Home › Vehicle Exterior › BODY PANEL › ROCKER PANEL
BM3160E _01 Vehicle Exterior _021870 BODY WELD POINT _0112112 ROCKER PANEL F

BODY WELD POINT  ROCKER PANEL  CUT AND JOIN REPLACEMENT SECTIONS  


K110880

REMOVAL


Symbol meaning
K108818

Remove Weld Points
K108819

Remove Weld Points
K108820

Remove Weld Points
K108826

Cut with Disc Sander etc.
K108827

Cut and Join Location
K108828

Cut Location for Supply Parts
K108829

Cut Location


REMOVAL POINT
1.

Do not butt weld or heat repair because the heat decreases the strength of areas where ultra high strength steel is used. (See the introduction)

2.

*a is reused.

3.

Reuse *b, as the area of the outer panel that is cut and joined is in front of the supplied part cut position.

4.

*c indicates the location of the foamed sealing material. Be careful when cutting as the foamed sealing material is located near the cutting position.


K110881
3.302,3.146 3.813,2.302 3.813,2.302 3.927,2.302 false 3.604,1.021 4.979,1.219 1.375,0.198 10 false 75 (2.95) 3.833,2.885 5.208,3.083 1.375,0.198 10 false 55 (2.17) 4.448,6.385 5.823,6.583 1.375,0.198 10 false 25 (0.98) 3.958,2.24 4.271,2.438 0.313,0.198 10 false *c 0.094,8.594 0.406,8.792 0.313,0.198 10 false *d 5.406,3.865 6.938,4.063 1.531,0.198 10 false 170 (6.69)
*c Foamed Sealing Material *d mm (in.)


K110882
3.656,3.646 3.458,3.646 3.458,3.646 3.667,3.073 false 4.573,1.417 6.26,1.615 1.688,0.198 10 false 330 (12.99) 3.688,3.573 4,3.771 0.313,0.198 10 false *b 0.156,8.552 0.469,8.75 0.313,0.198 10 false *e
*b Reused *e mm (in.)


K110883
0.167,8.563 0.51,8.781 0.344,0.219 10 false *f 0.604,2.719 1.979,2.917 1.375,0.198 10 false 45 (1.77) 3.302,2.781 4.677,2.979 1.375,0.198 10 false 45 (1.77)
*f mm (in.) - -


K110884
1.677,3.188 1.51,3.188 1.51,3.188 1.594,2.344 false 1.698,3.104 2.01,3.302 0.313,0.198 10 false *a
*a Reused - -


INSTALLATION


Symbol meaning
K108821

Spot Weld
K108823

Plug Weld
K108824

Plug Weld
K108825

Plug Weld
K108827

Cut and Join Location
K108830

Fillet Weld
K108831

Butt Weld
K108834

Body Sealer


Weld work for 980 MPa ultra high strength steel:

Follow the welding conditions below when welding ultra high strength steel to assure sufficient weld strength. (When repairing this model)


*a: When welding 2 panels together including 980 MPa ultra high strength steel.

Spot weld Pressure 2940 N (300 kgf, 661 lbf)
Weld current 10000 A
Weld time 16 Cyc. (0.27 Sec.)
Plug weld Plug diameter 10 mm (0.39 in.)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas


*b: When welding more than 3 panels together including 980 MPa ultra high strength steel. (When plug welding a third panel to 2 panels which are welded under the conditions described above.)

Plug weld Plug diameter Same as the standard method (See the introduction)
Wire type AWS A5.18 ER70S-3
Shield gas Metal active gas


NOTICE:

Be sure to use Metal active gas (Ar 80% + CO2 20%) as the shield gas when plug welding. Sufficient weld strength cannot be assured when using 100% CO2 shield gas.


INSTALLATION POINT
1.

Inspect the fitting of the related parts around the new parts before welding. This affects the appearance of the finish.

2.

Temporarily install the new parts and measure each part of the new parts in accordance with the body dimension diagram. (See the body dimensions)

3.

If the entire supply part is not needed, remove the part of the supply part that is needed.

4.

Before installing a new part, apply body sealer.

HINT:

Apply body sealer in an even, continuous bead.


5.

Follow the welding conditions when welding *a and *b to assure sufficient weld strength. (See the introduction)

6.

Before temporarily installing the new parts, weld the rocker panel sub-assembly outer and NO.2 inner pillar sub-assembly with the standard number of welding points.

7.

When welding *c, make a hole on a new part for plug welding and weld the panel with the panel behind completely.

8.

After welding the rocker panel sub-assembly outer and NO.2 inner pillar sub-assembly to the vehicle side, install the center body pillar sub-assembly and *d.

9.

After welding the rocker panel sub-assembly outer, NO.2 inner pillar sub-assembly, center body pillar sub-assembly and *d to the vehicle side, install the rear body front outside panel and *e.

10.

After welding, apply the foamed sealing material to the corresponding parts. (See the painting / coating)

11.

After welding, apply body sealer and undercoating to the corresponding parts. (See the painting / coating)

12.

After applying the top coat, apply anti-rust agent to the internal panel portion of the closed section structural weld points.


K110885
4.01,2.448 4.333,2.156 4.333,2.156 4.458,2.156 false 1.896,5.917 2.177,5.646 2.177,5.646 2.313,5.646 false 4.396,3.198 5.771,3.396 1.375,0.198 10 false 75 (2.95) 4.479,2.073 4.792,2.271 0.313,0.198 10 false *1 2.333,5.573 2.646,5.771 0.313,0.198 10 false *2 2.375,7.292 3.75,7.49 1.375,0.198 10 false 70 (2.76) 4.125,7.292 5.5,7.49 1.375,0.198 10 false 45 (1.77) 6.333,7.302 6.948,7.542 0.615,0.24 10 false 45 (1.77) 0.125,8.563 0.438,8.76 0.313,0.198 10 false *f
*1 CENTER BODY PILLAR SUB-ASSEMBLY *2 NO.2 INNER PILLAR SUB-ASSEMBLY
*f mm (in.) - -


K110886
3.021,1.75 2.927,1.25 2.927,1.25 2.771,1.25 false 5.25,2.563 6.781,2.76 1.531,0.198 10 false 170 (6.69) 2.615,1.177 2.927,1.375 0.313,0.198 10 false *3 0.156,8.542 0.469,8.74 0.313,0.198 10 false *g
*3 ROCKER PANEL SUB-ASSEMBLY OUTER - -
*a Ultra High Strength Steel Welding Point *g mm (in.)


K110887
1.208,7.99 2.583,8.188 1.375,0.198 10 false 15 (0.59) 2.281,8 3.656,8.198 1.375,0.198 10 false 15 (0.59) 5.156,7.906 6.531,8.104 1.375,0.198 10 false 15 (0.59) 0.094,8.615 0.406,8.813 0.313,0.198 10 false *h
*a Ultra High Strength Steel Welding Point *h mm (in.)


K110888
1.698,6.542 1.563,6.542 1.563,6.542 1.573,5.719 false 0.167,8.552 0.479,8.75 0.313,0.198 10 false *i 1.719,6.469 2.031,6.667 0.313,0.198 10 false *d 3.938,8.604 5.313,8.802 1.375,0.198 10 false 22 (0.87) 4.896,2.125 6.271,2.323 1.375,0.198 10 false 15 (0.59)
*i mm (in.) - -


K110889

K110890
3.49,3.771 3.365,3.771 3.365,3.771 3.542,2.958 false 1.323,7.833 1.167,7.833 1.167,7.833 1.479,7.24 false 3.51,3.677 3.833,3.875 0.323,0.198 10 false *4 1.365,7.75 1.677,7.948 0.313,0.198 10 false *e
*4 REAR BODY FRONT OUTSIDE PANEL - -
*b Ultra High Strength Steel Welding Point - -


K110907