Home › Vehicle Exterior › BODY PANEL › FRONT BODY PILLAR › 2013.12–2016.11
BM3160E _01 Vehicle Exterior _021870 BODY WELD POINT _0112107 FRONT BODY PILLAR F

BODY WELD POINT  FRONT BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS  


K110866

With the cowl top side panel removed.


REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts
K108829

Cut Location


REMOVAL POINT
1.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)

2.

*a indicates welds to remove for easier removal.


K110867C01
0.146,8.563 0.458,8.719 0.313,0.156 10 false *b 4.771,0.833 6.302,1.031 1.531,0.198 10 false 130 (5.12)
*b mm (in.) - -


K110868

K110906C01
0.135,8.573 0.448,8.729 0.313,0.156 10 false *c 1.281,1.979 2.656,2.177 1.375,0.198 10 false 70 (2.76)
*c mm (in.) - -


INSTALLATION


Symbol meaning
K108818

Remove Weld Points
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108830

Fillet Weld
K108831

Butt Weld
K108834

Body Sealer


Weld work for 980 MPa ultra high strength steel:

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)


*a: When welding 2 panels together including 980 MPa ultra high strength steel.

Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas


*b: When welding more than 3 panels together including 980 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas


NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


4.

Follow the welding conditions when welding *a and *b to assure sufficient weld strength. (See the introduction)

5.

When welding *c, make a hole on a new part for plug welding and weld the panel with the panel behind completely.

6.

Divide a new part of front body pillar upper reinforcement in to *d and *e at the weld points. After welding the *d to the vehicle side, install the *e.

7.

After welding the front body pillar sub-assembly inner to the vehicle side, install the front body pillar reinforce sub-assembly lower.

8.

After welding the front body pillar reinforce sub-assembly lower to the vehicle side, install the front body pillar outer and front fender bracket rear.

9.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

10.

After welding, apply body sealer to the corresponding parts. (See the painting / coating)

11.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K110869C01
2,1.75 2.198,1.75 2.198,1.75 2.469,2.01 false 3.833,3.063 3.667,3.063 3.667,3.063 3.167,3.25 false 3.885,4.458 3.719,4.458 3.719,4.458 3.365,4.146 false 1.844,1.688 2.156,1.885 0.313,0.198 10 false *1 3.865,2.99 4.177,3.188 0.313,0.198 10 false *d 3.917,4.385 4.229,4.583 0.313,0.198 10 false *e
*1 FRONT BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER - -


K110870C01
1.646,1.802 1.146,0.813 1.146,0.813 1.01,0.813 false 0.854,0.74 1.167,0.938 0.313,0.198 10 false *2 5.531,6.615 6.906,6.813 1.375,0.198 10 false 15 (0.59) 1.688,8.521 3.063,8.719 1.375,0.198 10 false 10 (0.39) 0.188,8.542 0.5,8.74 0.313,0.198 10 false *f
*2 FRONT BODY PILLAR SUB-ASSEMBLY INNER - -
*a Ultra High Strength Steel Welding Point *f mm (in.)


K110871C01
0.5,0.719 0.646,0.719 0.646,0.719 1.448,1.583 false 1.823,2.438 2.5,2.167 2.5,2.167 2.635,2.167 false 1.667,6.583 1.958,6.917 1.958,6.917 2.083,6.917 false 0.354,0.635 0.667,0.833 0.313,0.198 10 false *1 2.667,2.083 2.979,2.281 0.313,0.198 10 false *d 2.104,6.833 2.417,7.031 0.313,0.198 10 false *e 0.167,8.552 0.479,8.75 0.313,0.198 10 false *g 6.219,3.344 6.813,3.542 0.594,0.198 10 false 15 (0.59) 3.885,8.656 5.25,8.823 1.365,0.167 10 false 22 (0.87)
*1 FRONT BODY PILLAR REINFORCE SUB-ASSEMBLY LOWER - -
*g mm (in.) - -


K110872C01
4.625,1.813 4.26,1.104 4.26,1.104 4.125,1.104 false 4.302,5.594 4.49,5.594 4.49,5.594 4.625,6.635 false 3.958,1.021 4.271,1.219 0.313,0.198 10 false *3 4.146,5.521 4.458,5.719 0.313,0.198 10 false *4
*3 FRONT BODY PILLAR OUTER *4 FRONT FENDER BRACKET REAR
*b Ultra High Strength Steel Welding Point - -


K110873