Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function)
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095460 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27A5  Open in Front Floor Electrical Key Oscillator Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 1 indoor electrical key antenna assembly (front floor). For the No. 1 indoor electrical key antenna assembly (front floor) to detect when the electrical key transmitter sub-assembly is in the cabin, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A5 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor) (between terminals CLG5 and ANTE5, or terminals CG5B and CLGB).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A5 Open in Front Floor Electrical Key Oscillator Circuit An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor) (CLG5 - ANTE5, CG5B - CLGB) (1 trip detection logic*).
·

Certification ECU (smart key ECU assembly)

·

No. 1 indoor electrical key antenna assembly (front floor)

·

Wire harness or connector


DTC Output Confirmation Operation:

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
When electrical key transmitter sub-assembly is in front seat area:
·

Power source mode does not change when engine switch pressed

·

Electrical key transmitter sub-assembly locked inside vehicle


-

Related Data List and Active Test Item
DTC Code Data List and Active Test Item
B27A5 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

E270401E59
1.125,0.469 1.615,0.698 0.49,0.229 10 false ANTE5 1.177,0.917 1.677,1.094 0.5,0.177 10 false CLGB 5.365,0.354 5.594,0.542 0.229,0.188 10 false 21 5.354,0.813 5.583,1 0.229,0.188 10 false 20 5.646,0.448 6.115,0.646 0.469,0.198 10 false CLG5 5.646,0.906 6.26,1.104 0.615,0.198 10 false CG5B 5.365,1.26 5.667,1.458 0.302,0.198 10 false 11 0.313,1.625 2.51,2.01 2.198,0.385 10 false No. 1 Indoor Electrical Key Antenna Assembly (Front Floor) 0.323,1.49 0.823,1.667 0.5,0.177 10 false F39 5.646,1.385 5.948,1.583 0.302,0.198 10 false E 5.417,1.854 5.917,2.031 0.5,0.177 10 false F13 5.417,2 6.948,2.448 1.531,0.448 10 false Certification ECU (Smart Key ECU Assembly) 1.688,0.344 1.927,0.542 0.24,0.198 10 false 1 1.688,0.802 1.927,1 0.24,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to smart entry and start system (for Entry Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (front floor).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))
a.

Disconnect the F13 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F39 No. 1 indoor electrical key antenna assembly (front floor) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F13-21 (CLG5) - F39-1 (ANTE5) Always Below 1 Ω
F13-20 (CG5B) - F39-3 (CLGB) Always Below 1 Ω
F13-11 (E) - Body ground Always Below 1 Ω
F13-21 (CLG5) or F39-1 (ANTE5) - Body ground Always 10 kΩ or higher
F13-20 (CG5B) or F39-3 (CLGB) - Body ground Always 10 kΩ or higher



d.

Reconnect the F13 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR))
B343193C27
5.063,0.333 5.469,0.542 0.406,0.208 1.635,0.344 2.042,0.552 0.406,0.208 3.26,0.354 3.667,0.563 0.406,0.208 6.198,2.042 6.01,1.375 true 4.906,2.073 5.073,1.385 true 4.292,2.063 4.958,1.385 true 5.177,0.354 5.635,0.552 0.458,0.198 10 false F13 6.24,2.063 6.49,2.427 0.25,0.365 10 false E 1.125,2.76 1.594,3.135 0.469,0.375 10 false *b 4.125,2.135 4.594,2.51 0.469,0.375 10 false CLG5 0.573,0.115 0.823,0.479 0.25,0.365 10 false *a 4.74,2.146 5.208,2.521 0.469,0.375 10 false CG5B 0.781,3.688 1.25,4.063 0.469,0.375 10 false GND 1.563,4.375 2,4.563 0.438,0.188 10 false *c 2.323,4.396 2.76,4.583 0.438,0.188 10 false *d 1.74,0.365 2.198,0.563 0.458,0.198 10 false F10 3.375,0.375 3.833,0.573 0.458,0.198 10 false F12
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c For 30 seconds after closing any door using the door outside handle *d 30 seconds or more have elapsed after closing any door using the door outside handle


a.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
F13-21 (CLG5) - F13-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)
F13-20 (CG5B) - F13-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly not inside vehicle

3.

Within 30 seconds of closing any door using the door outside handle


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

4.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)
a.

Temporarily replace the No. 1 indoor electrical key antenna assembly (front floor) with a new one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Front Floor)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A5 is not output.



Result:
Proceed to
OK
NG



OK

END (NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)