Home › Vehicle Exterior › BODY PANEL › CENTER BODY PILLAR
BM3160E _01 Vehicle Exterior _021870 BODY WELD POINT _0112108 CENTER BODY PILLAR F

BODY WELD POINT  CENTER BODY PILLAR  CUT AND JOIN REPLACEMENT SECTIONS  


K110874

REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts
K108829

Cut Location


REMOVAL POINT
1.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)

2.

*a is reused.

3.

Remove the remaining foamed sealing material from the vehicles side.


K110875
1.375,0.979 1.031,0.635 1.031,0.635 0.927,0.635 false 3.5,5.24 4.292,5.688 4.292,5.688 4.427,5.688 false 1.552,5.719 1.698,5.719 1.698,5.719 2.406,5.271 false 0.781,0.531 1.094,0.688 0.313,0.156 10 false *a 0.156,8.615 0.469,8.771 0.313,0.156 10 false *c 2.417,0.323 3.792,0.521 1.375,0.198 10 false 20 (0.79) 0.583,1.458 2.115,1.656 1.531,0.198 10 false 220 (8.66) 2.177,1.385 3.865,1.583 1.688,0.198 10 false 320 (12.60) 1.583,7.521 3.115,7.719 1.531,0.198 10 false 150 (5.91) 4.646,7.479 6.021,7.677 1.375,0.198 10 false 90 (3.54) 1.406,5.625 1.719,5.823 0.313,0.198 10 false *b 4.448,5.625 4.76,5.823 0.313,0.198 10 false *b
*a Reused *b Foamed Sealing Material
*c mm (in.) - -


K110876
0.135,8.625 0.448,8.781 0.313,0.156 10 false *c 2.323,1.583 4.01,1.781 1.688,0.198 10 false 620 (24.41) 1.969,3.25 3.5,3.448 1.531,0.198 10 false 100 (3.94) 5,3.375 6.531,3.573 1.531,0.198 10 false 100 (3.94) 0.698,5.083 2.229,5.281 1.531,0.198 10 false 200 (7.87) 5.896,5.188 7.031,5.396 1.135,0.208 10 false 125 (4.92) 4.156,7.656 5.531,7.854 1.375,0.198 10 false 70 (2.76)
*c mm (in.) - -


INSTALLATION


Symbol meaning
K108818

Remove Weld Points
K108823

Plug Weld
K108827

Cut and Join Location
K108831

Butt Weld


Weld work for 980 MPa ultra high strength steel:

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)


*a: When welding 2 panels together including 980 MPa ultra high strength steel.

Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas


*b: When welding more than 3 panels together including 980 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas


NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Follow the welding conditions when welding *a and *b to assure sufficient weld strength. (See the introduction)

5.

After welding the MO.2 inner pillar sub-assembly to the vehicle side, install the center body pillar sub-assembly.

6.

After welding the center body pillar sub-assembly to the vehicle side, install the rear body front outside panel and *d.

7.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

8.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K110877
3.531,2.656 4,2.427 4,2.427 4.115,2.427 false 4.156,2.354 4.469,2.51 0.313,0.156 10 false *1 0.188,8.615 0.5,8.771 0.313,0.156 10 false *c 4.063,1.438 5.594,1.635 1.531,0.198 10 false 125 (4.92) 4.042,3.521 5.417,3.719 1.375,0.198 10 false 70 (2.76) 2.052,5.875 3.583,6.073 1.531,0.198 10 false 200 (7.87) 2.083,7.635 3.615,7.833 1.531,0.198 10 false 100 (3.94) 4.354,7.656 5.885,7.854 1.531,0.198 10 false 100 (3.94)
*1 NO.2 INNER PILLAR SUB-ASSEMBLY - -
*c mm (in.) - -


K110878

K110879
2.573,5.698 2.698,4.677 2.698,4.677 2.781,4.677 false 5.25,6.292 5.021,5.708 5.021,5.708 4.927,5.708 false 4.344,3.833 4.25,3.833 4.25,3.833 3.948,3.25 false 4.385,3.76 4.698,3.917 0.313,0.156 10 false *2 2.833,4.594 3.146,4.75 0.313,0.156 10 false *3 4.771,5.625 5.083,5.823 0.313,0.198 10 false *d
*2 CENTER BODY PILLAR SUB-ASSEMBLY *3 REAR BODY FRONT OUTSIDE PANEL
*a Ultra High Strength Steel Welding Point *b Ultra High Strength Steel Welding Point