
Oscilloscope waveform samples are provided here for informational purposes. Noise and fluttering waveforms have been omitted.



    A111589E01
  1. Waveform 1 (power meter signal)
    Item
    Contents
    Terminal
    PMET - E1
    Equipment Setting
    5 V/DIV., 50 ms./DIV.
    Condition
    Power switch on (IG)



  2. A111590E01
  3. Waveform 2 (airbag activation signal)
    Item
    Contents
    Terminal
    ABFS - E1
    Equipment Setting
    5 V/DIV., 500 ms./DIV.
    Condition
    Power switch on (READY)



  4. A111595E01
  5. Waveform 3 (system main relay operation signal)
    Item
    Contents
    Terminal
    CH1: IGSW - E1
    CH2: CON1 - E1
    CH3: CON2 - E1
    CH4: CON3 - E1
    Equipment Setting
    10 V/DIV., 500 ms./DIV.
    Condition
    Power switch off to on (READY)



  6. A111591E09
  7. Waveform 4 (READY control signal)
    Item
    Contents
    Terminal
    RDY - E1
    Equipment Setting
    10 V/DIV., 10 ms./DIV.
    Condition
    Power switch on (IG)
    Power switch on (READY)



  8. A111592E01
  9. Waveform 5 (HV water pump signal)
    Item
    Contents
    Terminal
    CH1: IWP - E1
    CH2: NIWP - E1
    Equipment Setting
    5 V/DIV., 2 ms./DIV.
    Condition
    Power switch on (READY)



  10. A111593E01
  11. Waveform 6 (vehicle speed signal)
    Item
    Contents
    Terminal
    SPDI - E1
    Equipment Setting
    5 V/DIV., 20 ms./DIV.
    Condition
    Driving at approximately 12 mph (20 km/h) with power switch on (READY)

    HINT:
    The higher the vehicle speed, the shorter the cycle.



  12. A188618E01
  13. Waveform 7 (immobilizer communication signal)
    Item
    Contents
    Terminal
    CH1: IMO - E1
    CH2: IMI - E1
    Equipment Setting
    5 V/DIV., 200 ms./DIV.
    Condition
    Power switch off → Power switch on (IG) → Power switch on (READY)



  14. A111596E01
  15. Waveform 8 (HV battery blower fan operation signal)
    Item
    Contents
    Terminal
    CH1: SI0 - E1
    CH2: SI1 - E1
    CH3: SI2 - E1
    CH4: FCTL - E1
    Equipment Setting
    10 V/DIV., 200 ms./DIV.
    Condition
    Power switch on (IG), during active test

    HINT:
    The duty ratio varies depending on the cooling fun mode.



  16. A111597E01
  17. Waveform 9 (communication signal from battery smart unit to hybrid vehicle control ECU)
    Item
    Contents
    Terminal
    CH1: BTH+ - E1
    CH2: BTH- - E1
    Equipment Setting
    2 V/DIV., 500 μs./DIV.
    Condition
    Power switch on (IG)

    HINT:
    The waveform will vary depending on the content of the digital communication (digital signal).



  18. A111598E01
  19. Waveform 10 (CAN communication signal)
    Item
    Contents
    Terminal
    CH1: CANH - E1
    CH2: CANL - E1
    Equipment Setting
    1 V/DIV., 20 μs./DIV.
    Condition
    Power switch on (IG)

    HINT:
    The waveform will vary depending on the content of the digital communication (digital signal).



  20. A113983E01
  21. Waveform 11 (oil pump signal)
    Item
    Contents
    Terminal
    CH1: OPM1 - E1
    CH2: OPST - E1
    Equipment Setting
    5 V/DIV., 5 ms./DIV.
    Condition
    Power switch on (READY)



  22. A188620E01
  23. Waveform 12 (radiator fan operation signal)
    Item
    Contents
    Terminal
    CH1: RFC1 - E1
    CH2: RFC2 - E1
    Equipment Setting
    5 V/DIV., 1 ms./DIV.
    Condition
    Power switch on (READY) with engine running



  24. A111600E01
  25. Waveform 13 (GO signal)
    Item
    Contents
    Terminal
    GO - E1
    Equipment Setting
    5 V/DIV., 20 ms./DIV.
    Condition
    Power switch on (READY) with engine running

    HINT:
    The pulse cycle becomes shorter as the engine speed increases.



  26. A111601E01
  27. Waveform 14 (crankshaft position signal)
    Item
    Contents
    Terminal
    NE+ - NE-
    Equipment Setting
    5 V/DIV., 1 ms./DIV.
    Condition
    Power switch on (READY) with engine running

    HINT:
    The pulse cycle becomes shorter as the engine speed increases.



  28. A111602E01
  29. Waveform 15 (engine speed signal)
    Item
    Contents
    Terminal
    NEO - E1
    Equipment Setting
    10 V/DIV., 10 ms./DIV.
    Condition
    Power switch on (READY) with engine running

    HINT:
    The pulse cycle becomes shorter as the engine speed increases.



  30. A114529E01
  31. Waveform 16 (communication signal from hybrid vehicle control ECU to MG ECU)
    Item
    Contents
    Terminal
    CH1: HTM+ - E1
    CH2: HTM- - E1
    Equipment Setting
    1 V/DIV., 200 μs./DIV.
    Condition
    Power switch on (IG)

    HINT:
    The waveform will vary depending on the content of the digital communication (digital signal).



  32. A111604E01
  33. Waveform 17 (MG ECU communication clock signal)
    Item
    Contents
    Terminal
    CH1: CLK+ - E1
    CH2: CLK- - E1
    Equipment Setting
    1 V/DIV., 1 μs./DIV.
    Condition
    Power switch on (IG)



  34. A111605E01
  35. Waveform 18 (MG ECU communication request signal)
    Item
    Contents
    Terminal
    CH1: REQ+ - E1
    CH2: REQ- - E1
    Equipment Setting
    1 V/DIV., 1 ms./DIV.
    Condition
    Power switch on (IG)



  36. A114530E01
  37. Waveform 19 (communication signal from MG ECU to hybrid vehicle control ECU)
    Item
    Contents
    Terminal
    CH1: MTH+ - E1
    CH2: MTH- - E1
    Equipment Setting
    1 V/DIV., 200 μs./DIV.
    Condition
    Power switch on (READY)

    HINT:
    The waveform will vary depending on the content of the digital communication (digital signal).



  38. A111607E01
  39. Waveform 20 (A/C communication signal)
    Item
    Contents
    Terminal
    CH1: CLK - E1
    CH2: ITE - E1
    CH3: ETI - E1
    CH4: STB - E1
    Equipment Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Power switch on (READY) with A/C stopped

    HINT:
    The waveform will vary depending on the content of the digital communication (digital signal).


A183548E01

HINT:
Connectors A, B, and C are located inside the inverter with converter assembly and usually not inspected. Terminal arrangement and measured values are provided as a reference.


TERMINALS OF MG ECU 
Terminal No.
(Symbol)
Wiring Color
Terminal Description
Condition
Standard voltage
(V)
C-1 (RVSPI) - C-18 (RSG)
-
Power source for rear current sensor
Power switch on (IG)
14.25 to 15.75
C-2 (RVSPO) - C-18 (RSG)
-
Power source for rear current sensor
Power switch on (IG)
14.25 to 15.75
C-6 (RVSNO) - C-18 (RSG)
-
Power source for rear current sensor
Power switch on (IG)
-15.9 to -14.1
C-7 (RVSNI) - C-18 (RSG)
-
Power source for rear current sensor
Power switch on (IG)
-15.9 to -14.1
C-8 (RIT) - C-19 (RIVG)
-
Rear motor inverter temperature
Power switch on (IG)
1.5 to 4.5
C-9 (RFIV) - C-19 (RIVG)
-
Rear motor inverter fail signal
Power switch on (IG), inverter operating normally
5.5 to 7.5
C-9 (RFIV) - C-19 (RIVG)
-
Rear motor inverter fail signal
Power switch on (IG), inverter not operating normally
2 to 3
C-10 (RIVA) - C-18 (RSG)
-
Rear motor V phase current
Power switch on (IG)
Approximately 0
C-12 (RIVB) - C-18 (RSG)
-
Rear motor V phase current
Power switch on (IG)
Approximately 0
C-11 (RIWA) - C-18 (RSG)
-
Rear motor W phase current
Power switch on (IG)
Approximately 0
C-13 (RIWB) - C-18 (RSG)
-
Rear motor W phase current
Power switch on (IG)
Approximately 0
C-14 (RSDN) - C-19 (RIVG)
-
Rear motor shutdown signal
Power switch on (IG), shift lever in the N position
0.2 to 0.7
C-14 (RSDN) - C-19 (RIVG)
-
Rear motor shutdown signal
Power switch on (IG), shift lever in the P position
5.1 to 13.6
C-15 (RUU) - C-19 (RIVG)
-
Rear motor switch U signal
Power switch on (IG)
Pulse generation
(Waveform 1)
C-16 (RWU) - C-19 (RIVG)
-
Rear motor switch W signal
Power switch on (IG)
Pulse generation
(Waveform 2)
C-17 (RVU) - C-19 (RIVG)
-
Rear motor switch V signal
Power switch on (IG)
Pulse generation
(Waveform 3)
B-33 (OVLMO) - A-18 (GCNV)
-
Boost converter overvoltage signal
Power switch on (IG), boost converter operating normally
5.3 to 7.7
B-33 (OVLMO) - A-18 (GCNV)
-
Boost converter overvoltage signal
Power switch on (IG), boost converter not operating normally
1.9 to 3.0
C-29 (OVHRO) - B-17 (GINV)
-
Motor inverter overvoltage signal
Power switch on (IG), inverter operating normally
5.5 to 7.5
C-29 (OVHRO) - B-17 (GINV)
-
Motor inverter overvoltage signal
Power switch on (IG), inverter not operating normally
2 to 3
C-31 (+BRr) - C-26 (GNDRr)
-
Power source for rear inverter
Power switch on (IG)
11 to 14
B-7 (MIT) - B-17 (GINV)
-
Motor inverter temperature
Power switch on (IG)
1.5 to 4.5
B-8 (MFIV) - B-17 (GINV)
-
Motor inverter fail signal
Power switch on (IG), inverter operating normally
5.5 to 7.5
B-8 (MFIV) - B-17 (GINV)
-
Motor inverter fail signal
Power switch on (IG), inverter not operating normally
2 to 3
B-9 (MIVA) - B-17 (GINV)
-
Motor V phase current
Power switch on (IG)
Approximately 0
B-11 (MIVB) - B-17 (GINV)
-
Motor V phase current
Power switch on (IG)
Approximately 0
B-10 (MIWA) - B-17 (GINV)
-
Motor W phase current
Power switch on (IG)
Approximately 0
B-12 (MIWB) - B-17 (GINV)
-
Motor W phase current
Power switch on (IG)
Approximately 0
B-13 (MSDN) - B-17 (GINV)
-
Motor shutdown signal
Power switch on (IG), shift lever in the N position
0.2 to 0.7
B-13 (MSDN) - B-17 (GINV)
-
Motor shutdown signal
Power switch on (IG), shift lever in the P position
5.1 to 13.6
B-14 (GUU) - B-17 (GINV)
-
Generator switch U signal
Power switch on (IG)
Pulse generation
(Waveform 4)
B-15 (GWU) - B-17 (GINV)
-
Generator switch W signal
Power switch on (IG)
Pulse generation
(Waveform 5)
B-16 (GVU) - B-17 (GINV)
-
Generator switch V signal
Power switch on (IG)
Pulse generation
(Waveform 6)
B-18 (GIT) - B-17 (GINV)
-
Generator temperature sensor
Power switch on (IG)
1.5 to 4.5
B-19 (GFIV) - B-17 (GINV)
-
Generator fail signal
Power switch on (IG), inverter operating normally
5.5 to 7.5
B-19 (GFIV) - B-17 (GINV)
-
Generator fail signal
Power switch on (IG), inverter not operating normally
2 to 3
B-20 (GIVA) - B-17 (GINV)
-
Generator V phase current
Power switch on (IG)
Approximately 0
B-22 (GIVB) - B-17 (GINV)
-
Generator V phase current
Power switch on (IG)
Approximately 0
B-21 (GIWA) - B-17 (GINV)
-
Generator W phase current
Power switch on (IG)
Approximately 0
B-23 (GIWB) - B-17 (GINV)
-
Generator W phase current
Power switch on (IG)
Approximately 0
B-24 (GSDN) - B-17 (GINV)
-
Generator shutdown signal
Power switch on (IG), shift lever in the N position
0.2 to 0.7
B-24 (GSDN) - B-17 (GINV)
-
Generator shutdown signal
Power switch on (IG), shift lever in the P position
5.1 to 13.6
B-25 (MUU) - B-17 (GINV)
-
Motor switch U signal
Power switch on (IG)
Pulse generation
(Waveform 7)
B-26 (MWU) - B-17 (GINV)
-
Motor switch W signal
Power switch on (IG)
Pulse generation
(Waveform 8)
B-27 (MVU) - B-17 (GINV)
-
Motor switch V signal
Power switch on (IG)
Pulse generation
(Waveform 9)
B-31 (VH) - B-17 (GINV)
-
Inverter capacitor voltage monitor
Power switch on (READY)
1.6 to 3.8
B-32 (OVHI) - B-17 (GINV)
-
Motor inverter overvoltage signal
Power switch on (IG), inverter operating normally
5.5 to 7.5
B-32 (OVHI) - B-17 (GINV)
-
Motor inverter overvoltage signal
Power switch on (IG), inverter not operating normally
2 to -3
B-35 (+BMG) - B-28 (GNDMG)
-
Power source for main inverter
Power switch on (IG)
11 to 14
A-10 (CPWM) - A-18 (GCNV)
-
Boost converter PWM switch signal
Power switch on (READY), parking brake on, shift lever in the D position, brake and accelerator pedals depressed
Pulse generation*
A-11 (CSDN) - A-18 (GCNV)
-
Boost converter shutdown signal
Power switch on (IG)
5.6 or higher
A-12 (VL) - A-18 (GCNV)
-
Boost converter input voltage
Power switch on (READY)
2.6 to 4.3
A-13 (OVL) - A-18 (GCNV)
-
Boost converter overvoltage signal
Power switch on (IG), boost converter operating normally
5.3 to 7.7
A-13 (OVL) - A-18 (GCNV)
-
Boost converter overvoltage signal
Power switch on (IG), boost converter not operating normally
1.9 to 3.0
A-14 (FCV) - A-18 (GCNV)
-
Boost converter fail signal
Power switch on (IG), boost converter operating normally
5.3 to 7.7
A-14 (FCV) - A-18 (GCNV)
-
Boost converter fail signal
Power switch on (IG), boost converter not operating normally
1.9 to 3.0
A-15 (IDH) - A-1 (GND1)
-
Blower motor for A/C operation inhibition request signal
Power switch on (IG), permission for blower motor operation requested
5 to 7
A-15 (IDH) - A-1 (GND1)
-
Blower motor for A/C operation inhibition request signal
Power switch on (IG), blower motor operation inhibition requested
2 to 4
A-16 (VLO) - A-1 (GND1)
-
DC/DC converter voltage switch signal
Power switch on (IG)
Pulse generation
(Waveform 10)
A-17 (SO) - A-1 (GND1)
-
Auxiliary battery voltage monitor
Power switch on (IG)
11 to 14
A-19 (CT) - A-18 (GCNV)
-
Boost converter temperature sensor
Power switch on (IG)
1.5 to 4.5
A-21 (HWT) - A-20 (HWTG)
-
Inverter coolant temperature sensor
Power switch on (IG)
0.5 to 4.8
A-26 (NODDI) - A-1 (GND1)
-
DC/DC converter operation monitor/stop request signal
DC/DC converter operating normally
5.3 to 6.7
A-26 (NODDI) - A-1 (GND1)
-
DC/DC converter operation monitor/stop request signal
DC/DC converter not operating normally
2.5 to 3.5
A-26 (NODDI) - A-1 (GND1)
-
DC/DC converter operation monitor/stop request signal
DC/DC converter ordered to stop
0.1 to 0.8
A-30 (OVHCO) - A-18 (GCNV)
-
Motor inverter overvoltage signal
Power switch on (IG), inverter operating normally
5.5 to 7.5
A-30 (OVHCO) - A-18 (GCNV)
-
Motor inverter overvoltage signal
Power switch on (IG), inverter not operating normally
2 to 3
A-32 (+BC) - A-28 (GNDC)
-
Power source for boost converter
Power switch on (IG)
11 to 14
A42-4 (+B2) - A-1 (GND1)
LG
MG ECU power source
Power switch on (IG)
11 to 14
A42-7 (+B) - A-1 (GND1)
P
MG ECU power source
Power switch on (IG)
11 to 14
A42-9 (MTH+) - A-1 (GND1)
B
Communication signal from MG to HV
Power switch on (IG)
Pulse generation
(Waveform 11)
A42-10 (MTH-) - A-1 (GND1)
W
Communication signal from MG to HV
Power switch on (IG)
Pulse generation
(Waveform 11)
A42-12 (HTM+) - A-1 (GND1)
B
Communication signal from HV to MG
Power switch on (IG)
Pulse generation
(Waveform 12)
A42-13 (HTM-) - A-1 (GND1)
W
Communication signal from HV to MG
Power switch on (IG)
Pulse generation
(Waveform 12)
A42-14 (NE) - A-1 (GND1)
B
Engine speed signal
Power switch on (READY) with engine running
Pulse generation*
A42-15 (REQ+) - A-1 (GND1)
B
Communication request signal
Power switch on (IG)
Pulse generation
(Waveform 13)
A42-16 (REQ-) - A-1 (GND1)
W
Communication request signal
Power switch on (IG)
Pulse generation
(Waveform 13)
A42-17 (CLK+) - A-1 (GND1)
B
Communication clock signal
Power switch on (IG)
Pulse generation
(Waveform 14)
A42-18 (CLK-) - A-1 (GND1)
W
Communication clock signal
Power switch on (IG)
Pulse generation
(Waveform 14)
A42-21 (RRF) - A42-22 (RRFG)
BR - G
Rear motor resolver signal
Rear motor resolver stopped or running
Pulse generation
(Waveform 15)
A42-29 (RSN) - A42-30 (RSNG)
L - R
Rear motor resolver signal
Rear motor resolver stopped or running
Pulse generation
(Waveform 15)
A42-11 (RCS) - A42-23 (RCSG)
W - Y
Rear motor resolver signal
Rear motor resolver stopped or running
Pulse generation
(Waveform 15)
A42-24 (GI) - A-1 (GND1)
W
GI signal
Power switch on (READY) with engine running
Pulse generation*
A42-26 (HSDN) - B-17 (GINV)
B
Emergency shutdown signal
Power switch on (IG)
Below 0.5
A42-33 (NODD) - A-1 (GND1)
W
DC/DC converter operation monitor/stop request signal
DC/DC converter operating normally
5.3 to 6.7
A42-33 (NODD) - A-1 (GND1)
W
DC/DC converter operation monitor/stop request signal
DC/DC converter not operating normally
2.5 to 3.5
A42-33 (NODD) - A-1 (GND1)
W
DC/DC converter operation monitor/stop request signal
DC/DC converter ordered to stop
0.1 to 0.8
A42-35 (SI) - A-1 (GND1)
LG
Auxiliary battery voltage monitor
Power switch on (IG)
11 to 14
B49-12 (GRF) - B49-22 (GRFG)
BR - G
Generator resolver signal
Generator resolver stopped or running
Pulse generation
(Waveform 16)
B49-11 (GSN) - B49-10 (GSNG)
L - R
Generator resolver signal
Generator resolver stopped or running
Pulse generation
(Waveform 16)
B49-9 (GCS) - B49-8 (GCSG)
W - Y
Generator resolver signal
Generator resolver stopped or running
Pulse generation
(Waveform 16)
B49-13 (MRF) - B49-23 (MRFG)
BR - G
Motor resolver signal
Motor resolver stopped or running
Pulse generation
(Waveform 17)
B49-21 (MSN) - B49-20 (MSNG)
L - R
Motor resolver signal
Motor resolver stopped or running
Pulse generation
(Waveform 17)
B49-19 (MCS) - B49-18 (MCSG)
W - Y
Motor resolver signal
Motor resolver stopped or running
Pulse generation
(Waveform 17)
*: Waveform cannot be measured because it is impossible to turn the power switch on (READY) with the inverter cover open.

Oscilloscope waveforms

HINT:
Oscilloscope waveform samples are provided here for informational purposes. Noise and fluttering waveforms have been omitted.



    A111608E01
  1. Waveform 1 (rear motor switch U signal)
    Item
    Contents
    Terminal
    RUU - RIVG
    Equipment Setting
    5 V/DIV., 100 μs./DIV.
    Condition
    Power switch on (IG)



  2. A111608E01
  3. Waveform 2 (rear motor switch W signal)
    Item
    Contents
    Terminal
    RWU - RIVG
    Equipment Setting
    5 V/DIV., 100 μs./DIV.
    Condition
    Power switch on (IG)



  4. A111608E01
  5. Waveform 3 (rear motor switch V signal)
    Item
    Contents
    Terminal
    RVU - RIVG
    Equipment Setting
    5 V/DIV., 100 μs./DIV.
    Condition
    Power switch on (IG)



  6. A111608E01
  7. Waveform 4 (generator switch U signal)
    Item
    Contents
    Terminal
    GUU - GINV
    Equipment Setting
    5 V/DIV., 100 μs./DIV.
    Condition
    Power switch on (IG)



  8. A111608E01
  9. Waveform 5 (generator switch W signal)
    Item
    Contents
    Terminal
    GWU - GINV
    Equipment Setting
    5 V/DIV., 100 μs./DIV.
    Condition
    Power switch on (IG)



  10. A111608E01
  11. Waveform 6 (generator switch V signal)
    Item
    Contents
    Terminal
    GVU - GINV
    Equipment Setting
    5 V/DIV., 100 μs./DIV.
    Condition
    Power switch on (IG)



  12. A111608E01
  13. Waveform 7 (motor switch U signal)
    Item
    Contents
    Terminal
    MUU - GINV
    Equipment Setting
    5 V/DIV., 100 μs./DIV.
    Condition
    Power switch on (IG)



  14. A111608E01
  15. Waveform 8 (motor switch W signal)
    Item
    Contents
    Terminal
    MWU - GINV
    Equipment Setting
    5 V/DIV., 100 μs./DIV.
    Condition
    Power switch on (IG)



  16. A111608E01
  17. Waveform 9 (motor switch V signal)
    Item
    Contents
    Terminal
    MVU - GINV
    Equipment Setting
    5 V/DIV., 100 μs./DIV.
    Condition
    Power switch on (IG)



  18. A111609E01
  19. Waveform 10 (DC/DC converter voltage switch signal)
    Item
    Contents
    Terminal
    VLO - GND1
    Equipment Setting
    5 V/DIV., 100 μs./DIV.
    Condition
    Power switch on (IG)



  20. A114530E01
  21. Waveform 11 (communication signal from MG ECU to hybrid vehicle control ECU)
    Item
    Contents
    Terminal
    CH1: MTH+ - GND1
    CH2: MTH- - GND1
    Equipment Setting
    1 V/DIV., 200 μs./DIV.
    Condition
    Power switch on (IG)

    HINT:
    The waveform will vary depending on the content of the digital communication (digital signal).



  22. A114529E01
  23. Waveform 12 (communication signal from hybrid vehicle control ECU to MG ECU)
    Item
    Contents
    Terminal
    CH1: HTM+ - GND1
    CH2: HTM- - GND1
    Equipment Setting
    1 V/DIV., 200 ms./DIV.
    Condition
    Power switch on (IG)

    HINT:
    The waveform will vary depending on the content of the digital communication (digital signal).



  24. A111605E01
  25. Waveform 13 (MG ECU communication request signal)
    Item
    Contents
    Terminal
    CH1: REQ+ - GND1
    CH2: REQ- - GND1
    Equipment Setting
    1 V/DIV., 1 ms./DIV.
    Condition
    Power switch on (IG)



  26. A111604E01
  27. Waveform 14 (MG ECU communication clock signal)
    Item
    Contents
    Terminal
    CH1: CLK+ - GND1
    CH2: CLK- - GND1
    Equipment Setting
    1 V/DIV., 1 μs./DIV.
    Condition
    Power switch on (IG)



  28. A111610E01
  29. Waveform 15 (rear motor resolver signal)
    Item
    Contents
    Terminal
    CH1: RRF - RRFG
    CH2: RSN - RSNG
    CH2: RCS - RCSG
    Equipment Setting
    CH1: 10 V/DIV., 1 ms./DIV.
    CH2, CH3: 5 V/DIV., 1 ms./DIV.
    Condition
    Resolver running

    HINT:
    Pulse cycle A becomes shorter as the rotor speed increases.



  30. A111610E01
  31. Waveform 16 (generator resolver signal)
    Item
    Contents
    Terminal
    CH1: GRF - GRFG
    CH2: GSN - GSNG
    CH2: GCS - GCSG
    Equipment Setting
    CH1: 10 V/DIV., 1 ms./DIV.
    CH2, CH3: 5 V/DIV., 1 ms./DIV.
    Condition
    Resolver running

    HINT:
    Pulse cycle A becomes shorter as the rotor speed increases.



  32. A111610E01
  33. Waveform 17 (motor resolver signal)
    Item
    Contents
    Terminal
    CH1: MRF - MRFG
    CH2: MSN - MSNG
    CH2: MCS - MCSG
    Equipment Setting
    CH1: 10 V/DIV., 1 ms./DIV.
    CH2, CH3: 5 V/DIV., 1 ms./DIV.
    Condition
    Resolver running

    HINT:
    Pulse cycle A becomes shorter as the rotor speed increases.