Home › Vehicle Exterior › BODY DIMENSIONS › MEASURING INFORMATION
BM3160E _01 Vehicle Exterior _021871 BODY DIMENSIONS _0112129 MEASURING INFORMATION F

BODY DIMENSIONS  MEASURING INFORMATION  DIAGRAM DESCRIPTION  


HINT:
·

There are two types of dimensions in the diagram.

·

In cases in which only one dimension is given, left and right are symmetrical.

·

For symbols, capital letters indicate right side of vehicle, small letters indicate left side of vehicle (seen from rear).



Three-Dimensional Distance


K104022
1.438,0.031 1.667,0.188 0.229,0.156 10 true *a
*a Distance between the centers of the measuring points


a.

Straight-line distance between the centers of two measuring points.



Two-Dimensional Distance


K110301
1.958,1.031 2.271,1.188 0.313,0.156 10 false *a 1.583,2.698 1.896,2.854 0.313,0.156 10 false *b 2.49,2.427 2.802,2.583 0.313,0.156 10 false *c 1.083,3.208 1.396,3.365 0.313,0.156 10 false *d
*a Center-to-center horizontal distance in forward/rearward
*b Vertical distance to center
*c Vertical distance to lower surface
*d Imaginary Datum Line


a.

Horizontal distance in forward/rearward between the centers of two measuring points.


b.

Distance from the Imaginary Datum Line.



Imaginary Datum Line


K104023
1.354,0.771 1.667,0.927 0.313,0.156 10 false *a 1.198,1.885 1.51,2.042 0.313,0.156 10 false *b 0.26,1.552 0.719,1.75 0.458,0.198 10 false (1) 1.438,1.542 1.896,1.74 0.458,0.198 10 false (2) 2.677,1.542 3.135,1.74 0.458,0.198 10 false (3) 0.438,1.833 0.896,2.031 0.458,0.198 10 false A 1.646,1.833 2.104,2.031 0.458,0.198 10 false B 2.844,1.833 3.302,2.031 0.458,0.198 10 false C
*a Under surface of the Rocker Panel
*b Imaginary Datum Line


a.

The imaginary line used to measure height is a line which connects the points described in the following chart (actual dimensions are listed in the next chapter of this manual).

Symbol Measuring Points
A The place that was lowered (1) mm from the under surface of the rocker panel centered on the front jack up point.
B The place that was lowered (2) mm from the under surface of the rocker panel centered between A and C.
C The place that was lowered (3) mm from the under surface of the rocker panel centered on the rear jack up point.



Measurement


K104025
0.906,2.667 1.219,2.823 0.313,0.156 10 false *a 2.625,2.677 2.938,2.833 0.313,0.156 10 false *b 0.948,0.667 1.26,0.823 0.313,0.156 10 false *1 2.052,2.208 2.365,2.365 0.313,0.156 10 false *2 0.719,1.781 1.031,1.938 0.313,0.156 10 false *3 1.833,3.469 2.146,3.625 0.313,0.156 10 false *3
*1 Tracking Gauge
*2 Master Gauge
*3 Pointer
*a Wrong
*b Correct


a.

Basically, all measurements are to be done with a tracking gauge. For portions where it is not possible to use a tracking gauge, a tape measure should be used.


b.

Use only a tracking gauge that has no looseness in the body, measuring plate, or pointers.


c.

When using a tape measure, avoid twists and bends in the tape.

HINT:
·

The height of the left and right pointers must be equal.

·

Always calibrate the tracking gauge before measuring or after adjusting the pointer height.

·

Take care not to drop the tracking gauge or otherwise shock it.

·

Confirm that the pointers are securely in the holes.