Home › HYBRID SYSTEM ยท P310 › HYBRID VEHICLE CONTROL › HYBRID CONTROL SYSTEM

HYBRID CONTROL SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

NOTICE:
  1. Some data list values may vary significantly if there are slight differences in the environment in which the vehicle is operating when measurements are obtained. Variations may also occur due to aging of the vehicle. Due to these considerations, it is not always possible to provide definite values to be used for judgment of malfunctions. It is possible that a malfunction may be present even if measured values are within the reference range.
  2. In the event of a problem with intricate symptoms, collect sample data from another vehicle of the same model operating under identical conditions in order to reach an overall judgment by comparing all the items in the data list.

HINT:
Using the Techstream to read the data list allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the data list information early in troubleshooting is one way to save diagnostic time.

  1. Connect the Techstream to the DLC3.

  2. Turn the power switch on (IG).

  3. Select the following menu items: Powertrain / Hybrid Control / Data List.

  4. Check the results by referring to the following table.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Engine Coolant Temp
    Engine coolant temperature/Min.: -40°F (-40°C), Max.: 284°F (140°C)
    After warming up: 176 to 212°F (80 to 100°C)
    -
    Engine Revolution
    Engine speed/Min.: 0 rpm, Max.: 16383.75 rpm
    Idling (INSPECTION MODE, P position, A/C OFF): 850 to 950 rpm
    -
    Vehicle Spd
    Vehicle speed/Min.: 0 MPH (0 km/h), Max.: 158 MPH (255 km/h)
    Vehicle stopped: 0 MPH (0 km/h)
    -
    Engine Run Time
    Elapsed time after starting engine/Min.: 0 s, Max.: 65,535 s
    -
    -
    +B
    Auxiliary battery voltage/Min.: 0 V, Max.: 65.535 V
    Constant: Auxiliary battery voltage +/-3 V
    -
    Accel Pedal Pos #1
    Accelerator pedal position sensor No. 1/Min.: 0%, Max.: 100%
    Accelerator pedal depressed: Changes with accelerator pedal pressure
    -
    Accel Pedal Pos #2
    Accelerator pedal position sensor No. 2/Min.: 0%, Max.: 100%
    Accelerator pedal depressed: Changes with accelerator pedal pressure
    -
    Ambient Temperature
    Ambient air temperature/Min.: -40°F (-40°C), Max.: 419°F (215°C)
    Power switch on (IG): Same as ambient air temperature
    -
    Intake Air Temperature
    Intake air temperature/Min.: -40°F (-40°C), Max.: 284°F (140°C)
    Constant: Same as ambient air temperature
    -
    DTC Clear Warm Up
    The number of times the engine is warmed up after clearing DTCs/Min.: 0, Max.: 255
    MIL OFF, engine coolant temperature increases from below 72°F (22°C) before starting the engine to above 158°F (70°C) after starting the engine: Increases once
    -
    DTC Clear Run Distance
    Drive distance after clearing DTCs/Min.: 0 mile (0 km), Max.: 40,723 mile (65,535 km)
    -
    -
    DTC Clear Min
    Elapsed time after clearing DTCs/Min.: 0 Min, Max.: 65,535 Min
    -
    -
    MIL on Run Distance
    MIL ON run distance/Min.: 0 mile (0 km), Max.: 40,723 mile (65,535 km)
    Distance after DTC detected
    -
    MIL on Engine Run Time
    MIL ON engine run time/
    Min.: 0 Min
    Max.: 65.535 Min
    Time after DTC detected
    -
    MIL Status
    MIL status/ON or OFF
    MIL ON: ON
    Constant ON: Repair in accordance with detected DTCs
    Model Code
    Model code
    -
    Identifying model code:
    MHU48
    Engine Code
    Engine code
    -
    Identifying engine type:
    3MZFE
    ECU Code
    ECU code
    48320
    -
    Destination
    Destination
    -
    Identifying destination:
    A (USA)
    Motor(MG2) Revolution
    MG2 revolution/Min.: -16,383 rpm, Max.: 16,383 rpm
    -
    -
    Motor(MG2) Torq
    MG2 torque/Min.: -500 N*m, Max.: 500 N*m
    -
    -
    Rear Motor Revolution
    MGR revolution/Min.: -16,383 rpm, Max.: 16,383 rpm
    -
    -
    Rear Motor Torq
    MGR torque/Min.: -500 N*m, Max.: 500 N*m
    -
    -
    M(MG2) Trq Exec Val
    MG2 torque execution value/Min.: -512 Nm, Max.: 508 Nm
    After full-load acceleration with READY light ON and engine stopped: Less than +-20% of Motor (MG2) Torq
    -
    Rear Mtr Trq Exec Val
    MGR torque execution value/Min.: -512 Nm, Max.: 508 Nm
    After full-load acceleration with READY light ON and engine stopped: Less than +-20% of Rear Motor Torq
    -
    Generator(MG1) Rev
    MG1 revolution/Min.: -16,383 rpm, Max.: 16,383 rpm
    -
    -
    Generator(MG1) Torq
    MG1 torque/Min.: -500 N*m, Max.: 500 N*m
    -
    -
    G(MG1) Trq Exec Val
    MG1 torque execution value/Min.: -512 Nm, Max.: 508 Nm
    After full-load acceleration with READY light ON and engine stopped: Less than +-20% of Generator (MG1) Torq
    -
    Regenerative Brake Torq
    Regenerative braking execution torque/Min.: 0 N*m, Max.: 1,020 N*m
    -
    -
    Rqst Regen Brake Torq
    Regenerative braking request torque/Min.: 0 N*m, Max.: 1,020 N*m
    Vehicle speed 19 MPH (30 km/h) and master cylinder hydraulic pressure -200 N*m: Changes with brake pedal pressure
    -
    Rear Regen Brake Torq
    Regenerative braking execution torque/Min.: 0 N*m, Max.: 1,020 N*m
    -
    -
    R Rqst Regen Brk Torq
    Regenerative braking execution torque/Min.: 0 N*m, Max.: 1,020 N*m
    Vehicle speed 19 MPH (30 km/h) and master cylinder hydraulic pressure -200 N*m: Changes with brake pedal pressure
    -
    Inverter Temp-(MG1)
    Generator inverter temperature/Min.: -58°F (-50°C), Max.: 401°F (205°C)
    1. Undisturbed for 1 day at 77°F (25°C): 77°F (25°C)
    2. Street driving: 77 to 176°F (25 to 80°C)
    1. If the value is -58°F (-50°C): short to +B in sensor circuit
    2. If the value is 401°F (205°C): Open or short to GND in sensor circuit
    Inverter Temp-(MG2)
    Motor inverter temperature/Min.: -58°F (-50°C), Max.: 401°F (205°C)
    1. Undisturbed for 1 day at 77°F (25°C): 77°F (25°C)
    2. Street driving: 77 to 176°F (25 to 80°C)
    1. If the value is -58°F (-50°C): short to +B in sensor circuit
    2. If the value is 401°F (205°C): Open or short to GND in sensor circuit
    Rear Inverter Temp
    Rear motor inverter temperature/Min.: -58°F (-50°C), Max.: 401°F (205°C)
    1. Undisturbed for 1 day at 77°F (25°C): 77°F (25°C)
    2. Street driving: 77 to 176°F (25 to 80°C)
    1. If the value is -58°F (-50°C): short to +B in sensor circuit
    2. If the value is 401°F (205°C): Open or short to GND in sensor circuit
    Motor Temp No2
    MG2 temperature/Min.: -58°F (-50°C), Max.: 401°F (205°C)
    1. Undisturbed for 1 day at 77°F (25°C): 77°F (25°C)
    2. Street driving: 77 to 212°F (25 to 100°C)
    1. If the value is -58°F (-50°C): short to +B in sensor circuit
    2. If the value is 401°F (205°C): Open or short to GND in sensor circuit
    Motor Temp No1
    MG1 temperature/Min.: -58°F (-50°C), Max.: 401°F (205°C)
    1. Undisturbed for 1 day at 77°F (25°C): 77°F (25°C)
    2. Street driving: 77 to 194°F (25 to 90°C)
    1. If the value is -58°F (-50°C): short to +B in sensor circuit
    2. If the value is 401°F (205°C): Open or short to GND in sensor circuit
    Rear Motor Temp
    MGR temperature/Min.: -58°F (-50°C), Max.: 401°F (205°C)
    1. Undisturbed for 1 day at 77°F (25°C): 77°F (25°C)
    2. Street driving: 77 to 176°F (25 to 80°C)
    1. If the value is -58°F (-50°C): short to +B in sensor circuit
    2. If the value is 401°F (205°C): Open or short to GND in sensor circuit
    Rear Torque Ratio
    Rear Torque Ratio/Min.: 0%, Max.: 100%
    -
    -
    Converter Temperature
    Boost converter temperature/Min.: -58°F (-50°C), Max.: 401°F (205°C)
    1. Undisturbed for 1 day at 77°F (25°C): 77°F (25°C)
    2. Street driving: 77 to 140°F (25 to 60°C)
    1. If the value is -58°F (-50°C): short to +B in sensor circuit
    2. If the value is 401°F (205°C): Open or short to GND in sensor circuit
    Accelerator Degree
    Accelerator pedal depressed angle/Min.: 0%, Max.: 100%
    Accelerator pedal depressed: Changes with accelerator pedal pressure
    -
    Request Power
    Request engine power/Min.: 0 W, Max.: 320000 W
    -
    -
    Target Engine Rev
    Target engine speed/Min.: 0 rpm, Max.: 8,000 rpm
    -
    -
    Engine Spd
    Engine speed/Min.: 0 rpm, Max.: 8,000 rpm
    Idling (INSPECTION MODE, P position, A/C OFF): 850 to 950 rpm
    -
    Vehicle Speed (Resolver)
    Resolver/Min.: -159 MPH (-256 km/h), Max.: 158 MPH (254 km/h)
    Same as vehicle speed
    -
    Master Cylinder Ctrl Trq
    Braking torque that is equivalent to master cylinder hydraulic pressure/Min.: -2,040 N*m, Max.: 0 N*m
    Brake pedal depressed:
    Changes with brake pedal pressure
    -
    State of Charge
    Battery state of charge/Min.: 0%, Max.: 100%
    Constant: 0 to 100%
    -
    WOUT Control Power
    Discharge control power value/Min.: 0 W, Max.: 81,600 W
    36,000 W or less
    -
    WIN Control Power
    Charge control power value/Min.: -40,800 W, Max.: 0 W
    -36,000 W or more
    -
    Discharge Rqst to SOC
    Discharge request to adjust SOC/Min.: -20,480 W, Max.: 20,320 W
    1. Uniform on-board charging: 4,400 W
    2. Usually: 0 W
    -
    Power Resource VB
    HV battery voltage/Min.: 0 V, Max.: 510 V
    READY light ON and P position: 240 to 400 V
    -
    Power Resource IB
    HV battery current/Min.: -256 A, Max.: 254 A
    -
    -
    VL-Voltage before boosting
    High voltage before it is boosted/Min.: 0 V, Max.: 510 V
    READY ON: Almost the same as the HV battery voltage
    1. If the value is 0 V: Open or short to GND in sensor circuit
    2. If the value is 510 V: short to +B in sensor circuit
    VH-Voltage after boosting
    High voltage after it is boosted/Min.: 0 V, Max.: 765 V
    Engine revving up in the P position: Between HV battery voltage and 650 V
    1. If the value is 0 V: Open or short to GND in sensor circuit
    2. If the value is 765 V: short to +B in sensor circuit
    Boost Ratio
    Boost ratio/Min.: 0%, Max.: 100%
    The pre-boost and the post boost voltages are equal: 0 to 10%
    -
    Drive Condition ID
    Drive condition ID/Min.: 0, Max.: 6
    1. Engine stopped: 0
    2. Engine about to be stopped: 1
    3. Engine about to be started: 2
    4. Engine operated or operating: 3
    5. Generating or loading movement: 4
    6. Revving in the P position: 6
    -
    Shift Sensor Shift Pos
    Shift lever position
    P, R, N, D or B
    -
    Crank Position
    Crankshaft position/Min.: -90 deg., Max.: 90 deg.
    -
    -
    A/C Consumption Pwr
    A/C consumption power/Min.: 0 kW, Max.: 5 kW
    -
    -
    Loading Condition
    Driving condition
    1. Generator load: MG1
    2. Motor load: MG2
    -
    Driving Pattern 1 to 3
    Driving pattern/
    Lo Spd, MID Spd, or MID HI
    -
    -
    Short Wave Highest Val
    Waveform voltage in leak detection circuit/Min.: 0 V, Max.: 5 V
    Left for 2 Minutes with power switch on (READY), and pre-boost and post-boost voltages are equal: 4 V or more
    -
    MG1 Control Mode
    MG1 control mode
    -
    -
    MG1 Carrier Frequency
    MG1 carrier frequency/10 kHz / 5 kHz
    -
    -
    MG2 Control Mode
    MG2 control mode
    -
    -
    MG2 Carrier Frequency
    MG2 carrier frequency/5 kHz / 2.5 kHz / 1.25 kHz
    -
    -
    Type of ECU
    Type of ECU
    -
    Identifying ECU type:
    HV ECU
    Num of Current Code
    The number of current DTCs/Min.: 0, Max.: 255
    -
    -
    Num of History Code
    The number of history DTCs/Min.: 0, Max.: 255
    -
    -
    Check Mode
    Check mode/
    ON or OFF
    Check mode ON

    Rmg Control Mode
    MGR control mode
    -
    -
    Rmg Carrier Frequency
    MGR carrier frequency/5 kHz / 2.5 kHz / 1.25 kHz
    -
    -
    Shift Sensor SW - P
    Shift lever position sensor/ON or OFF
    P position: ON
    Except P position: OFF
    -
    Shift Sensor SW - R
    Shift lever position sensor/ON or OFF
    R position: ON
    Except R position: OFF
    -
    Shift Sensor SW - N
    Shift lever position sensor/ON or OFF
    N position: ON
    Except N position: OFF
    -
    Shift Sensor SW - D
    Shift lever position sensor/ON or OFF
    D position: ON
    Except D position: OFF
    -
    Shift Sensor SW - B
    Shift lever position sensor/ON or OFF
    B position: ON
    Except B position: OFF
    -
    Shift Sensor SW - FD
    Shift lever position sensor/ON or OFF
    D or B position: ON
    Except D or B position: OFF
    -
    Shift Sensor SW - RV
    Shift lever position sensor/ON or OFF
    R position: ON
    Except R position: OFF
    -
    Shift Sensor SW - MJ
    Shift lever position sensor/ON or OFF
    P, R, N, D or B position: ON
    -
    Calculate Load
    Calculate load/Min.: 0%, Max.: 100%
    1. Idling (INSPECTION MODE): 11 to 22%
    2. Driving (2,500 rpm): 12.1 to 18.2%
    -
    Throttle Position
    Throttle position sensor/Min.: 0%, Max.: 100%
    Throttle valve fully closed: 10 to 24%
    Throttle valve fully open: 64 to 96%
    -
    L-Tmp Start Judging
    Time of low temperature start judging/Min.: 0, Max.: 65535
    -
    -
    L-Tmp Start Accumulate
    Low temperature starting accumulation time/Min.: 0, Max.: 67107840
    -
    -
    Engine Stop Request
    Engine stop request/NO or RQST
    Requesting engine stop: RQST
    -
    Engine Idling Request
    Engine idling request/NO or RQST
    Requesting idle: RQST
    -
    Main Batt Charging Rqst
    HV battery charging request/NO or RQST
    Requesting HV battery charging: RQST
    -
    HCAC OBD Request
    HCAC OBD Request / NO or RQST
    Requesting HCAC OBD: RQST
    -
    Aircon Request
    Engine starting request from A/C amplifier/NO or RQST
    Requesting engine start from A/C amplifier: RQST
    -
    Engine Warming Up Rqst
    Engine warm-up request/NO or RQST
    Requesting engine warm-up: RQST
    -
    System Precharge Relay Status - (SMRP)
    Operating condition of SMR1/ON or OFF
    Power switch on (READY): OFF
    -
    System Main Relay Status - SMRB
    Operating condition of SMR2/ON or OFF
    Power switch on (READY): ON
    -
    System Main Relay Status - SMRG
    Operating condition of SMR3/ON or OFF
    Power switch on (READY): ON
    -
    MG1 Gate Status
    MG1 gate status/ON or OFF
    Shutting down generator inverter: ON
    -
    MG2 Gate Status
    MG2 gate status/ON or OFF
    Shutting down motor inverter: ON
    -
    Converter Gate Status
    Boost converter gate status/ON or OFF
    Shutting down boost converter: ON
    -
    Aircon Gate Status
    A/C gate status:
    ON or OFF
    Shutting down A/C inverter: ON
    -
    Shutdown (Rear)
    MGR gate status/ON or OFF
    Shutting down rear motor inverter: ON
    -
    Converter Carrier Freq
    Converter Carrier Frequency/10 kHz / 5 kHz
    -
    -
    Complete Parts Monitor
    Complete Parts Monitor/
    Not Avl or Avail
    -
    -
    Component Monitor ENA
    Comprehensive Component
    Monitor ENA/
    Unable or Enable
    -
    -
    Component Monitor CMPL
    Comprehensive Component
    Monitor CMPL/
    Compl or Incmpl
    -
    -
    Battery State of Charge
    Battery state of charge/Min.: 0%, Max.: 100%
    -
    -
    Delta SOC
    Difference between maximum and Minimum values of SOC/Min.: 0%, Max.: 100%
    READY light ON, engine stopped and no electrical load: 0 to 60%
    -
    Batt Pack Current Val
    Current value of battery pack/Min.: -327.68 A, Max.: 327.67 A
    -Immediately after a full-load acceleration with the engine stopped: Maximum 190 A (room temperature)
    -Shifting into N position 1 second after engine automatically started in the P position with engine stopped, headlights ON, A/C fan speed high, and READY light ON: Maximum 30 A
    -
    VMF Fan Motor Voltage1 to 3
    Battery blower motor monitoring voltage/Min.: 0 V, Max.: 25.4 V
    Fan mode 1 with READY light ON and P position: 2.0 to 2.6 V
    -
    Auxiliary Battery Vol
    Auxiliary battery voltage/ Min.: 0 V, Max.: 25.4 V
    Equivalent to auxiliary battery voltage
    -
    Charge Control Value
    Charge control wattage/ Min.: -64 kW, Max.: 63.5 kW
    -33 kW or more
    -
    Discharge Control Value
    Discharge control wattage/Min.: -64 kW, Max.: 63.5 kW
    36 kW or less
    -
    Cooling Fan Mode1 to 3
    Battery blower motor actuation mode/Min.: 0, Max.: 6
    Stopped: 0
    Low to high speed actuation: 1 to 6
    -
    ECU Control Mode
    ECU control mode/Min.: 0, Max.: 4
    -
    -
    Standby Blower Request
    Battery blower motor stop control request (standby blower)/ON or OFF
    ON/OFF
    -
    Temp of Batt TB 1 to 8
    Temperature of HV battery/Min.: -557.824°F (-327.68°C), Max.: 621.806°F (327.67°C)
    Undisturbed for 1 day: Same as ambient air temperature
    -
    Battery Block Num
    The number of battery blocks/Min.: 0, Max.: 255
    Always: 15
    -
    Batt Block Minimum Vol
    Battery block Minimum voltage/Min.: -327.68 V, Max.: 327.67 V
    SOC 55 to 60%: 16 V or more
    -
    Minimum Batt Block No
    Battery block number with Minimum voltage
    One of numbers 1 to 15
    -
    Batt Block Max Vol
    Battery block maximum voltage/Min.: -327.68 V, Max.: 327.67 V
    SOC 55 to 60%: 31 V or less
    -
    Max Battery Block No
    Battery block number with maximum voltage
    One of numbers 1 to 15
    -
    Battery Block Vol -V01 to 15
    Battery block voltage/Min.: -327.68 V, Max.: 327.67 V
    SOC 60%: 16 to 27 V
    -
    Internal Resistance R01 to 15
    Internal resistance of each battery block/Min.: 0 , Max.: 0.255
    Always: 0.01 to 0.1
    -
    Battery Low Time
    Battery low time/Min.: 0, Max.: 65,535
    -
    -
    DC Inhibit Time
    DC inhibit time/Min.: 0, Max.: 65,535
    -
    -
    Battery too High Time
    Battery too high time/Min.: 0, Max.: 65,535
    -
    -
    Hot Temperature Time
    Hot temperature time/Min.: 0, Max.: 65,535
    -
    -


ACTIVE TEST

HINT:
Using the Techstream to perform active tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing active tests early in troubleshooting is one way to save diagnostic time. Data list information can be displayed while performing active tests.

NOTICE:
It is necessary to use caution, because if the tester DLC connector becomes disconnected or if a communication error occurs during an active test, the vehicle could become inoperative (the READY light may go off).

  1. Connect the Techstream to the DLC3.

  2. Turn the power switch on (IG) and turn the Techstream on.

  3. Enter the following menus: Powertrain / Hybrid Control / Active Test.

  4. According to the display on the Techstream, perform the appropriate active test.

    Tester Display
    Test Part
    Control Range
    Test Details
    Test Condition
    Forcible Stop of Inverter Drive
    To determine if there is an internal leak in the inverter or the hybrid vehicle control ECU
    ON / OFF
    Keeps the inverter power transistor actuation signal ON
    Power switch on (IG), shift lever in the P position, HV system normal, inverter actuation not being forcibly interrupted, during shutdown, and other active tests not being done
    Compression Test *1
    To crank the engine continuously in order to measure the compression
    ON / OFF
    Allows the engine to continue cranking by activating MG1 continuously
    Power switch on (IG), HV system normal, not in cranking mode, and other active tests not being done
    Activate the Water Pump
    To activate the water pump continuously
    ON / OFF
    Activates the hybrid vehicle water pump continuously
    Power switch on (IG), HV system normal, not in inspection mode, and other active tests not being done
    Driving the Battery Cooling Fan
    To check operation of the cooling fan and if there is sufficient air flow
    0 to 6
    Stops the cooling fan or changes air volume mode
    -
    Connect the TC and TE1
    Batch display of warnings on combination meter
    ON / OFF
    TC terminal can be switched ON/OFF
    Power switch on (IG), HV system is normal

    NOTICE:
    *1: The Techstream will display a communication error and the vehicle READY light will turn off when the active test is completed. If the tester will be used on the vehicle again, turn the vehicle power switch off and then on (READY) again and restart the tester.