Home › General › INTRODUCTION › WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS › from 2016.11
BM3160E _V1 General _021869 INTRODUCTION _0112095 WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS F

INTRODUCTION  WHEN REMOVING,INSTALLING,REPAIRING OR REPLACING PARTS  PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED  


Refer to the TOYOTA Repair Manual for each work procedure.

PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED


Replacement Part Necessary Procedure Effect/Inoperative Function when Necessary Procedures are not Performed Note
ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on for 1AR-FE
for 2GR-FKS
ECU communication ID registration (Immobiliser system) Engine start function See the Service Bulletin for the registration method.
·

Throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Engine assembly

·

Cylinder head sub-assembly

·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly

·

Fuel pump

·

Air fuel ratio sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock control sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


for 1AR-FE
·

Throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Engine assembly

·

Cylinder head sub-assembly

·

Camshaft (for intake or exhaust camshaft)

·

Camshaft timing gear assembly

·

Camshaft timing exhaust gear assembly

·

Piston or piston ring

·

Mass air flow meter sub-assembly

·

Fuel injector assembly (for port injection)

·

Fuel injector assembly (for direct injection)

·

Fuel pump (for low pressure side)

·

Fuel pump assembly (for high pressure side)

·

Fuel pressure sensor (for low pressure side)

·

Fuel pressure sensor (for high pressure side)

·

Air fuel ratio sensor

·

Engine coolant temperature sensor

·

Spark plug

·

Ignition coil assembly

·

Air leaks from intake system

·

Gas leaks from exhaust system

·

Knock control sensor


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


for 2GR-FKS
Millimeter wave radar sensor assembly Adjust millimeter wave radar sensor assembly
·

Dynamic radar cruise control system

·

Forward recognition camera system

·

Lane departure alert system (w/ Steering Control)

·

Road sign assist system

·

Pre-collision system


-
·

Forward recognition camera

·

Windshield glass


Adjust forward recognition camera
·

Dynamic radar cruise control system

·

Forward recognition camera system

·

Lane departure alert system (w/ Steering Control)

·

Road sign assist system

·

Pre-collision system

·

Automatic high beam system


-
Automatic transaxle assembly
1.

Reset memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to Learn


·

Large shift shock

·

Deterioration of fuel efficiency


for UA80E Initialization
for UA80E Registration
for UA80F Initialization
for UA80F Registration
·

Valve body assembly

·

Shift solenoid valve SL1, SL2, SL3, SL4, SL5 and/or SL6


1.

Reset memory

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


ECM (If possible, read the transaxle compensation code from the previous ECM) Possible
1.

Reset memory*13

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Impossible
1.

Reset memory*13

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Automatic transaxle assembly
1.

Reset memory

2.

Input transaxle compensation code into ECM

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for U760E Initialization
for U760E Registration
·

Valve body assembly

·

Shift solenoid valve SL3 and/or SL4


1.

Reset memory

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Shift solenoid valve SL1 and/or SL2 Perform road test to allow ECM to learn
ECM
(If possible, read the transaxle compensation code from the previous ECM)
Possible
1.

Reset memory

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


Impossible
1.

Reset memory

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


·

4WD ECU assembly*1

·

Acceleration sensor (airbag sensor assembly)


Perform calibration AWD initial performance (acceleration, etc) -
·

Tire pressure warning ECU

·

Tire pressure warning valve and transmitter


1.

Register transmitter IDs

2.

Initialize tire pressure warning system


·

When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.

·

Tire pressure warning function


for Initialization
for Registration
Skid control ECU (brake actuator assembly)
1.

Clear zero point calibration data and store system information.

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information.


·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


-
Yaw rate and acceleration sensor (airbag sensor assembly)
1.

Clear zero point calibration data and store system information.

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information.


Power steering ECU assembly Assist map writing
·

DTCs are output

·

EPS control

·

EPS warning light illuminated


-
Telematics transceiver*10 Register vehicle information Emergency call service -
Mobilephone battery*10 Reset mobilephone battery condition
·

Spiral cable with sensor sub-assembly

·

Steering sensor


·

Steering angle neutral point (Initialize parking assist monitor system)

·

Steering angle setting


Parking assist monitor system for Initialization
for Calibration
Suspension, tires, etc. Television camera assembly optical axis (Back camera position setting)
Television camera assembly
·

Parking assist monitor system initialization

·

Television camera assembly optical axis (Back camera position setting)


Blind spot monitor sensor Blind spot monitor beam axis inspection DTCs are output -
Steering sensor Steering angle neutral point (Initialize panoramic view monitor system) Panoramic view monitor system for Initialization
for Calibration
Parking assist ECU
·

Parking assist ECU initialization

·

Adjust steering angle


Television camera assembly Rear television camera view adjustment
·

Front television camera assembly

·

Front bumper assembly


Front television camera view adjustment
·

Side television camera assembly LH

·

Outer rear view mirror assembly LH

·

Side television camera assembly RH

·

Outer rear view mirror assembly RH


Side television camera view adjustment
·

Front television camera assembly or front bumper assembly

·

Television camera assembly

·

Side television camera assembly LH or outer rear view mirror assembly LH

·

Side television camera assembly RH or outer rear view mirror assembly RH


Television camera view adjustment
Suspension, tires, etc.*11
·

Parking assist ECU initialization

·

Adjust steering angle


·

Certification ECU (smart key ECU assembly)*2

·

ID code box (immobiliser code ECU)*2*4

·

Steering lock ECU (steering lock actuator assembly)*2

·

Electrical key transmitter sub-assembly*2

·

ECM*2

·

Main body ECU (multiplex network body ECU)*2


Code registration (Immobiliser system (w/ Smart Entry and Start System))
·

Wireless door lock control system

·

Smart entry and start system

·

Engine start

·

Steering lock system


See Service Bulletin for the registration method.
·

Transponder key ECU assembly*3

·

Door control receiver

·

ECM*3


Code registration (Immobiliser system (w/o Smart Entry and Start System))
·

Wireless door lock control system

·

Engine start


See Service Bulletin for the registration method.
·

Door control transmitter module set sub-assembly

·

Door control receiver


Code registration (Wireless door lock system (w/o Smart Entry and Start System)) Wireless door lock control system *3
·

No. 1 air conditioning radiator damper servo sub-assembly

·

No. 2 air conditioning radiator damper servo sub-assembly

·

Rear air mix damper servo sub-assembly

·

Rear mode damper servo sub-assembly

·

Blower damper servo sub-assembly


Initialization servo motor (Air conditioning system (for Automatic Air Conditioning System)) DTCs are output *5
·

No. 1 air conditioning radiator damper servo sub-assembly

·

Rear air mix damper servo sub-assembly

·

Rear mode damper servo sub-assembly

·

Blower damper servo sub-assembly


Initialization servo motor (Air conditioning system (for Manual Air Conditioning System)) DTCs are output *6
·

Door window regulator assembly

·

Power window regulator motor assembly

·

Door glass

·

Door glass run


Initialize power window control system (for Models with Jam Protection Function on 4 Windows)
·

Auto up and down function

·

Jam protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function


*7
·

Door window regulator assembly

·

Power window regulator motor assembly (for driver door)

·

Power window regulator motor assembly (for front passenger door)

·

Door glass

·

Door glass run


Initialize power window control system (for Models with Jam Protection Function on Front Door Windows)
·

Auto up and down function

·

Jam protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function


*8
·

Sliding roof ECU (sliding roof drive gear sub-assembly)

·

Sliding roof glass sub-assembly

·

Sliding roof drive cable sub-assembly


Initialize sliding roof system
·

Auto operation function

·

Jam protection function

·

Key-off operation function

·

Key-linked function

·

Wireless transmitter-linked function

·

Sliding roof open warning function


-
·

Multiplex network door ECU*9

·

Power back door unit assembly set LH or RH*9

·

Back door lock assembly*9


Reset back door close position Power back door system -
Headlight leveling ECU assembly*12
·

Synchronize the vehicle information

·

Perform headlight leveling ECU assembly initialization


Headlight leveling function -
Rear height control sensor sub-assembly*12 Perform headlight leveling ECU assembly initialization Headlight leveling function


*1: When the 4WD ECU assembly is replaced with a new one, calibration is unnecessary.

*2: w/ Smart entry and start system

*3: w/o Smart entry and start system

*4: w/ Rear Seat Heater

*5: for Automatic Air Conditioning System

*6: for Manual Air Conditioning System

*7: w/ Jam Protection Function on 4 Windows

*8: w/ Jam Protection Function on Front Door Windows

*9: w/ Power Back Door System

*10: w/ Manual (SOS) Switch

*11: The vehicle height changes because of suspension or tire replacement

*12: w/ Automatic Headlight Beam Level Control System

*13: When the ECM is replaced with a new one, reset memory is unnecessary.