Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › 2013.12–2016.11
NM3160E _51 Engine / Hybrid System _020739 2GR-FE ENGINE CONTROL _0105513 SFI SYSTEM DE DETAILS F

2GR-FE ENGINE CONTROL  SFI SYSTEM  DETAILS  CAMSHAFT POSITION SENSOR  


CONSTRUCTION


a.

Magneto-Resistance Element (MRE) type camshaft position sensors (intake and exhaust) are used. To detect the position of each intake camshaft, a timing rotor that is secured to the intake camshaft in front of the camshaft timing gear assembly is used to generate 6 (3 high output, 3 low output) pulses for every 2 revolutions of the crankshaft. The timing rotor for each exhaust camshaft is part of the respective camshaft.

W100688
4.302,0.26 4.688,0.26 4.688,0.26 5.135,0.604 true 1.104,2.521 1.5,2.521 1.5,2.521 1.927,1.917 true 2.906,2.5 2.583,2.5 2.583,2.5 2.427,2.115 true 5.646,2.594 5.219,2.594 5.219,2.594 4.99,1.865 true 0.271,2.438 1.167,2.781 0.896,0.344 10 false Timing Rotor 5.698,2.521 6.594,2.813 0.896,0.292 10 false Timing Rotor 2.948,2.448 4.583,2.938 1.635,0.49 10 false Camshaft Position Sensor (Bank 1 Intake Side) 1.271,0.188 4.292,0.49 3.021,0.302 10 false Camshaft Position Sensor (Bank 1 Exhaust Side) 0.167,3.01 2.25,3.365 2.083,0.354 12 false Sensor Output Waveforms: 2.688,3.177 5.813,3.458 3.125,0.281 10 false Camshaft Position Sensor Signal Plate (720° CA) 0.188,3.833 1.354,4.417 1.167,0.583 10 false Camshaft Position Sensor Signal 0.302,5.375 1.25,5.948 0.948,0.573 10 false Crank Position Sensor Signal 1.271,4.833 1.563,5.021 0.292,0.188 10 false 0 V 1.271,5.802 1.563,5.99 0.292,0.188 10 false 0 V 2.135,6.573 2.667,6.771 0.531,0.198 10 false 10° CA 3,5.042 3.594,5.198 0.594,0.156 10 false 360° CA 2.375,4.427 2.969,4.583 0.594,0.156 10 false 180° CA 4.979,4.438 5.573,4.594 0.594,0.156 10 false 120° CA 5.677,3.75 6.271,3.906 0.594,0.156 10 false 120° CA 3.083,3.76 3.604,3.917 0.521,0.156 10 false 60° CA 3.438,4.646 3.958,4.802 0.521,0.156 10 false 60° CA 4.125,3.75 4.719,3.906 0.594,0.156 10 false 180° CA 5.083,5.042 5.719,5.198 0.635,0.156 10 false 360° CA


b.

An MRE type camshaft position sensor consists of an MRE, a magnet and a sensor. The direction of the magnetic field changes due to the profile (protruding and non-protruding portions) of the timing rotor, which passes by the sensor. As a result, the resistance of the MRE changes, and the output voltage to the ECM changes to high or low. The ECM detects the camshaft position based on this output voltage.

W100681
4.729,3.969 5.219,3.198 5.219,3.198 5.448,3.198 true 4.469,4.75 4.469,5.229 true 1.885,5.542 2.573,5.698 0.688,0.156 10 MRE Type 4.938,5.542 5.813,5.708 0.875,0.167 10 Pick-up Type 0.521,3.094 1.042,3.49 0.521,0.396 10 Engine Speed 3.542,3.094 4.021,3.51 0.479,0.417 10 Engine Speed 0.521,4.781 1.021,5.146 0.5,0.365 10 Sensor Output 3.542,4.49 4.042,4.854 0.5,0.365 10 Sensor Output 2.219,5.219 3.167,5.438 0.948,0.219 10 Digital Output 6.104,4.781 7.083,5 0.979,0.219 10 Analog Output 3.948,5.24 5.302,5.427 1.354,0.188 10 Non Detection Area 5.531,3.104 7,3.292 1.469,0.188 10 Non Detection Area 4.75,1 5.188,1.229 0.438,0.229 10 ECM 1.635,1.354 3.26,1.875 1.625,0.521 10 Camshaft Position Sensor (Bank 1 Intake Side) 0.76,1.625 1.615,1.823 0.854,0.198 10 Timing Rotor 0.135,0.042 1.385,0.24 1.25,0.198 12 Wiring Diagram: 0.188,2.229 5.563,2.688 5.375,0.458 12 MRE Type and Pick-up Coil Type Output Waveform Image Comparison: 3.865,0.625 4.115,0.823 0.25,0.198 10 VC 3.708,0.948 4.083,1.146 0.375,0.198 10 VV1+ 3.729,1.271 4.104,1.469 0.375,0.198 10 VV1-