Home › Engine / Hybrid System › 2GR-FKS ENGINE MECHANICAL › ENGINE UNIT › from 2016.11
NM3160E _51 Engine / Hybrid System _060957 2GR-FKS ENGINE MECHANICAL _0298832 ENGINE UNIT DE DETAILS F

2GR-FKS ENGINE MECHANICAL  ENGINE UNIT  DETAILS  CYLINDER BLOCK  


CONSTRUCTION


a.

The cylinder block sub-assembly is made of aluminum alloy, so it is lightweight.


b.

The cylinder block sub-assembly has a bank angle of 60°, a bank offset of 36.6 mm (1.441 in.) and a bore pitch of 105.5 mm (4.15 in.), resulting in a compact block (length and width) for its displacement.


c.

Installation bosses for the 2 knock control sensors are located on the inside of the left and right banks.


d.

Water passages are provided between the cylinder bores. By allowing the engine coolant to flow between the cylinder bores, this construction enables the temperature of the cylinder walls to be kept uniform.


e.

A compact block has been achieved by producing the thin cast-iron liners and cylinder block sub-assembly as a unit. It is not possible to rebore a block which uses this type of liner.


f.

The liners are a spiny-type, which have been manufactured so that their casting exterior forms large irregular surfaces in order to enhance the adhesion between the liners and the aluminum cylinder block sub-assembly. The enhanced adhesion helps heat dissipation, resulting in a lower overall temperature and reduced heat deformation of the cylinder bores.

W129337C04
2.583,0.167 4.25,1.833 1.667,1.667 3.667,0.583 3.917,0.25 3.917,0.25 4,0.25 true 2.833,1.5 3,1.5 3,1.5 3.333,1.167 true 3.667,1.333 4.083,1.333 true 5.625,2.635 5.833,1.5 5.833,1.5 5.917,1.5 true 6.167,1.583 6.083,1.583 6.083,1.583 5.802,2.917 true 3.583,5.583 3.417,5.583 3.417,5.583 3.021,4.875 true 4,0.167 4.25,0.323 0.25,0.156 10 false *1 2.688,1.417 3,1.573 0.313,0.156 10 false *2 2.604,0.177 2.833,0.333 0.229,0.156 10 false *a 4.083,1.229 4.25,1.396 0.167,0.167 10 false *b 5.938,1.417 6.25,1.573 0.313,0.156 10 false *c 3.615,5.49 3.927,5.646 0.313,0.156 10 false *d 6.208,1.5 6.417,1.656 0.208,0.156 10 false *c 3.167,2 3.323,2.198 0.156,0.198 10 false A 2.594,2.052 2.719,2.24 0.125,0.188 10 true A 0.917,1.667 1.188,1.844 0.271,0.177 10 false 60° 4.313,4.344 4.896,4.76 0.583,0.417 10 false 36.6 mm (1.44 in) 5.125,4.573 5.802,4.99 0.677,0.417 10 false 105.5 mm (4.15 in)
*1 Cylinder Block Sub-assembly *2 Liner
*a A-A Cross Section *b Irregularly Shaped Outer Casting Surface of Liner
*c Knock Control Sensor Boss *d Water Passage