Home › Engine / Hybrid System › 2GR-FKS ENGINE MECHANICAL › ENGINE UNIT › from 2016.11
NM3160E _51 Engine / Hybrid System _060957 2GR-FKS ENGINE MECHANICAL _0298832 ENGINE UNIT GE GENERAL F

2GR-FKS ENGINE MECHANICAL  ENGINE UNIT  GENERAL  GENERAL  


OUTLINE


a.

The 2GR-FKS engine is a 3.5-liter, 24-valve DOHC V6 Direct injection 4-stroke gasoline engine Superior version (D-4S). This engine uses both direct injection and port injection systems. In addition, this engine uses the Variable Valve Timing-intelligent Wide (VVT-iW) control, Variable Valve Timing-intelligent (VVT-i) control, Direct Ignition System (DIS), and Electronic Throttle Control System-intelligent (ETCS-i). These control functions achieve improved engine performance, fuel economy, and clean emissions.



SPECIFICATION


a.

The specifications of the 2GR-FKS engine are shown in the following table.

Engine Type 2GR-FKS

*1: Models for Australia

*2: Models for Russia

*3: Emission regulations differ depending on the specifications of the vehicle.

*4: The figure shown is the weight of the part without coolant and oil.

No. of Cyls. & Arrangement 6-cylinder, V Type
Valve Mechanism 24-valve DOHC, Chain Drive
(with VVT-iW and VVT-i)
Combustion Chamber Pentroof Type
Flow of Intake and Exhaust Gasses Cross-flow
Fuel System Sequential Multiport Fuel Injection (SFI) D-4S
Ignition System Direct Ignition System (DIS)
Displacement cm3 (cu. in.) 3456 (210.9)
Bore X Stroke mm (in.) 94.0 X 83.0 (3.70 X 3.27)
Compression Ratio 11.8 : 1
Max. Output (EEC) kW@rpm 218@6600*1
186@5400*2
Max. Torque (EEC) N*m@rpm 350@4700*1
357@4700*2
Valve Timing Intake Open -33° to 42° BTDC
Closed 105° to 30° ABDC
Exhaust Open 22.5° to 64° BBDC
Closed 41.5° to 0° ATDC
Spark Plug Type DENSO Made FK20HBR8 (Iridium)
Plug Gap mm (in.) 0.7 to 0.8 (0.0276 to 0.0315)
Firing Order 1 - 2 - 3 - 4 - 5 - 6
Research Octane Number 91 or higher
Emission Regulation*3 EURO V
EURO Vb+
Engine Service Mass*4 (Reference) kg (lb) 167 (368)

Performance Curve (Models for Australia)
W135815E01
1.302,1.667 1.583,1.875 0.281,0.208 10 false 380 1.302,1.969 1.583,2.177 0.281,0.208 10 false 360 1.302,2.25 1.583,2.458 0.281,0.208 10 false 340 1.302,2.531 1.583,2.74 0.281,0.208 10 false 320 1.302,2.823 1.583,3.031 0.281,0.208 10 false 300 1.302,3.104 1.583,3.313 0.281,0.208 10 false 280 1.302,3.385 1.583,3.594 0.281,0.208 10 false 260 1.302,3.677 1.583,3.885 0.281,0.208 10 false 240 5.417,0.573 5.698,0.781 0.281,0.208 10 false 240 5.417,0.917 5.698,1.125 0.281,0.208 10 false 220 5.417,1.271 5.698,1.479 0.281,0.208 10 false 200 5.417,1.635 5.698,1.844 0.281,0.208 10 false 180 5.417,1.979 5.698,2.188 0.281,0.208 10 false 160 5.417,2.333 5.698,2.542 0.281,0.208 10 false 140 5.417,2.688 5.698,2.896 0.281,0.208 10 false 120 5.417,3.031 5.698,3.24 0.281,0.208 10 false 100 5.427,3.385 5.667,3.573 0.24,0.188 10 false 80 5.427,3.74 5.667,3.927 0.24,0.188 10 false 60 5.427,4.104 5.667,4.292 0.24,0.188 10 false 40 5.427,4.448 5.667,4.635 0.24,0.188 10 false 20 5.427,4.802 5.667,4.99 0.24,0.188 10 false 0 5.896,2.677 6.365,2.948 0.469,0.271 10 false Output 5.417,0.25 5.781,0.5 0.365,0.25 10 false (kW) 1.292,1.333 1.708,1.594 0.417,0.26 10 false (N*m) 0.573,2.635 1.083,2.885 0.51,0.25 10 false Torque 2.094,5.198 2.438,5.417 0.344,0.219 10 false 1000 2.521,5.198 2.865,5.417 0.344,0.219 10 false 2000 2.948,5.198 3.292,5.417 0.344,0.219 10 false 3000 3.385,5.198 3.729,5.417 0.344,0.219 10 false 4000 3.823,5.198 4.167,5.417 0.344,0.219 10 false 5000 4.24,5.198 4.583,5.417 0.344,0.219 10 false 6000 4.698,5.198 5.042,5.417 0.344,0.219 10 false 7000 5.156,5.167 5.5,5.385 0.344,0.219 10 false (rpm) 3.167,5.458 4.156,5.698 0.99,0.24 10 false Engine Speed

Performance Curve (Models for Russia)
W135816E01
1.281,1.688 1.583,1.885 0.302,0.198 10 false 380 1.281,1.969 1.583,2.167 0.302,0.198 10 false 360 1.281,2.26 1.583,2.458 0.302,0.198 10 false 340 1.281,2.542 1.583,2.74 0.302,0.198 10 false 320 1.281,2.823 1.583,3.021 0.302,0.198 10 false 300 1.281,3.115 1.583,3.313 0.302,0.198 10 false 280 1.281,3.396 1.583,3.594 0.302,0.198 10 false 260 5.417,0.573 5.719,0.771 0.302,0.198 10 false 240 5.417,0.917 5.719,1.115 0.302,0.198 10 false 220 5.417,1.281 5.719,1.479 0.302,0.198 10 false 200 5.417,1.635 5.719,1.833 0.302,0.198 10 false 180 5.417,1.979 5.719,2.177 0.302,0.198 10 false 160 5.417,2.333 5.719,2.531 0.302,0.198 10 false 140 5.417,2.688 5.719,2.885 0.302,0.198 10 false 120 5.417,3.042 5.719,3.24 0.302,0.198 10 false 100 5.417,3.406 5.719,3.604 0.302,0.198 10 false 80 5.417,3.75 5.719,3.948 0.302,0.198 10 false 60 5.417,4.115 5.719,4.313 0.302,0.198 10 false 40 5.417,4.458 5.719,4.656 0.302,0.198 10 false 20 5.417,4.813 5.719,5.01 0.302,0.198 10 false 0 1.281,3.688 1.583,3.885 0.302,0.198 10 false 240 1.271,1.26 1.698,1.5 0.427,0.24 10 false (N*m) 5.417,0.302 5.792,0.542 0.375,0.24 10 false (kW) 0.583,2.667 1.083,2.917 0.5,0.25 10 false Torque 5.979,2.667 6.479,2.917 0.5,0.25 10 false Output 2.104,5.208 2.448,5.417 0.344,0.208 10 false 1000 2.531,5.208 2.875,5.417 0.344,0.208 10 false 2000 2.958,5.208 3.302,5.417 0.344,0.208 10 false 3000 3.396,5.208 3.74,5.417 0.344,0.208 10 false 4000 3.823,5.208 4.167,5.417 0.344,0.208 10 false 5000 4.25,5.208 4.594,5.417 0.344,0.208 10 false 6000 4.688,5.208 5.031,5.417 0.344,0.208 10 false 7000 5.104,5.198 5.448,5.406 0.344,0.208 10 false (rpm) 3.083,5.458 4.052,5.656 0.969,0.198 10 false Engine Speed



MAIN FEATURES


a.

The 2GR-FKS engine has achieved the following through the use of the items listed in the table below.

i.

High performance and reliability


ii.

Low noise and vibration


iii.

Lightweight and compact design


iv.

Good serviceability


v.

Clean emissions and fuel economy

Item (1) (2) (3) (4) (5)

○: Applicable

-: Not applicable

*: Models with smart entry and start system

Engine Proper A steel-laminate type cylinder head gasket and No. 2 cylinder head gasket are used. ○ - - - -
A taper squish shape is used for the combustion chamber. ○ - - - ○
A cylinder block sub-assembly made of aluminum alloy is used. - - ○ - -
The skirt portion of each piston has a resin coating applied to reduce friction. ○ ○ - - ○
An oil pan sub-assembly made of aluminum alloy is used. - ○ ○ - -
Valve Mechanism Variable Valve Timing-intelligent Wide (VVT-iW) is used. ○ - - - ○
Variable Valve Timing-intelligent (VVT-i) is used. ○ - - - ○
Valve lash adjuster assemblies are used. ○ ○ - ○ -
A chain sub-assembly, No. 1 chain tensioner assembly (primary), and No. 2 chain tensioner assembly (secondary) are used. - ○ ○ ○ -
No. 1 valve rocker arm sub-assemblies are used. ○ - - - ○
Lubrication System An oil filter with a replaceable element is used. - - - ○ -
Cooling System TOYOTA Genuine Super Long Life Coolant (SLLC) is used. - - - ○ -
Intake and Exhaust Systems A linkless type throttle body with motor assembly is used. - - ○ ○ -
An intake air surge tank assembly made of plastic is used. - - ○ - -
Stainless steel exhaust manifold sub-assemblies (RH and LH) are used. - - ○ - ○
An ultra thin-wall, high-cell density ceramic type Three-Way Catalytic converter (TWC) is used. - - - - ○
Fuel System A returnless fuel system is used. ○ - - - ○
Compact 12-hole type fuel injector assemblies are used. ○ - ○ - ○
A Direct injection 4-stroke gasoline engine Superior version (D-4S) system is used. ○ - - - ○
1-hole slit nozzle type high pressure injector assemblies are used. ○ - - - ○
Quick connectors are used to connect the fuel hoses with the fuel pipes. - - - ○ -
Ignition System The Direct Ignition System (DIS) is used. ○ - ○ ○ ○
Long-reach type iridium-tipped spark plugs are used. ○ - - ○ ○
Charging System A generator clutch pulley with a one-way clutch is used. ○ - - - ○
A segment conductor type generator assembly is used. ○ - ○ - -
Starting System A Planetary reduction-Segment conductor motor (PS) type starter assembly is used. - - ○ - -
Serpentine Belt Drive System A serpentine belt drive system is used. - - ○ ○ -
Emission Control System An evaporative emission control system is used. - - - - ○
Engine Control System Magneto-Resistance Element (MRE) type camshaft position sensors are used. ○ - - - -
The Electronic Throttle Control System-intelligent (ETCS-i) is used. ○ - - - ○
An Acoustic Control Induction System (ACIS) is used. ○ - - - -
The cranking hold function is used.* ○ - - - -