Home › General › INTRODUCTION › WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS
BM3160E _V1 General _021869 INTRODUCTION _0112095 WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS F

INTRODUCTION  WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS  WHEEL ALIGNMENT STANDARD  


NOTICE:

If a wheel alignment has been performed, or if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:

Perform zero point calibration of the yaw rate and acceleration sensor.



MEASURE VEHICLE HEIGHT


NOTICE:
·

Before inspecting the wheel alignment, adjust the vehicle height to the specified value.

·

Be sure to perform measurement on a level surface.

·

If it is necessary to go under the vehicle for measurement, confirm that the parking brake is applied and the vehicle is secured with chocks.

·

Inspect while the vehicle is unloaded.

·

The standard value shown here is a value that is used for performing a wheel alignment and does not indicate the height of an actual vehicle.



a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.
C293036
0.833,1.115 1,1.344 0.167,0.229 10 false A 2.417,1.177 2.667,1.448 0.25,0.271 10 false B 0.823,3.917 1,4.167 0.177,0.25 10 false C 2.406,3.958 2.583,4.177 0.177,0.219 10 false D

Measure the vehicle height.

Measurement Points:

A: Ground clearance of front wheel center


B: Ground clearance of front lower suspension arm bushing set bolt center


C: Ground clearance of rear wheel center


D: Ground clearance of rear No. 2 suspension arm set bolt center


Vehicle Height (Unloaded Vehicle):
Front A - B Rear C - D
110.8 mm (4.36 in.) 44.0 mm (1.73 in.)




FRONT WHEEL ALIGNMENT


a.

INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION

NOTICE:

Inspect while the vehicle is unloaded.


i.
C132440
2.396,1.104 2.51,0.823 2.51,0.823 2.74,0.823 false 0.604,0.708 1.031,0.708 1.031,0.708 1.031,1.458 false 2.76,0.729 2.99,0.906 0.229,0.177 10 false *b 0.448,0.604 0.688,0.781 0.24,0.177 10 false *a
*a Turning Radius Gauge
*b Camber-caster-kingpin Gauge


Install a camber-caster-kingpin gauge and place the front wheels on the center of a turning radius gauge.


ii.

Inspect the camber, caster and steering axis inclination.

Camber (Unloaded Vehicle):
Camber Inclination Right-left Difference
-0.55° +/- 0.75° (-0°33' +/- 0°45') 0.75° (0°45') or less


Caster (Unloaded Vehicle):
Caster Inclination Right-left Difference
2.66° +/- 0.75° (2°40' +/- 0°45') 0.75° (0°45') or less


Steering Axis Inclination (Unloaded Vehicle):
Steering Axis Inclination Reference
10.83° (10°50')




b.

INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.


i.

Bounce the vehicle up and down at the corners to stabilize the suspension.


ii.

Release the parking brake and move the shift lever to N.


iii.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step C)


iv.
C188968
0.833,0.583 0.833,1.115 false 1.365,0.583 1.365,0.99 1.365,0.99 0.833,0.99 false 2.521,1.333 2.521,1.667 false 0.74,1.135 0.917,1.302 0.177,0.167 10 *a 2.427,1.698 2.604,1.854 0.177,0.156 10 *b
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).


v.

Slowly push the vehicle straight ahead to cause the front wheels to rotate 180°. Use the front tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step C again.



vi.
C188969
0.646,1.271 0.646,1.635 false 1.917,0.542 2.052,0.698 0.135,0.156 10 C 3.073,0.552 3.208,0.708 0.135,0.156 10 D 2.5,0.719 2.635,0.875 0.135,0.156 10 A 2.51,1.542 2.646,1.698 0.135,0.156 10 B 0.563,1.656 0.74,1.813 0.177,0.156 10 *a
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the wheels (dimension A).

Toe-in (Unloaded Vehicle):
Specified Condition
C + D: 0.08° +/- 0.17° (0°05' +/- 0°10')
B - A: 1.0 +/- 2.0 mm (0.0394 +/- 0.0787 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it at the steering rack ends.



c.
C132439
0.863,0.204 1.036,0.381 0.173,0.177 10 *b 0.538,0.204 0.713,0.381 0.176,0.177 10 *a 2.397,0.204 2.57,0.381 0.173,0.177 10 *b 2.725,0.204 2.901,0.381 0.176,0.177 10 *a
*a Inside
*b Outside
V100135

Front of the Vehicle


INSPECT WHEEL ANGLE

i.

Put tread center marks on the rearmost points of a turning radius gauge.


ii.

Turn the steering wheel fully to the left and right and measure the turning angle.

NOTICE:

Inspect while the vehicle is unloaded.


Wheel Turning Angle (Unloaded Vehicle):
Inside Wheel Outside Wheel
35.76° +/- 1.50° (35°46' +/- 1°30' ) 31.24° (31°14')


If the right and left inside wheel angles differ from the specified value, check and adjust the right and left steering rack end lengths.





REAR WHEEL ALIGNMENT


a.
C107736
2.052,1.26 2.375,1.26 false 2.406,1.167 2.656,1.385 0.25,0.219 10 *a
*a Camber-caster-kingpin Gauge


INSPECT CAMBER

NOTICE:

Inspect while the vehicle is unloaded.


i.

Install a camber-caster-kingpin gauge.


ii.

Inspect the camber.

Camber (Unloaded Vehicle):
Camber Inclination Right-left Difference
-0.51° +/- 0.75°(-0°31' +/- 0°45') 0.75°(0°45') or less


HINT:

Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.




b.

INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.


i.

Bounce the vehicle up and down at the corners to stabilize the suspension.


ii.

Release the parking brake and move the shift lever to N.


iii.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


iv.
C188968
0.83,0.579 0.83,1.114 false 1.361,0.579 1.361,0.992 1.361,0.992 0.83,0.992 false 0.739,1.134 0.912,1.302 0.173,0.168 10 *a 2.432,1.697 2.607,1.858 0.176,0.161 10 *b 2.522,1.33 2.522,1.671 false
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).


v.

Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from step A again.



vi.
C301346
0.635,1.635 0.635,1.167 false 0.563,1.688 0.875,1.844 0.313,0.156 10 false *a 2.469,0.573 2.625,0.771 0.156,0.198 10 false A 2.5,1.667 2.656,1.865 0.156,0.198 10 false B 1.844,0.396 2,0.594 0.156,0.198 10 false C 3.156,0.385 3.313,0.583 0.156,0.198 10 false D
*a Dimension A
V100135

Front of the Vehicle


Measure the distance between the tread center marks on the front of the rear wheels (dimension A).

Toe-in (Unloaded Vehicle):
Specified Condition
C + D: -0.08° +/- 0.17° (-0°05' +/- 0°10')
B - A: -1.0 +/- 2.0 mm (-0.0394 +/- 0.0787 in.)


HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, adjust it by following the procedures below.