Home › Engine / Hybrid System › 1AR-FE ENGINE CONTROL › SFI SYSTEM
NM3160E _51 Engine / Hybrid System _020724 1AR-FE ENGINE CONTROL _0105512 SFI SYSTEM DE DETAILS F

1AR-FE ENGINE CONTROL  SFI SYSTEM  DETAILS  ACCELERATOR PEDAL SENSOR  


CONSTRUCTION


a.

This non-contact type accelerator pedal sensor assembly uses a Hall IC, which is mounted on the accelerator pedal arm.

i.

A magnetic yoke is mounted at the base of the accelerator pedal arm. This yoke rotates around the Hall IC in accordance with the amount of effort that is applied to the accelerator pedal. The Hall IC converts the changes in magnetic flux that occur into electrical signals, and outputs them in the form of accelerator pedal position signals to the ECM.


ii.

The Hall IC contains 2 circuits, one for the main signal, and one for the sub signal. It converts the accelerator pedal position (angle) into electric signals that have differing characteristics and outputs them to the ECM.

W111437
3.323,0.333 3.656,0.333 3.656,0.333 4.625,1.063 true 4.813,1.156 5.833,1.156 true 4.094,3.01 4.344,3.01 4.344,3.01 4.594,3.625 true 4.125,5.406 4.375,5.406 4.375,5.406 4.563,4.938 true 2.344,0.25 3.323,0.479 0.979,0.229 10 false Magnetic Yoke 5.885,1.073 6.354,1.271 0.469,0.198 10 false Hall IC 3.594,2.927 4.125,3.198 0.531,0.271 10 false Magnet 4.427,4.104 4.688,4.479 0.26,0.375 10 false Hall IC 3.625,5.323 4.156,5.594 0.531,0.271 10 false Magnet 3.292,5.729 5.552,5.979 2.26,0.25 10 false Accelerator Pedal Sensor Assembly 5.344,3.469 5.729,3.698 0.385,0.229 10 false VPA 5.344,3.823 5.729,4.052 0.385,0.229 10 false EPA 5.365,4.156 5.813,4.396 0.448,0.24 10 false VCPA 5.365,4.438 5.792,4.688 0.427,0.25 10 false VPA2 5.354,4.813 5.781,5.052 0.427,0.24 10 false EPA2 5.365,5.177 5.792,5.417 0.427,0.24 10 false VCP2 6.271,4.229 6.646,4.458 0.375,0.229 10 false ECM 3.698,7.458 4.083,7.688 0.385,0.229 10 false VPA 2.729,6.948 3.156,7.198 0.427,0.25 10 false VPA2 1.396,6.104 1.635,6.344 0.24,0.24 10 false (V) 1.448,6.333 1.573,6.563 0.125,0.229 10 false 5 1.448,8.031 1.573,8.26 0.125,0.229 10 false 0 0.531,7.177 1.51,7.427 0.979,0.25 10 false Output Voltage 0.76,8.323 1.625,8.552 0.865,0.229 10 false Fully Closed 2.302,8.177 4.438,8.448 2.135,0.271 10 false Accelerator Pedal Position (Angle) 5.198,8.302 5.917,8.573 0.719,0.271 10 false Fully Open

HINT:

The inspection method for this accelerator pedal sensor assembly differs from a contact type accelerator pedal sensor assembly because a non-contact type accelerator pedal sensor assembly uses a Hall IC. For details, refer to the Repair Manual.