Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function)
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0095460 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27A8  Open in Outside Luggage Compartment Electrical Key Antenna Circuit  


DESCRIPTION

The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the electrical key antenna (outside luggage compartment). For the electrical key antenna (outside luggage compartment) to detect when the electrical key transmitter sub-assembly is brought close to the vehicle, the received request signal is transmitted within approximately 1.0 m (3.28 ft.) of the back door. DTC B27A8 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment) (between terminals CLG8 and ANTE8, or terminals CG8B and CLGB).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A8 Open in Outside Luggage Compartment Electrical Key Antenna Circuit An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment) (CLG8 - ANTE8, CG8B - CLGB) (1 trip detection logic*).
·

Certification ECU (smart key ECU assembly)

·

Electrical key antenna (outside luggage compartment)

·

Wire harness or connector


DTC Output Confirmation Operation:

Any time



*: Only output while a malfunction is present and the engine switch on is (IG).


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry open/unlock operation cannot be performed for back door -

Related Data List and Active Test Item
DTC Code Data List and Active Test Item
B27A8 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

E270510E52
5.365,1.813 6.896,2.26 1.531,0.448 10 false Certification ECU (Smart Key ECU Assembly) 0.365,1.604 2.365,2.094 2,0.49 10 false Electrical Key Antenna (Outside Luggage Compartment) 0.354,1.448 0.688,1.615 0.333,0.167 10 false L24 1.115,0.458 1.688,0.625 0.573,0.167 10 false ANTE8 5.646,0.479 6.125,0.667 0.479,0.188 10 false CLG8 5.354,0.26 5.604,0.469 0.25,0.208 10 false 2 5.635,0.948 6.208,1.115 0.573,0.167 10 false CG8B 1.167,0.938 1.646,1.104 0.479,0.167 10 false CLGB 5.354,0.74 5.604,0.948 0.25,0.208 10 false 1 5.323,1.188 5.573,1.396 0.25,0.208 10 false 11 5.302,0.448 5.635,0.656 0.333,0.208 10 false F12 5.292,0.917 5.625,1.125 0.333,0.208 10 false F12 5.292,1.375 5.625,1.583 0.333,0.208 10 false F13 1.656,0.365 1.906,0.573 0.25,0.208 10 false 2 1.656,0.813 1.906,1.021 0.25,0.208 10 false 1 5.635,1.385 5.885,1.594 0.25,0.208 10 false E

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to smart entry and start system (for Entry Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and electrical key antenna (outside luggage compartment).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))
a.

Disconnect the F12 and F13 certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the L24 electrical key antenna (outside luggage compartment) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F12-2 (CLG8) - L24-2 (ANTE8) Always Below 1 Ω
F12-1 (CG8B) - L24-1 (CLGB) Always Below 1 Ω
F13-11 (E) - Body ground Always Below 1 Ω
F12-2 (CLG8) or L24-2 (ANTE8) - Body ground Always 10 kΩ or higher
F12-1 (CG8B) or L24-1 (CLGB) - Body ground Always 10 kΩ or higher



d.

Reconnect the F12 and F13 certification ECU (smart key ECU assembly) connectors.


Result:
Proceed to
OK
NG



OK

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))
B343195C10
3.313,0.313 3.708,0.552 0.396,0.24 5.104,0.313 5.5,0.552 0.396,0.24 1.688,0.344 2.083,0.583 0.396,0.24 6.188,2.063 6.031,1.396 true 4.26,1.25 4.729,2.115 true 4.167,1.25 3.958,2.104 true 4.563,2.167 5.177,2.365 0.615,0.198 10 false CG8B 3.792,2.156 4.406,2.354 0.615,0.198 10 false CLG8 6.177,2.115 6.792,2.313 0.615,0.198 10 false E 0.521,0.104 1.135,0.302 0.615,0.198 10 false *a 1.177,2.646 1.792,2.844 0.615,0.198 10 false *b 0.781,3.698 1.396,3.896 0.615,0.198 10 false GND 5.208,0.354 5.823,0.552 0.615,0.198 10 false F13 3.417,0.344 4.031,0.542 0.615,0.198 10 false F12 1.792,0.375 2.406,0.573 0.615,0.198 10 false F10
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1


a.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Condition Tool Setting Specified Condition
F12-2 (CLG8) - F13-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)
F12-1 (CG8B) - F13-11 (E) Procedure:
1.

Engine switch off

2.

Electrical key transmitter sub-assembly brought outside vehicle

3.

All doors closed

4.

Back door opener switch assembly off → on


2 V/DIV., 500 ms/DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

4.REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT)
a.

Temporarily replace the electrical key antenna (outside luggage compartment) with a new one.


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A8 is not output.



Result:
Proceed to
OK
NG



OK

END (ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)