Home › Engine / Hybrid System › CRUISE CONTROL › LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) › from 2016.11
NM3160E _51 Engine / Hybrid System _020754 CRUISE CONTROL _0298035 LANE DEPARTURE ALERT SYSTEM(w/ Steering Control) CO CONTROL F

CRUISE CONTROL  LANE DEPARTURE ALERT SYSTEM(w/ Steering Control)  CONTROL  LANE DEPARTURE ALERT CONTROL  


FUNCTION OF MAIN COMPONENTS


Components Function
Combination Meter Assembly Transmits a turn signal command to the forward recognition camera.
Combination Meter Assembly Lane Departure Alert Indicator (LDA Indicator) Illuminates or turns off in accordance with signals from the forward recognition camera.
Multi-information Display Displays a warning message and white lines to inform or warn the driver of the system condition in accordance with signals from the forward recognition camera.
Master Warning Light Illuminates to warn the driver in accordance with signals from the forward recognition camera.
Buzzer Sounds to warn the driver in accordance with signals from the forward recognition camera.
Forward Recognition Camera
·

Captures a view of the road ahead of the vehicle and detects lane markers on the driving lane, and calculates the radius to the center of the lane, lane width, distance from markers and heading angle deviation.

·

Controls the LDA system.

·

Transmits the indicator illumination request signal, multi-information display indication request signal, and buzzer sound request signal to the combination meter assembly.

·

Receives vehicle information and turn signal light operation signals and sends a steering force signal to the power steering ECU assembly.


Millimeter Wave Radar Sensor Assembly Radiates millimeter waves forward, uses the reflected waves to detect the presence of a vehicle traveling ahead and then transmits this information to the forward recognition camera.
Driving Support ECU Assembly Transmits the LDA main switch signal to the forward recognition camera.
ECM Sends the reverse signal to the forward recognition camera.
Headlight Dimmer Switch Assembly Transmits a turn signal command to the combination meter assembly.
Brake Actuator Assembly Skid Control ECU Sends a vehicle speed signal from the speed sensor to the forward recognition camera.
Steering Pad Switch Assembly Lane Departure Alert Main Switch (LDA Main Switch) Detects an on/off status of the system and transmits a signal to the forward recognition camera.
Airbag Sensor Assembly Yawrate Sensor Detects yaw rate and transmits a signal to the forward recognition camera.
Steering Sensor Detects the angle and direction of steering and transmits signals to the forward recognition camera.
Power Steering ECU Assembly
·

Controls the power steering motor assembly according to signals from the forward recognition camera.

·

Sends steering torque signals from the torque sensor to the power steering ECU assembly.

·

Detects steering operations performed by the driver and outputs the operations to the forward recognition camera.

·

Cancels steering assist when an abnormal torque request signal is received from the forward recognition camera.


Main Body ECU (Multiplex Network Body ECU) Sends country specification information signals to the forward recognition camera.
Speed Sensors Detects the vehicle speed and transmits a signal via the skid control ECU to the forward recognition camera.
Central Gateway ECU (Network Gateway ECU) Gateway function of CAN communication.


OPERATION CONDITION


a.

Operating Conditions of LDA System (Lane Departure Alert Function)

Operation Condition
Operating The LDA system (lane departure alert function) is activated when all of the following conditions are met:
·

The LDA main switch is on. (When the LDA main switch is pressed to turn on the LDA system, the LDA indicator illuminates).

·

The vehicle speed is between approximately 50 and 270 km/h (32 and 168 mph).

·

Lane markers are detected.

·

LDA system becomes activated when the turning signal is set to the opposite direction against the heading direction.

·

System malfunction is not detected.


Suspended The LDA system (lane departure alert function) is suspended when any one of the following conditions is met:
·

The vehicle speed is not between approximately 50 and 270 km/h (32 and 168 mph).

·

A turn signal command is detected.

·

No lane markers are detected.

·

Immediately after the LDA is activated.

·

A malfunction is detected in the LDA system.

·

The temperature of the forward recognition camera is abnormal.

·

The vehicle crosses halfway or further over a lane marker.


Canceled/Resume The LDA system (lane departure alert function) is stopped when any one of the following conditions is met:
·

The LDA main switch is off.

·

The LDA system is malfunctioning.

·

The engine switch is turned off.


The LDA system (lane departure alert function) resumes when the following conditions are met:
·

The conditions to start operation listed above returns to are satisfied.

·

The LDA system condition returns to normal.

·

The engine switch is turned off and on (IG) again to ensure normal operation, after the LDA system has been stopped by a system malfunction.




b.

Operating Conditions of LDA System (Steering Assist Function)

Operation Condition
Operating The LDA system (steering assist function) is activated when all of the following conditions are met:
·

The LDA main switch is on. (When the LDA main switch is pressed to turn on the LDA system, the LDA indicator illuminates).

·

The vehicle speed is between approximately 50 and 200 km/h (32 and 124 mph).

·

Lane markers are detected.

·

No turn signal command is detected.

·

System malfunction is not detected.

·

The steering assist available is selected via operation on the steering pad switch assembly.

·

Deceleration at or above a constant speed is not detected.

·

Steering operations to change the direction of vehicle travel are not performed.

·

Systems related to vehicle safety, such as the VSC and pre-collision system, do not operate.

·

Acceleration via operation of the accelerator pedal is not detected.


Suspended The LDA system (steering assist function) is suspended when any one of the following conditions is met:
·

The vehicle speed is not between approximately 50 and 200 km/h (32 and 124 mph).

·

A turn signal command is detected.

·

No lane markers are detected.

·

Immediately after the lane departure warning is activated.

·

The airbag sensor (yawrate sensor) assembly is malfunctioning.

·

A malfunction is detected in the LDA system.

·

The deceleration sensor or steering sensor is malfunctioning.

·

The vehicle crosses halfway or further over a lane marker.

·

Steering assist generated to change the direction of vehicle travel is detected.

·

Deceleration at or above a constant speed is detected.

·

Systems related to vehicle safety, such as the VSC and pre-collision system, operate.

·

Acceleration via operation of the accelerator pedal is detected.

·

The temperature of the forward recognition camera is abnormal.

·

No steering wheel operation detected.


Canceled/Resume The LDA system (steering assist function) is stopped when any one of the following conditions is met:
·

The LDA main switch is off.

·

The LDA system is malfunctioning.

·

The engine switch is turned off.

·

Steering assist unavailable is selected via operation of the steering pad switch assembly.


The LDA system (steering assist function) resumes when the following conditions are met:
·

The conditions to start operation listed above returns to are satisfied.

·

The LDA system condition returns to normal.

·

The engine switch is turned off and on (IG) again to ensure normal operation, after the LDA system has been stopped by a system malfunction.

·

The steering assist available is selected via operation on the meter control switch.




c.

Operating Conditions of LDA System (Vehicle Sway Warning Function)

Operation Condition
Operating The LDA system (vehicle sway warning function) is activated when all of the following conditions are met:
·

The vehicle speed is between approximately 50 and 200 km/h (32 and 124 mph).

·

Lane markers are detected.

·

System malfunction is not detected.

·

The vehicle sway warning ON is selected via operation of the steering pad switch assembly.


Suspended The LDA system (vehicle sway warning function) is suspended when any one of the following conditions is met:
·

The vehicle speed is not between approximately 50 and 200 km/h (32 and 124 mph).

·

A turn signal command is detected.

·

No lane markers are detected.

·

Immediately after the lane departure warning is activated.


Canceled/Resume The LDA system (vehicle sway warning function) is stopped when any one of the following conditions is met:
·

The LDA system is malfunctioning.

·

The engine switch is turned off.

·

The vehicle sway warning OFF is selected via operation of the steering pad switch assembly.


The LDA system (vehicle sway warning function) resumes when the following conditions are met:
·

The conditions to start operation listed above are satisfied.

·

The LDA system condition returns to normal.

·

The engine switch is turned off and on (IG) again to ensure normal operation, after the LDA system has been stopped by a system malfunction.

·

The vehicle sway warning ON is selected via operation of the steering pad switch assembly.





SYSTEM CONTROL


a.

LDA System Warning Operation

i.

Function Overview (Lane Departure Alert Function)

·

If the system judges that the vehicle may deviate from the lane it is in, the system illuminates the indicator in the combination meter display and sounds a buzzer so that the driver can take action to avoid lane departure.

Y187255E06
2.823,0.948 3.396,1.198 0.573,0.25 10 false Warning



ii.

Function Overview (Steering Assist Function)

·

If the system judges that the vehicle may deviate from the lane it is in, the system performs steering assist to help the driver correct the path of the vehicle. If the driver does not take appropriate action, the system sound a buzzer.

Y180901E05
0.115,1.813 1.49,2.094 1.375,0.281 10 false Control output level 2.146,2.094 4.156,2.521 2.01,0.427 10 false Example of vehicle behavior and control output 5.948,0.979 6.552,1.375 0.604,0.396 10 false Steering Assist



iii.

Function Overview (Vehicle Sway Warning Function)

·

The system detects drift of the vehicle within its lane, which is often the result of a driver who is tired, distracted or not looking ahead, based on the position of the vehicle within its lane and the steering inputs of the driver and alert the driver before a lane departure or collision occurs.

Y180903E03
6.104,0.698 7.031,1 0.927,0.302 10 false Warning 4.292,2.063 6.094,2.313 1.802,0.25 10 false Buzzer and Warning Display





FUNCTION


a.

Using the Meter Control Switches of the steering pad switch assembly, the steering assist functions and the vehicle sway warning functions can be customized.

Y205900C01
4.688,1.802 5.219,1.135 5.219,1.135 5.396,1.135 true 4.438,2.271 5.125,2.833 5.125,2.833 5.302,2.833 true 5.427,1.042 5.74,1.198 0.313,0.156 10 false *a 5.333,2.74 5.646,2.896 0.313,0.156 10 false *b 0.146,3.51 0.458,3.667 0.313,0.156 10 false *c
*a Meter Control Switch *b Lane departure Alert Main Switch (LDA Main Switch)
*c This illustration is an example. - -



b.

Customize LDA system settings Functions

Item (Select using the up/down button of the meter control switch) Description Setting (Change using the center button of the meter control switch)
Steering Assist Select to turn steering wheel assistance on/off
·

ON

·

OFF


Warning Sensitivity Timing of lane departure alert
·

Normal

·

High




c.

Customize Vehicle Sway Warning Functions

Item (Select using the up/down button of the meter control switch) Description Setting (Change using the center button of the meter control switch)
Vehicle Sway Warning Select to turn the sway warning function on/off
·

ON

·

OFF


Vehicle Sway Detection Sensitivity Timing of sway warning
·

High

·

Standard

·

Low




d.

The vehicle sway warning function provides a warning to alert the driver when any of the following conditions occur:

Y189676E11
4.823,3.156 5.917,3.51 1.094,0.354 10 false Would you like to Take a Rest? 4.76,1.49 6.063,1.76 1.302,0.271 10 false Please Take a Rest 0.948,3.677 4.281,4.063 3.333,0.385 10 false Sudden steerage after the steerage number of times of the driver decreasing when concentration fell. 1.198,2.406 4.208,2.635 3.01,0.229 10 false Slow meandering driving when concentration fell. 1.427,1.458 3.635,1.719 2.208,0.26 10 false The continuous lane traffic deviation. 1.854,0.448 3.396,0.719 1.542,0.271 10 false Timing of lane departure 4.844,0.458 6.094,0.74 1.25,0.281 10 false Warning Display 0.198,5.417 2.542,5.625 2.344,0.208 10 false This illustration is an example.



DIAGNOSIS


a.

If a malfunction is detected in the LDA system, the forward recognition camera cancels the LDA system, illuminates the LDA indicator in yellow, illuminates the master warning light, sounds the buzzer in the combination meter assembly and displays a message on the multi-information display to inform the driver of the malfunction.


b.

At the same time, the malfunction is stored in memory as a Diagnostic Trouble Code (DTC). When a Global TechStream (GTS) is connected to the DLC3, the DTC can be read. For details, refer to the Repair Manual.