Home › Engine / Hybrid System › 1AR-FE ENGINE MECHANICAL › ENGINE UNIT
NM3160E _51 Engine / Hybrid System _020725 1AR-FE ENGINE MECHANICAL _0105514 ENGINE UNIT DE DETAILS F

1AR-FE ENGINE MECHANICAL  ENGINE UNIT  DETAILS  BALANCE SHAFT  


CONSTRUCTION


a.

Balance shafts are used to reduce vibration.


b.

The crankshaft directly drives the No. 1 balance shaft.


c.

In addition, a resin gear is used on the driven side to suppress noise and offer a lightweight design.

W100801
2.917,0.969 2.917,0.281 2.917,0.281 3.156,0.281 true 5.354,1.01 5.99,1.01 true 4.396,3.083 5.146,3.083 true 4.167,4.156 5.156,4.156 true 3.677,4.542 4.875,4.542 true 4.427,5.51 5.167,5.51 true 2.469,3.396 1.563,3.396 true 2.292,3.75 1.563,3.75 true 3.208,0.188 3.417,0.396 0.208,0.208 10 false *1 6.021,0.927 6.229,1.135 0.208,0.208 10 false *2 5.177,3.01 5.385,3.219 0.208,0.208 10 false *3 1.396,3.677 1.604,3.885 0.208,0.208 10 false *4 5.188,4.073 5.396,4.281 0.208,0.208 10 false *5 1.396,3.323 1.604,3.531 0.208,0.208 10 false *6 4.917,4.49 5.125,4.698 0.208,0.208 10 false *6 5.177,5.406 5.385,5.615 0.208,0.208 10 false *7
*1 Balance Shaft Drive Gear *2 Crankshaft
*3 No. 2 Balance Shaft Housing *4 No. 2 Balance Shaft
*5 No. 1 Balance Shaft *6 Resin Gear
*7 No. 1 Balance Shaft Housing - -



d.

In an in-line 4-cylinder engine, the crankshaft angle for cylinders No. 1 and No. 4 is exactly the opposite (180°) from the position of cylinders No. 2 and No. 3. Therefore, the inertial force of the pistons and the connecting rods of the former 2 cylinders and of the latter 2 cylinders almost cancels each other out. However, because the position at which the piston reaches its maximum speed is located toward top dead center from the center of the stroke, the upward inertial force is greater than the downward inertial force. This unbalanced secondary inertial force is generated twice for each rotation of the crankshaft.

Inertial Force Generated by In-line 4 Cylinders
W107385
1.625,0.49 2.344,0.49 true 1.615,0.927 2.354,0.927 true 1.583,1.667 2.333,1.667 true 4,1.292 3.5,1.292 true 3.958,1.76 3.458,1.76 true 4,2.083 3.5,2.083 true 3.5,2.333 4.083,2.333 true 2.385,0.396 2.573,0.604 0.188,0.208 10 false *l 2.385,0.833 2.573,1.042 0.188,0.208 10 false *m 2.229,1.979 2.417,2.188 0.188,0.208 10 false *m 0.76,1.927 1,2.146 0.24,0.219 10 false *m 2.396,1.563 2.583,1.771 0.188,0.208 10 false *n 3.333,1.208 3.542,1.417 0.208,0.208 10 false *a 3.302,1.677 3.49,1.885 0.188,0.208 10 false *b 3.323,2.24 3.51,2.448 0.188,0.208 10 false *e 3.313,2 3.5,2.208 0.188,0.208 10 false *c 4.521,0.615 4.708,0.823 0.188,0.208 10 false *d 3.76,2.958 4.021,3.167 0.26,0.208 10 false *f 4.26,2.958 4.521,3.167 0.26,0.208 10 false *g 4.729,2.958 4.99,3.167 0.26,0.208 10 false *h 5.198,2.958 5.458,3.167 0.26,0.208 10 false *i 5.708,2.958 5.969,3.167 0.26,0.208 10 false *j 6.25,2.958 6.51,3.167 0.26,0.208 10 false *k
*a Inertial Force of Cylinders No. 2 and No. 3 *b Combined Inertial Force of All Cylinders
(Unbalanced Secondary Inertial Force)
*c Inertial Force of Engine Balancer Assembly *d Force
*e Inertial Force of Cylinders No. 1 and No. 4 *f -180°
*g -90° *h 0°
*i 90° *j 180°
*k 270° *l Top Dead Center
*m Point of Max. Speed *n Bottom Dead Center



e.

To cancel the unbalanced secondary inertial force, 2 balance shafts are provided that rotate twice for each rotation of the crankshaft. By doing this they generate an inertial force in the opposite direction. Also, in order to cancel the inertial force generated by the balance shafts themselves, there are actually 2 shafts rotating in opposite directions.

Inertial Force of Balance Shafts
W100813
6.125,0.688 6.625,0.688 false 6.052,1.802 6.656,1.802 false 4.198,3.01 4.198,2.396 4.198,2.396 4.792,2.396 true 4.063,3.188 4.802,3.188 true 0.583,1.323 0.771,1.479 0.188,0.156 10 false *a 2.281,1.323 2.49,1.5 0.208,0.177 10 false *b 3.969,1.323 4.177,1.51 0.208,0.188 10 false *c 5.677,1.323 5.885,1.51 0.208,0.188 10 false *d 6.677,0.594 6.854,0.76 0.177,0.167 10 false *f 6.677,1.146 6.865,1.375 0.188,0.229 10 false *g 6.698,1.719 6.875,1.917 0.177,0.198 10 false *h 4.833,2.323 5.031,2.469 0.198,0.146 10 false *e 4.833,3.094 5.063,3.271 0.229,0.177 10 false *f
*a 0° *b 90°
*c 180° *d 270°
*e Direction of Mass of Balance Shaft *f Inertial Force of Balance Shafts
*g Crankshaft Angle *h Secondary Inertial Force