Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2013.12–2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Turn the ignition switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.

·

Turn the ignition switch off before inspecting CAN bus lines for a ground short.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 1 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 1 CAN junction connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


i.

Connection diagram

C299930
3.979,1.135 3.979,0.271 3.979,0.271 2.563,0.271 true 4.24,1.135 4.24,0.479 4.24,0.479 5.521,0.479 true 4.531,1.135 4.531,0.708 4.531,0.708 5.833,0.708 true 2.594,2.219 3.979,2.219 3.979,2.219 3.979,1.25 true 4.24,1.25 4.24,2.135 4.24,2.135 5.521,2.135 true 4.531,1.26 4.531,1.865 4.531,1.865 5.833,1.865 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.979,0.177 2.896,0.375 0.917,0.198 10 false CANH*b 2.021,2.125 2.938,2.323 0.917,0.198 10 false CANL*b 5.635,0.396 6.552,0.594 0.917,0.198 10 false CANH*c 5.625,2.052 6.542,2.25 0.917,0.198 10 false CANL*c 5.948,0.625 6.865,0.823 0.917,0.198 10 false CANH*d 5.927,1.781 6.844,1.979 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(No. 1 CAN Junction Connector)
*b to Lane Departure Warning Camera
(w/ Lane Departure Alert System)
(for Sub Bus 2)
*c to Network Gateway ECU
(w/ Blind Spot Monitor System or Parking Assist Monitor System)
(for Sub Bus 2)
*d to No. 2 CAN Junction Connector
(for Sub Bus 2)



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F104-1 (CANH) BR No. 2 CAN junction connector
(for Sub bus 2)
F104-2 (CANL) W
F105-1 (CANH) L Network gateway ECU*1
(for Sub bus 2)
F105-2 (CANL) W
F108-1 (CANH) R Lane departure warning camera*2
(for Sub bus 2)
F108-2 (CANL) W

·

*1: w/ Blind Spot Monitor System or Parking Assist Monitor System

·

*2: w/ Lane Departure Alert System





NO. 2 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 2 CAN junction connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


i.

Connection diagram

C295152C04
2.625,1.208 2.635,0.813 2.635,0.813 1.5,0.813 true 2.625,1.333 2.625,2.063 2.625,2.063 1.5,2.063 true 2.896,1.198 2.906,0.552 2.906,0.552 2.01,0.552 true 3.177,1.188 3.177,0.292 3.177,0.292 4.521,0.292 true 2.906,1.323 2.906,2.417 2.906,2.417 2.063,2.417 true 3.448,1.198 3.448,0.667 3.448,0.667 4.969,0.667 true 3.177,1.333 3.177,2.427 3.177,2.427 4.552,2.427 true 3.448,1.323 3.448,2.135 3.448,2.135 4.969,2.135 true 0.042,0.042 0.354,0.24 0.313,0.198 10 false *a 0.927,0.719 1.844,0.917 0.917,0.198 10 false CANH*b 0.938,1.979 1.854,2.177 0.917,0.198 10 false CANL*b 1.427,0.469 2.344,0.667 0.917,0.198 10 false CANH*c 1.5,2.323 2.417,2.521 0.917,0.198 10 false CANL*c 4.594,0.208 5.51,0.406 0.917,0.198 10 false CANH*d 4.656,2.344 5.573,2.542 0.917,0.198 10 false CANL*d 5.042,2.042 5.958,2.24 0.917,0.198 10 false CANL*e 5.063,0.573 5.979,0.771 0.917,0.198 10 false CANH*e
*a Front view of wire harness connector
(No. 2 CAN Junction Connector)
*b to CAN Junction Terminal
(for Sub Bus 2)
*c to Blind Spot Monitor Sensor LH
(w/ Blind Spot Monitor System)
(for Sub Bus 2)
*d to Television Camera Assembly
(w/ Parking Assist Monitor System)
(for Sub Bus 2)
*e to No. 1 CAN Junction Connector
(for Sub Bus 2)
- -



ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
M38-1 (CANH) BR No. 1 CAN junction connector
(for Sub bus 2)
M38-2 (CANL) W
M39-1 (CANH) B Television camera assembly*1
(for Sub bus 2)
M39-2 (CANL) W
M40-1 (CANH) GR Blind spot monitor sensor LH*2
(for Sub bus 2)
M40-2 (CANL) W
M41-1 (CANH) B CAN junction terminal
(for Sub bus 2)
M41-2 (CANL) W

·

*1: w/ Parking Assist Monitor System

·

*2: w/ Blind Spot Monitor System





NO. 3 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 3 CAN junction connector.

i.

Connection diagram

C283770
3.177,0.104 3.667,0.396 0.49,0.292 1.667,1.833 1.927,1.833 1.927,1.833 2.344,2.135 true 1.708,2.625 1.948,2.625 1.948,2.625 2.354,2.302 true 1.667,1.469 2.01,1.469 2.01,1.469 2.604,2.094 true 1.813,3.01 2.125,3.01 2.125,3.01 2.646,2.323 true 1.802,1.042 2.135,1.042 2.135,1.042 2.885,2.104 true 1.99,3.323 2.385,3.323 2.385,3.323 2.906,2.323 true 2.208,0.635 2.458,0.635 2.458,0.635 3.146,2.104 true 2.438,3.542 2.771,3.542 2.771,3.542 3.167,2.333 true 3.75,0.594 3.51,0.594 3.51,0.594 3.385,2.115 true 4.458,0.74 4.26,0.74 4.26,0.74 3.635,2.115 true 5.24,0.969 5.021,0.969 5.021,0.969 4.135,2.125 true 3.74,3.552 3.448,3.552 3.448,3.552 3.396,2.313 true 4.354,3.365 4.115,3.365 4.115,3.365 3.667,2.323 true 5.177,3.208 4.917,3.208 4.917,3.208 4.135,2.313 true 5.583,1.333 5.333,1.333 5.333,1.333 4.385,2.125 true 5.583,2.917 5.333,2.917 5.333,2.917 4.396,2.313 true 0.094,0.063 0.51,0.396 0.417,0.333 10 false *a 1.083,1.74 1.698,1.969 0.615,0.229 10 false CANH*b 1.146,2.521 1.76,2.75 0.615,0.229 10 false CANL*b 1.083,1.375 1.698,1.604 0.615,0.229 10 false CANH*c 1.26,2.917 1.875,3.146 0.615,0.229 10 false CANL*c 1.229,0.948 1.844,1.177 0.615,0.229 10 false CANH*d 1.427,3.229 2.042,3.458 0.615,0.229 10 false CANL*d 1.635,0.542 2.5,0.771 0.865,0.229 10 false CANH*e 1.875,3.448 2.583,3.698 0.708,0.25 10 false CANL*e 3.823,0.5 4.438,0.729 0.615,0.229 10 false CANH*f 3.792,3.448 4.406,3.677 0.615,0.229 10 false CANL*f 4.531,0.646 5.146,0.875 0.615,0.229 10 false CANH*g 4.427,3.26 5.042,3.49 0.615,0.229 10 false CANL*g 5.333,0.885 5.948,1.115 0.615,0.229 10 false CANH*h 5.271,3.115 5.885,3.344 0.615,0.229 10 false CANL*h 3.271,0.156 3.885,0.354 0.615,0.198 10 false F102 5.667,1.25 6.281,1.479 0.615,0.229 10 false CANH*i 5.667,2.844 6.281,3.073 0.615,0.229 10 false CANL*i
*a Front view of wire harness connector
(No. 3 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
(for V Bus)
*c to ECM
(for V Bus)
*d to DLC3
(for V Bus)
*e to Steering Sensor
(for V Bus)
*f to Power Steering ECU Assembly
(for V Bus)
*g to Main Body ECU (Multiplex Network Body ECU)
(for V Bus)
*h to 4WD ECU Assembly
(for AWD)
(for V Bus)
*i to Headlight Leveling ECU Assembly
(w/ Automatic Headlight Beam Level Control System)
(for V Bus)
- -



ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F102-1 (CANH) BR No. 4 CAN junction connector
(for V bus)
F102-11 (CANL) W
F102-2 (CANH) B ECM
(for V bus)
F102-12 (CANL) W
F102-3 (CANH) V DLC3
(for V bus)
F102-13 (CANL) W
F102-4 (CANH) BE Steering sensor
(for V bus)
F102-14 (CANL) W
F102-5 (CANH) P Power steering ECU assembly
(for V bus)
F102-15 (CANL) W
F102-6 (CANH) R Main body ECU (multiplex network body ECU)
(for V bus)
F102-16 (CANL) W
F102-8 (CANH) L 4WD ECU assembly*1
(for V bus)
F102-18 (CANL) W
F102-9 (CANH) GR Headlight leveling ECU assembly*2
(for V bus)
F102-19 (CANL) W

·

*1: for AWD

·

*2: w/ Automatic Headlight Beam Level Control System





NO. 4 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 4 CAN junction connector.

i.

Connection diagram

C283770
3.177,0.104 3.667,0.396 0.49,0.292 1.667,1.833 1.927,1.833 1.927,1.833 2.344,2.135 true 1.708,2.625 1.948,2.625 1.948,2.625 2.354,2.302 true 1.667,1.469 2.01,1.469 2.01,1.469 2.604,2.094 true 1.813,3.01 2.125,3.01 2.125,3.01 2.646,2.323 true 1.802,1.042 2.135,1.042 2.135,1.042 2.885,2.104 true 1.99,3.323 2.385,3.323 2.385,3.323 2.906,2.323 true 2.208,0.635 2.458,0.635 2.458,0.635 3.146,2.104 true 2.438,3.542 2.771,3.542 2.771,3.542 3.167,2.333 true 4.5,0.583 4.25,0.583 4.25,0.583 3.635,2.115 true 4.75,0.917 4.5,0.917 4.5,0.917 3.896,2.115 true 4.5,3.5 4.25,3.5 4.25,3.5 3.667,2.323 true 4.75,3.188 4.5,3.188 4.5,3.188 3.896,2.323 true 5.167,2.927 4.917,2.927 4.917,2.927 4.146,2.313 true 5.104,1.26 4.896,1.26 4.896,1.26 4.125,2.094 true 5.25,1.646 5.083,1.646 5.083,1.646 4.635,2.104 true 5.25,2.646 5.083,2.646 5.083,2.646 4.656,2.323 true 0.094,0.063 0.51,0.396 0.417,0.333 10 false *a 1.104,1.75 1.719,1.979 0.615,0.229 10 false CANH*b 1.146,2.531 1.76,2.76 0.615,0.229 10 false CANL*b 1.094,1.375 1.708,1.604 0.615,0.229 10 false CANH*c 1.271,2.927 1.885,3.156 0.615,0.229 10 false CANL*c 1.25,0.948 1.865,1.177 0.615,0.229 10 false CANH*d 1.448,3.229 2.063,3.458 0.615,0.229 10 false CANL*d 1.646,0.542 2.26,0.771 0.615,0.229 10 false CANH*e 1.906,3.458 2.521,3.688 0.615,0.229 10 false CANL*e 4.573,0.49 5.375,0.74 0.802,0.25 10 false CANH*f 4.573,3.406 5.292,3.708 0.719,0.302 10 false CANL*f 5.198,1.177 5.813,1.406 0.615,0.229 10 false CANH*h 5.26,2.844 5.875,3.073 0.615,0.229 10 false CANL*h 3.271,0.167 3.885,0.365 0.615,0.198 10 false F103 5.344,1.563 5.958,1.792 0.615,0.229 10 false CANH*i 5.354,2.563 5.969,2.792 0.615,0.229 10 false CANL*i 4.844,0.833 5.458,1.063 0.615,0.229 10 false CANH*g 4.833,3.104 5.448,3.333 0.615,0.229 10 false CANL*g
*a Front view of wire harness connector
(No. 4 CAN Junction Connector)
*b to No. 3 CAN Junction Connector
(for V Bus)
*c to Skid Control ECU (Brake Actuator Assembly)
(for V Bus)
*d to Air Conditioning Amplifier Assembly
(for V Bus)
*e to Airbag Sensor Assembly
(for V Bus)
*f to Radio and Display Receiver Assembly
(for Radio and Display Type)
(for V Bus)
*g to Certification ECU (Smart Key ECU Assembly)
(w/ Smart Entry and Start System)
(for V Bus)
*h to Combination Meter Assembly
(for V Bus)
*i to Network Gateway ECU
(w/ Blind Spot Monitor System or Parking Assist Monitor System)
(for V Bus)
- -



ii.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F103-1 (CANH) BR No. 3 CAN junction connector
(for V bus)
F103-11 (CANL) W
F103-2 (CANH) GR Skid control ECU (brake actuator assembly)
(for V bus)
F103-12 (CANL) W
F103-3 (CANH) BE Air conditioning amplifier assembly
(for V bus)
F103-13 (CANL) W
F103-4 (CANH) Y Airbag sensor assembly
(for V bus)
F103-14 (CANL) W
F103-6 (CANH) L Radio and display receiver assembly*1
(for V bus)
F103-16 (CANL) W
F103-7 (CANH) G Certification ECU (smart key ECU assembly)*2
(for V bus)
F103-17 (CANL) W
F103-8 (CANH) SB Combination meter assembly
(for V bus)
F103-18 (CANL) W
F103-10 (CANH) P Network gateway ECU*3
(for V bus)
F103-20 (CANL) W

·

*1: for Radio and Display Type

·

*2: w/ Smart Entry and Start System

·

*3: w/ Blind Spot Monitor System or Parking Assist Monitor System





NO. 5 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 5 CAN junction connector.

i.

Connection diagram

C292404C05
3.177,0.302 3.594,0.625 0.417,0.323 2.729,1.698 2.188,0.885 2.188,0.885 2.042,0.885 true 2.979,1.698 2.51,0.552 2.51,0.552 2.375,0.552 true 3.25,1.698 4.219,0.74 4.219,0.74 4.448,0.74 true 3.24,1.927 4.219,2.469 4.219,2.469 4.448,2.469 true 2.469,2.448 2.583,2.448 2.583,2.448 2.99,1.917 true 2.167,2.229 2.281,2.229 2.281,2.229 2.719,1.906 true 3.115,1.688 2.729,0.26 2.729,0.26 2.573,0.26 true 2.667,2.646 2.781,2.646 2.781,2.646 3.115,1.927 true 0.063,0.031 0.375,0.229 0.313,0.198 10 false *a 3.24,0.365 3.615,0.563 0.375,0.198 10 false F111 1.469,0.792 2.385,0.99 0.917,0.198 10 false CANH*b 1.792,0.448 2.708,0.646 0.917,0.198 10 false CANH*c 2,0.156 2.917,0.354 0.917,0.198 10 false CANH*d 2.104,2.563 3.021,2.76 0.917,0.198 10 false CANL*d 1.885,2.354 2.802,2.552 0.917,0.198 10 false CANL*c 1.615,2.135 2.531,2.333 0.917,0.198 10 false CANL*b 4.542,0.646 5.458,0.844 0.917,0.198 10 false CANH*e 4.531,2.375 5.448,2.573 0.917,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Multiplex Network Door ECU
(w/ Power Back Door System)
(for Sub Bus 1)
*c to Position Control ECU and Switch Assembly
(w/ Seat Position Memory System)
(for Sub Bus 1)
*d to Outer Mirror Control ECU Assembly (for Driver Side)
(w/ Seat Position Memory System)
(for Sub Bus 1)
*e to No. 6 CAN Junction Connector
(for Sub Bus 1)
- -



ii.

Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F111-1 (CANH) L Multiplex network door ECU*1
(for Sub bus 1)
F111-12 (CANL) W
F111-3 (CANH) P Position control ECU and switch assembly*2
(for Sub bus 1)
F111-14 (CANL) W
F111-4 (CANH) SB Outer mirror control ECU assembly (for driver side)*2
(for Sub bus 1)
F111-15 (CANL) W
F111-5 (CANH) B No. 6 CAN junction connector
(for Sub bus 1)
F111-16 (CANL) W

·

*1: w/ Power Back Door System

·

*2: w/ Seat Position Memory System





NO. 6 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 6 CAN junction connector.

i.

Connection diagram

C292404C06
3.177,0.302 3.594,0.625 0.417,0.323 2.865,1.698 2.323,0.885 2.323,0.885 2.177,0.885 true 2.979,1.698 2.51,0.552 2.51,0.552 2.375,0.552 true 3.25,1.698 4.219,0.74 4.219,0.74 4.448,0.74 true 3.24,1.927 4.219,2.469 4.219,2.469 4.448,2.469 true 2.521,2.521 2.625,2.521 2.625,2.521 2.99,1.917 true 2.302,2.229 2.417,2.229 2.417,2.229 2.854,1.906 true 0.063,0.031 0.375,0.229 0.313,0.198 10 false *a 3.24,0.375 3.708,0.625 0.469,0.25 10 false F112 1.615,0.792 2.531,0.99 0.917,0.198 10 false CANH*b 1.792,0.448 2.708,0.646 0.917,0.198 10 false CANH*c 4.542,0.646 5.458,0.844 0.917,0.198 10 false CANH*d 4.542,2.365 5.458,2.563 0.917,0.198 10 false CANL*d 1.958,2.427 2.875,2.625 0.917,0.198 10 false CANL*c 1.75,2.135 2.667,2.333 0.917,0.198 10 false CANL*b
*a Front view of wire harness connector
(No. 6 CAN Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)
(for Sub Bus 1)
*c to Outer Mirror Control ECU Assembly (for Front Passenger Side)
(w/ Seat Position Memory System)
(for Sub Bus 1)
*d to No. 5 CAN Junction Connector
(for Sub Bus 1)



ii.

Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F112-2 (CANH) G Main body ECU (multiplex network body ECU)
(for Sub bus 1)
F112-13 (CANL) W
F112-3 (CANH) LG Outer mirror control ECU assembly (for front passenger side)*
(for Sub bus 1)
F112-14 (CANL) W
F112-5 (CANH) B No. 5 CAN junction connector
(for Sub bus 1)
F112-16 (CANL) W

*: w/ Seat Position Memory System




NO. 1 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 1 CAN junction connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


i.

Connection diagram

C295152
2.625,1.208 2.635,0.813 2.635,0.813 1.5,0.813 true 2.625,1.333 2.625,2.063 2.625,2.063 1.5,2.063 true 2.896,1.198 2.906,0.552 2.906,0.552 2.01,0.552 true 3.177,1.188 3.177,0.292 3.177,0.292 4.521,0.292 true 2.906,1.323 2.906,2.417 2.906,2.417 2.063,2.417 true 3.448,1.198 3.448,0.667 3.448,0.667 4.969,0.667 true 3.177,1.333 3.177,2.427 3.177,2.427 4.552,2.427 true 3.448,1.323 3.448,2.135 3.448,2.135 4.969,2.135 true 0.042,0.042 0.354,0.24 0.313,0.198 10 false *a 0.927,0.719 1.844,0.917 0.917,0.198 10 false CANH*b 0.938,1.979 1.854,2.177 0.917,0.198 10 false CANL*b 1.427,0.469 2.344,0.667 0.917,0.198 10 false CANH*c 1.5,2.323 2.417,2.521 0.917,0.198 10 false CANL*c 4.594,0.208 5.51,0.406 0.917,0.198 10 false CANH*d 4.656,2.344 5.573,2.542 0.917,0.198 10 false CANL*d 5.042,2.042 5.958,2.24 0.917,0.198 10 false CANL*e 5.063,0.573 5.979,0.771 0.917,0.198 10 false CANH*e
*a Front view of wire harness connector
(No. 1 CAN Junction Connector)
*b to Driving Support ECU Assembly
(w/ Pre-crash Safety System)
(for Sub Bus 2)
*c to Lane Departure Warning Camera
(w/ Lane Departure Alert System)
(for Sub Bus 2)
*d to Network Gateway ECU
(w/ Blind Spot Monitor System or Parking Assist Monitor System)
(for Sub Bus 2)
*e to No. 2 CAN Junction Connector
(for Sub Bus 2)
- -



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F104-1 (CANH) BR No. 2 CAN junction connector
(for Sub bus 2)
F104-2 (CANL) W
F105-1 (CANH) L Network gateway ECU*1
(for Sub bus 2)
F105-2 (CANL) W
F108-1 (CANH) R Lane departure warning camera*2
(for Sub bus 2)
F108-2 (CANL) W
F110-1 (CANH) G Driving support ECU assembly*3
(for Sub bus 1)
F110-2 (CANL) W

·

*1: w/ Blind Spot Monitor System or Parking Assist Monitor System

·

*2: w/ Lane Departure Alert System

·

*3: w/ Pre-crash Safety System





NO. 2 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 2 CAN junction connector.

HINT:

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


i.

Connection diagram

C295152
2.625,1.208 2.635,0.813 2.635,0.813 1.5,0.813 true 2.625,1.333 2.625,2.063 2.625,2.063 1.5,2.063 true 2.896,1.198 2.906,0.552 2.906,0.552 2.01,0.552 true 3.177,1.188 3.177,0.292 3.177,0.292 4.521,0.292 true 2.906,1.323 2.906,2.417 2.906,2.417 2.063,2.417 true 3.448,1.198 3.448,0.667 3.448,0.667 4.969,0.667 true 3.177,1.333 3.177,2.427 3.177,2.427 4.552,2.427 true 3.448,1.323 3.448,2.135 3.448,2.135 4.969,2.135 true 0.042,0.042 0.354,0.24 0.313,0.198 10 false *a 0.927,0.719 1.844,0.917 0.917,0.198 10 false CANH*b 0.938,1.979 1.854,2.177 0.917,0.198 10 false CANL*b 1.427,0.469 2.344,0.667 0.917,0.198 10 false CANH*c 1.5,2.323 2.417,2.521 0.917,0.198 10 false CANL*c 4.594,0.208 5.51,0.406 0.917,0.198 10 false CANH*d 4.656,2.344 5.573,2.542 0.917,0.198 10 false CANL*d 5.042,2.042 5.958,2.24 0.917,0.198 10 false CANL*e 5.063,0.573 5.979,0.771 0.917,0.198 10 false CANH*e
*a Front view of wire harness connector
(No. 2 CAN Junction Connector)
*b to CAN Junction Terminal
(for Sub Bus 2)
*c to Blind Spot Monitor Sensor LH
(w/ Blind Spot Monitor System)
(for Sub Bus 2)
*d to Television Camera Assembly
(w/ Parking Assist Monitor System)
(for Sub Bus 2)
*e to No. 1 CAN Junction Connector
(for Sub Bus 2)
- -



ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
M38-1 (CANH) BR No. 1 CAN junction connector
(for Sub bus 2)
M38-2 (CANL) W
M39-1 (CANH) B Television camera assembly*1
(for Sub bus 2)
M39-2 (CANL) W
M40-1 (CANH) GR Blind spot monitor sensor LH*2
(for Sub bus 2)
M40-2 (CANL) W
M41-1 (CANH) B CAN junction terminal
(for Sub bus 2)
M41-2 (CANL) W

·

*1: w/ Parking Assist Monitor System

·

*2: w/ Blind Spot Monitor System





NO. 3 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 3 CAN junction connector.

i.

Connection diagram

C283770
3.177,0.104 3.667,0.396 0.49,0.292 1.667,1.75 1.917,1.75 1.917,1.75 2.344,2.135 true 1.708,2.625 1.948,2.625 1.948,2.625 2.354,2.302 true 1.667,1.417 2,1.417 2,1.417 2.604,2.094 true 1.833,2.917 2.083,2.917 2.083,2.917 2.646,2.323 true 1.833,1.083 2.083,1.083 2.083,1.083 2.885,2.104 true 2,3.167 2.25,3.167 2.25,3.167 2.906,2.323 true 2.167,0.75 2.417,0.75 2.417,0.75 3.146,2.104 true 2.25,3.417 2.5,3.417 2.5,3.417 3.167,2.333 true 2.5,0.49 2.75,0.49 2.75,0.49 3.385,2.104 true 4.25,0.5 4,0.5 4,0.5 3.635,2.115 true 4.667,0.75 4.417,0.75 4.417,0.75 3.885,2.104 true 2.75,3.604 3,3.604 3,3.604 3.396,2.333 true 4.25,3.604 4,3.604 4,3.604 3.646,2.323 true 4.667,3.417 4.417,3.417 4.417,3.417 3.885,2.323 true 4.917,3.167 4.667,3.167 4.667,3.167 4.146,2.323 true 5.25,2.917 5,2.917 5,2.917 4.396,2.323 true 5.333,2.635 5.083,2.635 5.083,2.635 4.646,2.333 true 4.917,1.083 4.667,1.083 4.667,1.083 4.135,2.104 true 5.25,1.417 5,1.417 5,1.417 4.385,2.104 true 5.333,1.75 5.083,1.75 5.083,1.75 4.635,2.104 true 0.094,0.063 0.51,0.396 0.417,0.333 10 false *a 1.083,1.667 1.698,1.896 0.615,0.229 10 false CANH*b 1.146,2.521 1.76,2.75 0.615,0.229 10 false CANL*b 1.094,1.333 1.708,1.563 0.615,0.229 10 false CANH*c 1.271,2.813 1.885,3.042 0.615,0.229 10 false CANL*c 1.26,0.979 1.875,1.208 0.615,0.229 10 false CANH*d 1.448,3.073 2.063,3.302 0.615,0.229 10 false CANL*d 1.604,0.635 2.469,0.865 0.865,0.229 10 false CANH*e 1.708,3.323 2.417,3.573 0.708,0.25 10 false CANL*e 1.958,0.385 2.573,0.615 0.615,0.229 10 false CANH*f 2.25,3.51 2.865,3.74 0.615,0.229 10 false CANL*f 4.323,0.396 4.938,0.625 0.615,0.229 10 false CANH*g 4.323,3.51 4.938,3.74 0.615,0.229 10 false CANL*g 4.74,0.667 5.354,0.896 0.615,0.229 10 false CANH*h 4.74,3.323 5.354,3.552 0.615,0.229 10 false CANL*h 3.271,0.146 3.885,0.344 0.615,0.198 10 false F102 4.99,3.073 5.604,3.302 0.615,0.229 10 false CANL*i 5.323,2.823 5.938,3.052 0.615,0.229 10 false CANL*j 5.406,2.542 6.021,2.771 0.615,0.229 10 false CANL*k 4.99,0.99 5.604,1.219 0.615,0.229 10 false CANH*i 5.323,1.323 5.938,1.552 0.615,0.229 10 false CANH*j 5.406,1.656 6.021,1.885 0.615,0.229 10 false CANH*k
*a Front view of wire harness connector
(No. 3 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
(for V Bus)
*c to ECM
(for V Bus)
*d to Air Conditioning Amplifier Assembly
(for V Bus)
*e to Airbag Sensor Assembly
(for V Bus)
*f to Clearance Warning ECU Assembly
(w/ Toyota Parking Assist-sensor System)
(for V Bus)
*g to Main Body ECU (Multiplex Network Body ECU)
(for V Bus)
*h to Certification ECU (Smart Key ECU Assembly)
(w/ Smart Entry and Start System)
(for V Bus)
*i to 4WD ECU Assembly
(for AWD)
(for V Bus)
*j to Headlight Leveling ECU Assembly
(w/ Automatic Headlight Beam Level Control System)
(for V Bus)
*k to Network Gateway ECU
(w/ Blind Spot Monitor System or Parking Assist Monitor System)
(for V Bus)
- -



ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F102-1 (CANH) BR No. 4 CAN junction connector
(for V bus)
F102-11 (CANL) W
F102-2 (CANH) B ECM
(for V bus)
F102-12 (CANL) W
F102-3 (CANH) BE Air conditioning amplifier assembly
(for V bus)
F102-13 (CANL) W
F102-4 (CANH) Y Airbag sensor assembly
(for V bus)
F102-14 (CANL) W
F102-5 (CANH) LG Clearance warning ECU assembly*1
(for V bus)
F102-15 (CANL) W
F102-6 (CANH) R Main body ECU (multiplex network body ECU)
(for V bus)
F102-16 (CANL) W
F102-7 (CANH) G Certification ECU (smart key ECU assembly)*2
(for V bus)
F102-17 (CANL) W
F102-8 (CANH) L 4WD ECU assembly*3
(for V bus)
F102-18 (CANL) W
F102-9 (CANH) GR Headlight leveling ECU assembly*4
(for V bus)
F102-19 (CANL) W
F102-10 (CANH) P Network gateway ECU*5
(for V bus)
F102-20 (CANL) W

·

*1: w/ Toyota Parking Assist-sensor System

·

*2: w/ Smart Entry and Start System

·

*3: for AWD

·

*4: w/ Automatic Headlight Beam Level Control System

·

*5: w/ Blind Spot Monitor System or Parking Assist Monitor System





NO. 4 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 4 CAN junction connector.

i.

Connection diagram

C283770
3.177,0.104 3.667,0.396 0.49,0.292 1.667,1.833 1.927,1.833 1.927,1.833 2.344,2.135 true 1.708,2.625 1.948,2.625 1.948,2.625 2.354,2.302 true 1.667,1.469 2.01,1.469 2.01,1.469 2.604,2.094 true 1.813,3.01 2.125,3.01 2.125,3.01 2.646,2.323 true 1.802,1.042 2.135,1.042 2.135,1.042 2.885,2.104 true 1.99,3.323 2.385,3.323 2.385,3.323 2.906,2.323 true 2.208,0.635 2.458,0.635 2.458,0.635 3.146,2.104 true 2.438,3.542 2.771,3.542 2.771,3.542 3.167,2.333 true 3.75,0.594 3.51,0.594 3.51,0.594 3.385,2.115 true 4.552,0.833 4.333,0.833 4.333,0.833 3.635,2.115 true 3.74,3.552 3.448,3.552 3.448,3.552 3.396,2.313 true 4.417,3.25 4.167,3.25 4.167,3.25 3.667,2.323 true 5.01,2.948 4.656,2.948 4.656,2.948 4.146,2.313 true 5.104,1.26 4.896,1.26 4.896,1.26 4.125,2.094 true 0.094,0.063 0.51,0.396 0.417,0.333 10 false *a 1.104,1.75 1.719,1.979 0.615,0.229 10 false CANH*b 1.146,2.531 1.76,2.76 0.615,0.229 10 false CANL*b 1.094,1.375 1.708,1.604 0.615,0.229 10 false CANH*c 1.271,2.927 1.885,3.156 0.615,0.229 10 false CANL*c 1.25,0.948 1.865,1.177 0.615,0.229 10 false CANH*d 1.448,3.229 2.063,3.458 0.615,0.229 10 false CANL*d 1.646,0.542 2.26,0.771 0.615,0.229 10 false CANH*e 1.906,3.458 2.521,3.688 0.615,0.229 10 false CANL*e 3.823,0.5 4.438,0.729 0.615,0.229 10 false CANH*f 3.823,3.448 4.438,3.677 0.615,0.229 10 false CANL*f 4.615,0.75 5.417,1 0.802,0.25 10 false CANH*g*h 4.49,3.167 5.208,3.469 0.719,0.302 10 false CANL*g*h 3.281,0.156 3.896,0.354 0.615,0.198 10 false F103 5.177,1.167 5.792,1.396 0.615,0.229 10 false CANH*i 5.083,2.854 5.698,3.083 0.615,0.229 10 false CANL*i
*a Front view of wire harness connector
(No. 4 CAN Junction Connector)
*b to No. 3 CAN Junction Connector
(for V Bus)
*c to Skid Control ECU (Brake Actuator Assembly)
(for V Bus)
*d to DLC3
(for V Bus)
*e to Steering Sensor
(for V Bus)
*f to Power Steering ECU Assembly
(for V Bus)
*g to Navigation Receiver Assembly
(for Navigation Receiver Type)
(for V Bus)
*h to Radio and Display Receiver Assembly
(for Radio and Display Type)
(for V Bus)
*i to Combination Meter Assembly
(for V Bus)
- -



ii.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F103-1 (CANH) BR No. 3 CAN junction connector
(for V bus)
F103-11 (CANL) W
F103-2 (CANH) GR Skid control ECU (brake actuator assembly)
(for V bus)
F103-12 (CANL) W
F103-3 (CANH) V DLC3
(for V bus)
F103-13 (CANL) W
F103-4 (CANH) BE Steering sensor
(for V bus)
F103-14 (CANL) W
F103-5 (CANH) P Power steering ECU assembly
(for V bus)
F103-15 (CANL) W
F103-6 (CANH) L Navigation receiver assembly*1
(for V bus)
F103-16 (CANL) W
F103-6 (CANH) L Radio and display receiver assembly*2
(for V bus)
F103-16 (CANL) W
F103-8 (CANH) SB Combination meter assembly
(for V bus)
F103-18 (CANL) W

·

*1: for Navigation Receiver Type

·

*2: for Radio and Display Type





NO. 5 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 5 CAN junction connector.

i.

Connection diagram

C292404C03
3.177,0.302 3.594,0.625 0.417,0.323 2.729,1.698 2.188,0.885 2.188,0.885 2.042,0.885 true 3.115,1.698 2.646,0.552 2.646,0.552 2.51,0.552 true 3.25,1.698 4.219,0.74 4.219,0.74 4.448,0.74 true 3.24,1.927 4.219,2.469 4.219,2.469 4.448,2.469 true 2.594,2.448 2.708,2.448 2.708,2.448 3.115,1.917 true 2.167,2.229 2.281,2.229 2.281,2.229 2.719,1.906 true 0.063,0.031 0.375,0.229 0.313,0.198 10 false *a 3.24,0.354 3.667,0.552 0.427,0.198 10 false F111 1.469,0.792 2.385,0.99 0.917,0.198 10 false CANH*b 1.927,0.448 2.844,0.646 0.917,0.198 10 false CANH*c 2.01,2.354 2.927,2.552 0.917,0.198 10 false CANL*c 1.615,2.135 2.531,2.333 0.917,0.198 10 false CANL*b 4.542,0.646 5.458,0.844 0.917,0.198 10 false CANH*d 4.531,2.375 5.448,2.573 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to Multiplex Network Door ECU
(w/ Power Back Door System)
(for Sub Bus 1)
*c to Outer Mirror Control ECU Assembly (for Front Passenger Side)
(w/ Seat Position Memory System)
(for Sub Bus 1)
*d to No. 6 CAN Junction Connector
(for Sub Bus 1)



ii.

Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F111-1 (CANH) L Multiplex network door ECU*1
(for Sub bus 1)
F111-12 (CANL) W
F111-4 (CANH) SB Outer mirror control ECU assembly (for front passenger side)*2
(for Sub bus 1)
F111-15 (CANL) W
F111-5 (CANH) B No. 6 CAN junction connector
(for Sub bus 1)
F111-16 (CANL) W

·

*1: w/ Power Back Door System

·

*2: w/ Seat Position Memory System





NO. 6 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 6 CAN junction connector.

i.

Connection diagram

C292404C04
3.177,0.302 3.594,0.625 0.417,0.323 2.865,1.698 2.323,0.885 2.323,0.885 2.177,0.885 true 2.979,1.698 2.51,0.552 2.51,0.552 2.375,0.552 true 3.25,1.698 4.25,0.885 4.25,0.885 4.5,0.885 true 3.115,1.906 3.75,2.521 3.75,2.521 4,2.521 true 2.521,2.521 2.625,2.521 2.625,2.521 2.99,1.917 true 2.302,2.229 2.417,2.229 2.417,2.229 2.854,1.906 true 3.115,1.698 3.917,0.552 3.917,0.552 4.167,0.552 true 3.229,1.917 3.917,2.229 3.917,2.229 4.167,2.229 true 0.063,0.031 0.375,0.229 0.313,0.198 10 false *a 3.229,0.354 3.625,0.563 0.396,0.208 10 false F112 1.615,0.792 2.531,0.99 0.917,0.198 10 false CANH*b 1.792,0.448 2.708,0.646 0.917,0.198 10 false CANH*c 4.573,0.792 5.49,0.99 0.917,0.198 10 false CANH*e 4.24,2.135 5.156,2.333 0.917,0.198 10 false CANL*e 1.958,2.427 2.875,2.625 0.917,0.198 10 false CANL*c 1.75,2.135 2.667,2.333 0.917,0.198 10 false CANL*b 4.24,0.458 5.156,0.656 0.917,0.198 10 false CANH*d 4.073,2.427 4.99,2.625 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(No. 6 CAN Junction Connector)
*b to Main Body ECU (Multiplex Network Body ECU)
(for Sub Bus 1)
*c to Outer Mirror Control ECU Assembly (for Driver Side)
(w/ Seat Position Memory System)
(for Sub Bus 1)
*d to Position Control ECU and Switch Assembly
(w/ Seat Position Memory System)
(for Sub Bus 1)
*e to No. 5 CAN Junction Connector
(for Sub Bus 1)
- -



ii.

Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F112-2 (CANH) G Main body ECU (multiplex network body ECU)
(for Sub bus 1)
F112-13 (CANL) W
F112-3 (CANH) LG Outer mirror control ECU assembly (for driver side)*
(for Sub bus 1)
F112-14 (CANL) W
F112-4 (CANH) P Position control ECU and switch assembly*
(for Sub bus 1)
F112-15 (CANL) W
F112-5 (CANH) B No. 5 CAN junction connector
(for Sub bus 1)
F112-16 (CANL) W

*: w/ Seat Position Memory System




CAN JUNCTION TERMINAL


a.

Check the CAN junction terminal.

i.

Connection diagram

C285687C10
2.208,0.188 2.656,0.479 0.448,0.292 3.792,0.917 4.229,1.354 4.229,1.354 4.417,1.354 true 2.979,1.365 3.177,1.365 3.177,1.365 3.583,0.917 true 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 2.302,0.229 2.917,0.427 0.615,0.198 10 false M42 4.458,1.25 5.073,1.448 0.615,0.198 10 false CANH*b 2.448,1.271 3.063,1.469 0.615,0.198 10 false CANL*b
*a Front view of wire harness connector
(to CAN Junction Terminal)
*b to No. 2 CAN Junction Connector
(for Sub Bus 2)



ii.

Check the connection diagram of the components which are connected to the CAN junction terminal.

Terminal No. (Symbol) Wiring Color Connected to
M42-3 (CANH) B No. 2 CAN junction connector
(for Sub bus 2)
M42-2 (CANL) W




DLC3


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C292402C01
3.354,0.052 3.75,0.344 0.396,0.292 3.479,0.708 3.115,0.271 3.115,0.271 2.979,0.271 true 3.833,1.24 3.281,1.625 3.281,1.625 3.135,1.625 true 4.698,1.573 4.542,1.573 4.542,1.573 4.208,1.219 true 4.396,0.24 4.25,0.24 4.25,0.24 3.844,0.719 true 0.073,0.073 0.385,0.271 0.313,0.198 10 false *1 3.427,0.104 3.74,0.302 0.313,0.198 10 false F25 2.708,0.177 3.021,0.375 0.313,0.198 10 false CG 2.719,1.531 3.333,1.729 0.615,0.198 10 false CANL 4.792,1.479 5.25,1.677 0.458,0.198 10 false BAT 4.49,0.146 5.104,0.344 0.615,0.198 10 false CANH
*1 DLC3 - -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F25-6 (CANH) - F25-14 (CANL) V - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F25-6 (CANH) - F25-4 (CG) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F25-14 (CANL) - F25-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F25-6 (CANH) - F25-16 (BAT) V - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F25-14 (CANL) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM (for 1AR-FE)


C289291
2.24,0.052 2.635,0.344 0.396,0.292 5.76,0.042 6.156,0.333 0.396,0.292 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 2.354,0.094 2.813,0.292 0.458,0.198 10 false C1 5.833,0.083 6.292,0.281 0.458,0.198 10 false A43
*a Component without harness connected
(ECM)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A43 and C1 ECM connectors.

C289292C01
1.719,0.042 2.146,0.333 0.427,0.292 4.75,0.042 5.177,0.333 0.427,0.292 1.531,0.76 1.01,0.281 1.01,0.281 0.917,0.281 true 2.51,0.75 2.844,0.188 2.844,0.188 2.927,0.188 true 2.51,0.813 2.792,1.427 2.792,1.427 2.896,1.427 true 4.813,0.771 4.448,0.229 4.448,0.229 4.323,0.229 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 0.49,0.208 1.104,0.406 0.615,0.198 10 false BATT 1.813,0.083 2.271,0.281 0.458,0.198 10 false A43 2.99,0.104 3.604,0.302 0.615,0.198 10 false CANH 2.979,1.344 3.594,1.542 0.615,0.198 10 false CANL 4.875,0.094 5.333,0.292 0.458,0.198 10 false C1 4.094,0.135 4.406,0.333 0.313,0.198 10 false E1
*a Front view of wire harness connector
(to ECM)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A43-13 (CANH) - A43-26 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A43-13 (CANH) - C1-16 (E1) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A43-26 (CANL) - C1-16 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A43-13 (CANH) - A43-1 (BATT) B - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A43-26 (CANL) - A43-1 (BATT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM (for 2GR-FE)


C289291
2.24,0.052 2.635,0.344 0.396,0.292 5.76,0.042 6.156,0.333 0.396,0.292 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 2.354,0.094 2.813,0.292 0.458,0.198 10 false C1 5.833,0.083 6.292,0.281 0.458,0.198 10 false A43
*a Component without harness connected
(ECM)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A43 and C1 ECM connectors.

C289292
1.719,0.042 2.146,0.333 0.427,0.292 4.75,0.042 5.177,0.333 0.427,0.292 1.531,0.76 1.01,0.281 1.01,0.281 0.917,0.281 true 2.51,0.75 2.844,0.188 2.844,0.188 2.927,0.188 true 2.51,0.813 2.792,1.427 2.792,1.427 2.896,1.427 true 5.031,0.844 5.427,0.344 5.427,0.344 5.563,0.344 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 0.49,0.208 1.104,0.406 0.615,0.198 10 false BATT 1.813,0.083 2.271,0.281 0.458,0.198 10 false A43 2.99,0.104 3.604,0.302 0.615,0.198 10 false CANH 2.979,1.344 3.594,1.542 0.615,0.198 10 false CANL 4.875,0.094 5.333,0.292 0.458,0.198 10 false C1 5.615,0.25 5.927,0.448 0.313,0.198 10 false E1
*a Front view of wire harness connector
(to ECM)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A43-13 (CANH) - A43-26 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A43-13 (CANH) - C1-49 (E1) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A43-26 (CANL) - C1-49 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A43-13 (CANH) - A43-1 (BATT) B - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A43-26 (CANL) - A43-1 (BATT) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


C298412
2.104,0.063 2.521,0.323 0.417,0.26 4.958,0.083 5.375,0.344 0.417,0.26 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 2.188,0.104 2.646,0.302 0.458,0.198 10 false F22 5.042,0.125 5.5,0.323 0.458,0.198 10 false F21
*a Component without harness connected
(Combination Meter Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F22 combination meter assembly connector.

C295058
3.354,0.104 3.792,0.354 0.438,0.25 2.823,1.656 2.906,1.656 2.906,1.656 3.365,1.125 true 2.688,1.479 2.854,1.479 2.854,1.479 3.219,1.115 true 2.365,0.667 2.49,0.667 2.49,0.667 2.802,0.906 true 3.76,1.104 4.177,1.563 4.177,1.563 4.292,1.563 true 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 3.448,0.135 3.906,0.333 0.458,0.198 10 false F22 2.208,0.573 2.365,0.771 0.156,0.198 10 false B 2.385,1.552 3,1.75 0.615,0.198 10 false CANH 2.271,1.385 2.885,1.583 0.615,0.198 10 false CANL 4.365,1.458 4.677,1.656 0.313,0.198 10 false ES
*a Front view of wire harness connector
(to Combination Meter Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F22-17 (CANH) - F22-16 (CANL) SB - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
F22-17 (CANH) - F22-20 (ES) SB - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F22-16 (CANL) - F22-20 (ES) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F22-17 (CANH) - F22-1 (B) SB - P HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F22-16 (CANL) - F22-1 (B) W - P LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


B357834
1.094,3.417 1.458,3.667 0.365,0.25 3.583,3.385 3.948,3.635 0.365,0.25 5.927,3.385 6.292,3.635 0.365,0.25 1.385,4.823 1.75,5.073 0.365,0.25 3.958,4.802 4.323,5.052 0.365,0.25 5.583,4.948 5.948,5.198 0.365,0.25 6.469,5.01 6.833,5.26 0.365,0.25 4.969,6.427 5.333,6.677 0.365,0.25 1.385,6.469 1.75,6.719 0.365,0.25 3.542,7.979 3.906,8.229 0.365,0.25 2.104,0.594 2.104,0.24 2.104,0.24 2.24,0.24 false 1.656,2.844 1.656,1.104 1.656,1.104 2.021,1.104 false 1.656,1.656 2.021,1.656 false 1.656,2.146 2.021,2.146 false 2.156,2.146 2.385,2.146 false 2.156,1.656 2.385,1.656 false 2.146,1.104 2.375,1.104 false 4.635,0.552 4.635,0.208 4.635,0.208 4.76,0.208 false 0.135,0.063 0.51,0.302 0.375,0.24 12 false *a 0.552,1.063 0.865,1.26 0.313,0.198 10 false 4H 0.552,1.792 0.865,1.99 0.313,0.198 10 false 4F 0.563,2.24 0.875,2.438 0.313,0.198 10 false 4K 0.833,2.479 1.146,2.677 0.313,0.198 10 false 4L 2.302,0.135 2.615,0.333 0.313,0.198 10 false *1 2.448,1 2.76,1.198 0.313,0.198 10 false F20 2.458,1.552 2.771,1.75 0.313,0.198 10 false F19 2.458,2.042 2.771,2.24 0.313,0.198 10 false F18 1.583,2.875 1.896,3.073 0.313,0.198 10 false *2 4.833,0.115 5.146,0.313 0.313,0.198 10 false MB 6.458,0.927 6.771,1.125 0.313,0.198 10 false 4D 6.458,1.708 6.771,1.906 0.313,0.198 10 false 4A 1.167,3.427 1.479,3.625 0.313,0.198 10 false F18 3.656,3.406 3.969,3.604 0.313,0.198 10 false F19 6,3.406 6.313,3.604 0.313,0.198 10 false F20 1.49,4.844 1.802,5.042 0.313,0.198 10 false 4H 4.063,4.823 4.375,5.021 0.313,0.198 10 false 4F 5.677,4.969 5.99,5.167 0.313,0.198 10 false 4K 6.583,5.031 6.896,5.229 0.313,0.198 10 false 4L 1.49,6.49 1.802,6.688 0.313,0.198 10 false 4D 5.063,6.458 5.375,6.656 0.313,0.198 10 false 4A 3.625,8.021 3.938,8.219 0.313,0.198 10 false MB
*1 Main Body ECU (Multiplex Network Body ECU) *2 3 Connectors
*a Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU))
- -


B357833
1.844,3.5 2.188,3.74 0.344,0.24 5.042,3.5 5.385,3.74 0.344,0.24 1.427,4.833 1.771,5.073 0.344,0.24 4.031,4.875 4.375,5.115 0.344,0.24 5.615,4.938 5.958,5.177 0.344,0.24 6.5,5.01 6.844,5.25 0.344,0.24 5.042,6.469 5.385,6.708 0.344,0.24 1.458,6.5 1.802,6.74 0.344,0.24 3.49,8.021 3.833,8.26 0.344,0.24 2.083,0.604 2.083,0.219 2.083,0.219 2.229,0.219 false 2.146,1.615 2.375,1.615 false 1.688,2.625 1.688,1.615 1.688,1.615 2.01,1.615 false 2.156,2.104 2.385,2.104 false 1.688,2.104 2.021,2.104 false 4.656,0.542 4.656,0.156 4.656,0.156 4.802,0.156 false 0.083,0.083 0.531,0.375 0.448,0.292 12 false *a 0.552,1.01 0.865,1.208 0.313,0.198 10 false 4H 0.552,1.771 0.865,1.969 0.313,0.198 10 false 4F 0.563,2.229 0.875,2.427 0.313,0.198 10 false 4K 0.833,2.49 1.146,2.688 0.313,0.198 10 false 4L 2.302,0.125 2.615,0.323 0.313,0.198 10 false *1 2.448,1.521 2.76,1.719 0.313,0.198 10 false F19 2.458,2.01 2.771,2.208 0.313,0.198 10 false F18 1.604,2.656 1.917,2.854 0.313,0.198 10 false *2 4.885,0.063 5.198,0.26 0.313,0.198 10 false MB 6.469,0.917 6.781,1.115 0.313,0.198 10 false 4D 6.469,1.708 6.781,1.906 0.313,0.198 10 false 4A 1.896,3.521 2.208,3.719 0.313,0.198 10 false F18 5.104,3.51 5.417,3.708 0.313,0.198 10 false F19 1.521,4.854 1.833,5.052 0.313,0.198 10 false 4H 4.125,4.896 4.438,5.094 0.313,0.198 10 false 4F 5.698,4.958 6.01,5.156 0.313,0.198 10 false 4K 6.594,5.031 6.906,5.229 0.313,0.198 10 false 4L 1.542,6.521 1.854,6.719 0.313,0.198 10 false 4D 5.125,6.49 5.438,6.688 0.313,0.198 10 false 4A 3.563,8.042 3.875,8.24 0.313,0.198 10 false MB
*1 Main Body ECU (Multiplex Network Body ECU) *2 2 Connectors
*a Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU))
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F18 and F19 main body ECU (multiplex network body ECU) connectors.

C292339C01
2.031,0.292 2.448,0.604 0.417,0.313 4.698,0.313 5.115,0.625 0.417,0.313 2.104,2.51 2.521,2.823 0.417,0.313 2.052,1.198 2.74,0.417 2.74,0.417 2.844,0.417 true 2.135,1.198 2.969,0.635 2.969,0.635 3.083,0.635 true 5.021,1.188 5.708,0.406 5.708,0.406 5.813,0.406 true 5.104,1.198 5.938,0.635 5.938,0.635 6.052,0.635 true 3.573,2.49 4.115,2.021 4.115,2.021 4.26,2.021 true 4.281,3.01 4,3.448 4,3.448 3.885,3.448 true 1.104,0.115 1.417,0.313 0.313,0.198 10 false *a 1.927,1.979 2.24,2.177 0.313,0.198 10 false *1 2.135,0.344 2.448,0.542 0.313,0.198 10 false F18 4.802,0.354 5.115,0.552 0.313,0.198 10 false F19 2.198,2.552 2.51,2.75 0.313,0.198 10 false F25 2.906,0.333 3.521,0.531 0.615,0.198 10 false CANP 3.146,0.552 3.76,0.75 0.615,0.198 10 false CANN 5.885,0.323 6.5,0.521 0.615,0.198 10 false CANL 6.115,0.552 6.729,0.75 0.615,0.198 10 false CANH 4.344,1.938 4.656,2.135 0.313,0.198 10 false CG 3.563,3.365 4.021,3.563 0.458,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F19-14 (CANH) - F19-13 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F19-14 (CANH) - F25-4 (CG) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F19-13 (CANL) - F25-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F19-14 (CANH) - F25-16 (BAT) R - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F19-13 (CANL) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Sub Bus 1 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F18-9 (CANP) - F18-10 (CANN) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
F18-9 (CANP) - F25-4 (CG) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F18-10 (CANN) - F25-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F18-9 (CANP) - F25-16 (BAT) G - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F18-10 (CANN) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)


C292334
1.823,0.729 2.229,1.052 0.406,0.323 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 1.906,0.792 2.365,0.99 0.458,0.198 10 false A47
*a Component without harness connected
(Skid Control ECU (Brake Actuator Assembly))
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A47 skid control ECU (brake actuator assembly) connector.

C292335
1.854,0.771 2.281,1.104 0.427,0.333 3.063,0.792 2.49,0.271 2.49,0.271 2.385,0.271 true 4.833,0.427 4.698,0.427 4.698,0.427 4.083,0.781 true 4.24,0.188 4.115,0.188 4.115,0.188 3.26,0.969 true 4.5,1.656 4.396,1.656 4.396,1.656 3.26,1.042 true 0.052,0.031 0.365,0.229 0.313,0.198 10 false *a 1.948,0.833 2.406,1.031 0.458,0.198 10 false A47 1.958,0.177 2.573,0.375 0.615,0.198 10 false GND1 4.927,0.333 5.385,0.531 0.458,0.198 10 false +BS 4.323,0.104 4.938,0.302 0.615,0.198 10 false CANL 4.583,1.563 5.198,1.76 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A47-25 (CANH) - A47-14 (CANL) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A47-25 (CANH) - A47-1 (GND1) GR - W HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A47-14 (CANL) - A47-1 (GND1) W - W LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A47-25 (CANH) - A47-12 (+BS) GR - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A47-14 (CANL) - A47-12 (+BS) W - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




STEERING SENSOR


C292358C01
3.521,0.094 3.938,0.406 0.417,0.313 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 3.615,0.135 4.073,0.333 0.458,0.198 10 false F58
*a Component without harness connected
(Steering Sensor)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F58 steering sensor connector.

C292359C01
2.385,0.219 2.781,0.552 0.396,0.333 3.896,1.229 4.375,0.854 4.375,0.854 4.51,0.854 true 3.573,1.24 4.167,1.646 4.167,1.646 4.292,1.646 true 2.708,1.063 2.833,1.063 2.833,1.063 3.26,1.219 true 2.823,1.573 2.927,1.573 2.927,1.573 3.427,1.25 true 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a 2.469,0.281 2.927,0.479 0.458,0.198 10 false F58 4.604,0.771 5.063,0.969 0.458,0.198 10 false BAT 4.375,1.563 4.99,1.76 0.615,0.198 10 false CANH 2.354,0.979 2.813,1.177 0.458,0.198 10 false ESS 2.396,1.5 3.01,1.698 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Steering Sensor)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F58-3 (CANH) - F58-2 (CANL) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F58-3 (CANH) - F58-1 (ESS) BE - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F58-2 (CANL) - F58-1 (ESS) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F58-3 (CANH) - F58-5 (BAT) BE - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F58-2 (CANL) - F58-5 (BAT) W - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


C292351
1.854,0.865 2.188,1.104 0.333,0.24 0.781,1.313 1.083,1.542 0.302,0.229 1.146,1.313 1.448,1.542 0.302,0.229 1.51,1.313 1.813,1.542 0.302,0.229 0.646,3.458 0.948,3.688 0.302,0.229 3.729,0.177 4.063,0.406 0.333,0.229 5.677,0.146 6.01,0.375 0.333,0.229 4.698,1.677 5.031,1.906 0.333,0.229 5.521,1.677 5.854,1.906 0.333,0.229 3.885,1.698 4.219,1.927 0.333,0.229 2.021,0.854 2.021,0.781 false 0.927,1.313 1.031,1.135 true 1.292,1.313 1.292,1.146 true 1.625,1.313 1.573,1.146 true 0.948,3.51 1.073,3.479 false 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 1.979,0.875 2.292,1.073 0.313,0.198 10 false p2 0.875,1.323 1.188,1.521 0.313,0.198 10 false p1 1.25,1.313 1.406,1.51 0.156,0.198 10 false a 1.635,1.333 1.792,1.531 0.156,0.198 10 false b 0.76,3.458 0.917,3.656 0.156,0.198 10 false c 3.833,0.188 4.146,0.385 0.313,0.198 10 false p2 5.656,1.688 5.813,1.885 0.156,0.198 10 false b 4.833,1.677 4.99,1.875 0.156,0.198 10 false a 3.99,1.708 4.302,1.906 0.313,0.198 10 false p1 5.813,0.146 5.969,0.344 0.156,0.198 10 false c
*a Component without harness connected
(Power Steering ECU Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the p1 and p2 power steering ECU assembly connectors.

C292352C01
1.083,0.865 1.479,1.156 0.396,0.292 4.865,0.167 5.26,0.458 0.396,0.292 2.302,1.281 2.656,0.76 2.656,0.76 2.76,0.76 true 2.302,1.479 2.719,1.26 2.719,1.26 2.844,1.26 true 5.479,1.104 5.885,0.896 5.885,0.896 6,0.896 true 4.156,0.938 4.26,0.938 4.26,0.938 4.594,1.104 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 1.208,0.896 1.521,1.094 0.313,0.198 10 false p1 5,0.198 5.313,0.396 0.313,0.198 10 false p2 2.844,0.667 3.458,0.865 0.615,0.198 10 false CANH 2.927,1.177 3.542,1.375 0.615,0.198 10 false CANL 3.844,0.833 4.302,1.031 0.458,0.198 10 false PIG 6.104,0.813 6.719,1.01 0.615,0.198 10 false PGND
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
p1-4 (CANH) - p1-8 (CANL) W - B HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
p1-4 (CANH) - p2-2 (PGND) W - B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
p1-8 (CANL) - p2-2 (PGND) B - B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
p1-4 (CANH) - p2-1 (PIG) W - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
p1-8 (CANL) - p2-1 (PIG) B - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIRBAG SENSOR ASSEMBLY


C292355
1.75,0.083 2.156,0.354 0.406,0.271 3.396,0.063 3.802,0.333 0.406,0.271 4.938,0.073 5.344,0.344 0.406,0.271 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.865,0.115 2.323,0.313 0.458,0.198 10 false M7 3.479,0.094 3.938,0.292 0.458,0.198 10 false F38 5.073,0.104 5.385,0.302 0.313,0.198 10 false L9
*a Component without harness connected
(Airbag Sensor Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F38 airbag sensor assembly connector.

C292356C01
1.51,0.177 1.938,0.479 0.427,0.302 4.885,0.146 5.292,0.458 0.406,0.313 1.521,1.052 1.115,0.385 1.115,0.385 1.01,0.385 true 0.969,1.583 1.094,1.583 1.094,1.583 1.406,1.271 true 1.698,1.271 1.948,1.656 1.948,1.656 2.073,1.656 true 5.698,1.323 6.083,1.625 6.083,1.625 6.219,1.625 true 0.365,0.083 0.677,0.281 0.313,0.198 10 false *a 1.604,0.24 2.063,0.438 0.458,0.198 10 false F38 0.563,0.292 1.177,0.49 0.615,0.198 10 false CANH 0.521,1.479 1.135,1.677 0.615,0.198 10 false CANL 2.146,1.552 2.458,1.75 0.313,0.198 10 false E1 3.677,0.104 3.99,0.302 0.313,0.198 10 false *1 4.969,0.198 5.281,0.396 0.313,0.198 10 false F25 6.302,1.531 6.76,1.729 0.458,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F38-13 (CANH) - F38-22 (CANL) Y - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F38-13 (CANH) - F38-25 (E1) Y - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F38-22 (CANL) - F38-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F38-13 (CANH) - F25-16 (BAT) Y - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F38-22 (CANL) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


E285436
3.792,0.167 4.167,0.385 0.375,0.219 2,0.156 2.375,0.375 0.375,0.219 5.229,0.188 5.521,0.385 0.292,0.198 3.854,0.198 4.313,0.396 0.458,0.198 10 false F80 2.073,0.177 2.531,0.375 0.458,0.198 10 false F81 5.302,0.198 5.76,0.396 0.458,0.198 10 false z3 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a
*a Component without harness connected
(Air Conditioning Amplifier Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F80 air conditioning amplifier assembly connector.

C292365C01
2.573,0.25 2.99,0.552 0.417,0.302 3.729,1.229 4.521,0.688 4.521,0.688 4.677,0.688 true 3.625,1.229 4.448,0.417 4.448,0.417 4.594,0.417 true 3.906,1.24 4.688,0.927 4.688,0.927 4.802,0.927 true 2.365,1.542 2.479,1.542 2.479,1.542 2.677,1.365 true 2.667,0.292 3.125,0.49 0.458,0.198 10 false F80 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 2.208,1.438 2.365,1.635 0.156,0.198 10 false B 4.875,0.844 5.333,1.042 0.458,0.198 10 false GND 4.688,0.323 5.302,0.521 0.615,0.198 10 false CANH 4.76,0.594 5.375,0.792 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F80-11 (CANH) - F80-12 (CANL) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F80-11 (CANH) - F80-14 (GND) BE - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F80-12 (CANL) - F80-14 (GND) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F80-11 (CANH) - F80-21 (B) BE - P HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F80-12 (CANL) - F80-21 (B) W - P LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System)


C292361
5.01,0.063 5.427,0.365 0.417,0.302 3.323,0.052 3.74,0.354 0.417,0.302 1.667,0.063 2.083,0.365 0.417,0.302 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 5.104,0.104 5.563,0.302 0.458,0.198 10 false F13 1.76,0.104 2.219,0.302 0.458,0.198 10 false F10 3.406,0.094 3.719,0.292 0.313,0.198 10 false F12
*a Component without harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F13 certification ECU (smart key ECU assembly) connector.

C292362C01
3.365,0.104 3.792,0.396 0.427,0.292 2.24,1.438 2.365,1.438 2.365,1.438 2.771,1.021 true 4.073,0.865 4.427,0.281 4.427,0.281 4.552,0.281 true 4.198,0.865 4.635,0.479 4.635,0.479 4.74,0.479 true 4.448,0.854 4.729,1.083 4.729,1.083 4.854,1.083 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 3.469,0.146 3.927,0.344 0.458,0.198 10 false F13 2.094,1.323 2.25,1.521 0.156,0.198 10 false E 4.635,0.188 5.25,0.385 0.615,0.198 10 false CANH 4.833,0.385 5.448,0.583 0.615,0.198 10 false CANL 4.906,0.979 5.219,1.177 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F13-7 (CANH) - F13-8 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F13-7 (CANH) - F13-11 (E) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F13-8 (CANL) - F13-11 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F13-7 (CANH) - F13-10 (+B) G - GR HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F13-8 (CANL) - F13-10 (+B) W - GR LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type)


E286964
1.333,0.521 1.74,0.75 0.406,0.229 3.208,0.521 3.615,0.75 0.406,0.229 4.917,0.521 5.323,0.75 0.406,0.229 5.719,0.521 6.125,0.75 0.406,0.229 2.25,2.021 2.656,2.25 0.406,0.229 3.313,2.021 3.719,2.25 0.406,0.229 4.219,1.938 4.625,2.167 0.406,0.229 1.385,0.542 1.844,0.74 0.458,0.198 10 false F117 3.26,0.542 3.719,0.74 0.458,0.198 10 false F116 4.969,0.542 5.427,0.74 0.458,0.198 10 false F114 5.771,0.542 6.229,0.74 0.458,0.198 10 false F115 2.302,2.052 2.76,2.25 0.458,0.198 10 false F118 3.365,2.042 3.823,2.24 0.458,0.198 10 false F119 4.323,1.969 4.781,2.167 0.458,0.198 10 false RA 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a
*a Component without harness connected
(Navigation Receiver Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F114 and F116 navigation receiver assembly connectors.

C292346C01
4.969,0.042 5.396,0.365 0.427,0.323 1.708,0.052 2.135,0.375 0.427,0.323 2.115,1.115 2.854,0.615 2.854,0.615 2.979,0.615 true 2.021,1.104 2.698,0.156 2.698,0.156 2.813,0.156 true 5.021,1.26 4.677,1.646 4.677,1.646 4.365,1.646 true 6.156,0.563 6.021,0.563 6.021,0.563 5.646,0.938 true 0.052,0.031 0.365,0.229 0.313,0.198 10 false *a 1.771,0.115 2.229,0.313 0.458,0.198 10 false F116 5.031,0.094 5.563,0.302 0.531,0.208 10 false F114 2.896,0.063 3.51,0.26 0.615,0.198 10 false CANH 3.073,0.521 3.688,0.719 0.615,0.198 10 false CANL 3.927,1.531 4.542,1.729 0.615,0.198 10 false GND1 6.24,0.469 6.698,0.667 0.458,0.198 10 false +B1
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F116-9 (CANH) - F116-10 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F116-9 (CANH) - F114-7 (GND1) L - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F116-10 (CANL) - F114-7 (GND1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F116-9 (CANH) - F114-4 (+B1) L - SB HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F116-10 (CANL) - F114-4 (+B1) W - SB LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


E286745
1.531,0.135 1.948,0.354 0.417,0.219 3.406,0.229 3.823,0.448 0.417,0.219 5.323,0.135 5.74,0.354 0.417,0.219 0.563,1.625 0.875,1.844 0.313,0.219 1.365,1.635 1.677,1.854 0.313,0.219 6.177,1.385 6.49,1.604 0.313,0.219 2.438,1.646 2.75,1.865 0.313,0.219 3.573,1.708 3.885,1.927 0.313,0.219 4.49,1.573 4.885,1.823 0.396,0.25 5.229,1.604 5.542,1.823 0.313,0.219 1.625,0.156 2.083,0.354 0.458,0.198 10 false F72 3.5,0.25 3.958,0.448 0.458,0.198 10 false F73 5.417,0.167 5.875,0.365 0.458,0.198 10 false F71 0.604,1.646 1.063,1.844 0.458,0.198 10 false F69 1.406,1.656 1.865,1.854 0.458,0.198 10 false F70 6.24,1.417 6.698,1.615 0.458,0.198 10 false RA 2.531,1.667 2.99,1.865 0.458,0.198 10 false n3 3.656,1.729 4.115,1.927 0.458,0.198 10 false n1 4.542,1.615 5,1.813 0.458,0.198 10 false F113 5.313,1.625 5.771,1.823 0.458,0.198 10 false n6 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a
*a Component without harness connected
(Radio and Display Receiver Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F69 and F71 radio and display receiver assembly connectors.

C292346C06
4.969,0.042 5.396,0.365 0.427,0.323 1.708,0.052 2.135,0.375 0.427,0.323 2.115,1.115 2.854,0.615 2.854,0.615 2.979,0.615 true 2.021,1.104 2.698,0.156 2.698,0.156 2.813,0.156 true 5.021,1.26 4.677,1.646 4.677,1.646 4.365,1.646 true 6.156,0.563 6.021,0.563 6.021,0.563 5.646,0.938 true 0.052,0.031 0.365,0.229 0.313,0.198 10 false *a 1.802,0.115 2.26,0.313 0.458,0.198 10 false F71 5.063,0.104 5.594,0.313 0.531,0.208 10 false F69 2.896,0.063 3.51,0.26 0.615,0.198 10 false CANH 3.073,0.521 3.688,0.719 0.615,0.198 10 false CANL 3.927,1.531 4.542,1.729 0.615,0.198 10 false GND1 6.24,0.469 6.698,0.667 0.458,0.198 10 false +B1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F71-9 (CANH) - F71-10 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F71-9 (CANH) - F69-7 (GND1) L - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F71-10 (CANL) - F69-7 (GND1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F71-9 (CANH) - F69-4 (+B1) L - SB HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F71-10 (CANL) - F69-4 (+B1) W - SB LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




NETWORK GATEWAY ECU (w/ Blind Spot Monitor System or Parking Assist Monitor System)


C292376
3.302,0.073 3.698,0.344 0.396,0.271 0.083,0.042 0.396,0.24 0.313,0.198 10 false *a 3.375,0.115 3.833,0.313 0.458,0.198 10 false F85
*a Component without harness connected
(Network Gateway ECU)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F85 network gateway ECU connector.

C292377
3.375,0.052 3.76,0.313 0.385,0.26 3.969,1.083 4.594,0.49 4.594,0.49 4.771,0.49 true 4.083,1.24 4.74,0.958 4.74,0.958 4.875,0.958 true 3.979,1.25 4.25,1.542 4.25,1.542 4.375,1.542 true 3.427,1.656 3.563,1.656 3.563,1.656 3.781,1.24 true 3.094,0.458 3.25,0.458 3.25,0.458 3.688,1.229 true 2.792,0.823 2.927,0.823 2.927,0.823 3.198,1.094 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 3.438,0.083 3.896,0.281 0.458,0.198 10 false F85 4.844,0.406 5.302,0.604 0.458,0.198 10 false GND 4.948,0.885 5.563,1.083 0.615,0.198 10 false CA1H 4.448,1.458 5.063,1.656 0.615,0.198 10 false CA1L 3,1.563 3.615,1.76 0.615,0.198 10 false CA2H 2.688,0.375 3.302,0.573 0.615,0.198 10 false CA2L 2.396,0.74 3.01,0.938 0.615,0.198 10 false BATT
*a Front view of wire harness connector
(to Network Gateway ECU)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F85-16 (CA1H) - F85-15 (CA1L) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F85-16 (CA1H) - F85-4 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F85-15 (CA1L) - F85-4 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F85-16 (CA1H) - F85-2 (BATT) P - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F85-15 (CA1L) - F85-2 (BATT) W - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Sub Bus 2 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F85-13 (CA2H) - F85-12 (CA2L) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
F85-13 (CA2H) - F85-4 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F85-12 (CA2L) - F85-4 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F85-13 (CA2H) - F85-2 (BATT) L - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F85-12 (CA2L) - F85-2 (BATT) W - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CLEARANCE WARNING ECU ASSEMBLY (w/ Toyota Parking Assist-sensor System)


C292373
3.365,0.125 3.792,0.438 0.427,0.313 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 3.458,0.177 3.917,0.375 0.458,0.198 10 false F87
*a Component without harness connected
(Clearance Warning ECU Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F87 clearance warning ECU assembly connector.

C292374C01
1.667,0.167 2.094,0.469 0.427,0.302 4.823,0.052 5.25,0.354 0.427,0.302 2.813,0.875 2.927,0.344 2.927,0.344 3.01,0.344 true 1.406,1.51 1.51,1.51 1.51,1.51 1.698,1.01 true 2.917,0.875 3.125,0.698 3.125,0.698 3.219,0.698 true 5.667,1.167 5.99,1.583 5.99,1.583 6.104,1.583 true 0.344,0.156 0.656,0.354 0.313,0.198 10 false *a 3.542,0.135 3.854,0.333 0.313,0.198 10 false *1 1.76,0.208 2.219,0.406 0.458,0.198 10 false F87 3.292,0.604 3.604,0.802 0.313,0.198 10 false R2 3.073,0.25 3.385,0.448 0.313,0.198 10 false R1 1.26,1.417 1.417,1.615 0.156,0.198 10 false E 4.917,0.104 5.229,0.302 0.313,0.198 10 false F25 6.188,1.479 6.646,1.677 0.458,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F87-17 (R1) - F87-18 (R2) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F87-17 (R1) - F87-27 (E) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F87-18 (R2) - F87-27 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F87-17 (R1) - F25-16 (BAT) LG - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F87-18 (R2) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




4WD ECU ASSEMBLY (for AWD)


C292370
3.417,0.104 3.823,0.406 0.406,0.302 0.094,0.073 0.406,0.271 0.313,0.198 10 false *a 3.5,0.156 3.958,0.354 0.458,0.198 10 false F14
*a Component without harness connected
(4WD ECU Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F14 4WD ECU assembly connector.

C292371C01
1.938,0.083 2.365,0.396 0.427,0.313 4.792,0.073 5.219,0.385 0.427,0.313 2.813,0.875 3.073,0.281 3.073,0.281 3.177,0.281 true 1.542,1.063 1.823,1.521 1.823,1.521 2.021,1.521 true 1.427,1.073 1.25,1.521 1.25,1.521 1.125,1.521 true 5.646,1.156 5.927,1.615 5.927,1.615 6.125,1.615 true 0.885,0.104 1.198,0.302 0.313,0.198 10 false *a 3.646,0.094 3.958,0.292 0.313,0.198 10 false *1 2.031,0.146 2.49,0.344 0.458,0.198 10 false F14 4.885,0.135 5.198,0.333 0.313,0.198 10 false F25 3.25,0.188 3.708,0.385 0.458,0.198 10 false GND 2.104,1.427 2.719,1.625 0.615,0.198 10 false CANH 0.688,1.438 1.302,1.635 0.615,0.198 10 false CANL 6.198,1.531 6.656,1.729 0.458,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to 4WD ECU Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F14-6 (CANH) - F14-5 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F14-6 (CANH) - F14-4 (GND) L - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F14-5 (CANL) - F14-4 (GND) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F14-6 (CANH) - F25-16 (BAT) L - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F14-5 (CANL) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




HEADLIGHT LEVELING ECU ASSEMBLY (w/ Automatic Headlight Beam Level Control System)


E101528
3.292,0.063 3.688,0.375 0.396,0.313 0.063,0.052 0.385,0.313 0.323,0.26 10 false *a 3.365,0.115 3.792,0.365 0.427,0.25 10 false A67
*a Component without harness connected
(Headlight Leveling ECU Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A67 headlight leveling ECU assembly connector.

C295181C01
2.052,0.115 2.479,0.396 0.427,0.281 5,0.083 5.427,0.365 0.427,0.281 5.865,1.25 6.385,1.51 6.385,1.51 6.531,1.51 true 2.625,0.896 2.896,0.313 2.896,0.313 3,0.313 true 2.729,0.896 3.063,0.5 3.063,0.5 3.188,0.5 true 2.938,0.906 3.229,1.135 3.229,1.135 3.344,1.135 true 0.979,0.104 1.292,0.302 0.313,0.198 10 false *a 2.135,0.156 2.594,0.354 0.458,0.198 10 false A67 5.094,0.125 5.406,0.323 0.313,0.198 10 false F25 3.917,0.094 4.229,0.292 0.313,0.198 10 false *1 6.615,1.427 7.073,1.625 0.458,0.198 10 false BAT 3.063,0.219 3.677,0.417 0.615,0.198 10 false CANH 3.26,0.406 3.875,0.604 0.615,0.198 10 false CANL 3.438,1.042 3.75,1.24 0.313,0.198 10 false E1
*1 DLC3 - -
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A67-6 (CANH) - A67-7 (CANL) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A67-6 (CANH) - A67-9 (E1) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A67-7 (CANL) - A67-9 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A67-6 (CANH) - F25-16 (BAT) GR - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A67-7 (CANL) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY (for Driver Side) (w/ Seat Position Memory System)


C269560
3.969,0.042 4.344,0.271 0.375,0.229 2.885,0.042 3.26,0.271 0.375,0.229 3.979,0.323 4.344,0.531 0.365,0.208 2.896,0.323 3.26,0.531 0.365,0.208 4.115,0.052 4.406,0.271 0.292,0.219 10 false I2 2.958,0.052 3.354,0.333 0.396,0.281 10 false z10 0.063,0.031 0.563,0.479 0.5,0.448 10 false *a 3.313,0.063 3.719,0.323 0.406,0.26 10 false *A 3.313,0.333 3.719,0.594 0.406,0.26 10 false *B 3.01,0.323 3.406,0.604 0.396,0.281 10 false z9 4.083,0.323 4.583,0.656 0.5,0.333 10 false H2 4.396,0.073 4.802,0.333 0.406,0.26 10 false *A 4.406,0.344 4.813,0.604 0.406,0.26 10 false *B
*A for LHD *B for RHD
*a Component without harness connected
(Outer Mirror Control ECU Assembly (for Driver Side))
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H2 or I2 outer mirror control ECU assembly (for driver side) connector.

C292392C01
2.125,0.583 2.552,0.865 0.427,0.281 2.125,0.917 2.552,1.198 0.427,0.281 3.792,0.906 4.24,0.302 4.24,0.302 4.344,0.302 true 3.927,0.896 4.354,0.698 4.354,0.698 4.49,0.698 true 2.854,1.552 2.927,1.552 2.927,1.552 3.208,1.115 true 3.323,1.125 3.552,1.531 3.552,1.531 3.656,1.531 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 2.292,0.625 2.75,0.823 0.458,0.198 10 false I2 2.26,0.958 2.573,1.156 0.313,0.198 10 false H2 2.646,0.615 2.958,0.813 0.313,0.198 10 false *A 2.646,0.938 2.958,1.135 0.313,0.198 10 false *B 4.417,0.208 5.031,0.406 0.615,0.198 10 false CPUB 4.552,0.604 5.01,0.802 0.458,0.198 10 false GND 2.417,1.458 3.031,1.656 0.615,0.198 10 false CANN 3.74,1.427 4.354,1.625 0.615,0.198 10 false CANP
*A for LHD *B for RHD
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Driver Side))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I2-9 (CANP) - I2-8 (CANN) SB - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I2-9 (CANP) - I2-7 (GND) SB - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I2-8 (CANN) - I2-7 (GND) P - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I2-9 (CANP) - I2-6 (CPUB) SB - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I2-8 (CANN) - I2-6 (CPUB) P - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H2-9 (CANP) - H2-8 (CANN) SB - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H2-9 (CANP) - H2-7 (GND) SB - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H2-8 (CANN) - H2-7 (GND) V - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H2-9 (CANP) - H2-6 (CPUB) SB - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H2-8 (CANN) - H2-6 (CPUB) V - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




OUTER MIRROR CONTROL ECU ASSEMBLY (for Front Passenger Side) (w/ Seat Position Memory System)


C269560
3.979,0.042 4.354,0.25 0.375,0.208 2.885,0.042 3.26,0.25 0.375,0.208 3.979,0.313 4.354,0.521 0.375,0.208 2.885,0.313 3.26,0.521 0.375,0.208 4.083,0.042 4.542,0.323 0.458,0.281 10 false H2 3,0.042 3.458,0.333 0.458,0.292 10 false z9 0.052,0.042 0.417,0.333 0.365,0.292 10 false *a 4.125,0.323 4.583,0.604 0.458,0.281 10 false I2 2.969,0.323 3.427,0.615 0.458,0.292 10 false z10 3.323,0.052 3.688,0.344 0.365,0.292 10 false *A 4.417,0.344 4.781,0.635 0.365,0.292 10 false *B 4.417,0.052 4.781,0.344 0.365,0.292 10 false *A 3.323,0.344 3.688,0.635 0.365,0.292 10 false *B
*A for LHD *B for RHD
*a Component without harness connected
(Outer Mirror Control ECU Assembly (for Front Passenger Side))
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H2 or I2 outer mirror control ECU assembly (for front passenger side) connector.

C292392C02
2.125,0.583 2.552,0.865 0.427,0.281 2.125,0.917 2.552,1.198 0.427,0.281 3.792,0.906 4.24,0.302 4.24,0.302 4.344,0.302 true 3.927,0.896 4.354,0.698 4.354,0.698 4.49,0.698 true 2.854,1.552 2.927,1.552 2.927,1.552 3.208,1.115 true 3.323,1.125 3.552,1.531 3.552,1.531 3.656,1.531 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 2.292,0.958 2.75,1.156 0.458,0.198 10 false I2 2.26,0.625 2.573,0.823 0.313,0.198 10 false H2 2.646,0.615 2.958,0.813 0.313,0.198 10 false *A 2.646,0.938 2.958,1.135 0.313,0.198 10 false *B 4.417,0.208 5.031,0.406 0.615,0.198 10 false CPUB 4.552,0.604 5.01,0.802 0.458,0.198 10 false GND 2.417,1.458 3.031,1.656 0.615,0.198 10 false CANN 3.74,1.427 4.354,1.625 0.615,0.198 10 false CANP
*A for LHD *B for RHD
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly (for Front Passenger Side))
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
H2-9 (CANP) - H2-8 (CANN) SB - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
H2-9 (CANP) - H2-7 (GND) SB - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H2-8 (CANN) - H2-7 (GND) V - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
H2-9 (CANP) - H2-6 (CPUB) SB - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
H2-8 (CANN) - H2-6 (CPUB) V - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
I2-9 (CANP) - I2-8 (CANN) SB - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
I2-9 (CANP) - I2-7 (GND) SB - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I2-8 (CANN) - I2-7 (GND) P - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
I2-9 (CANP) - I2-6 (CPUB) SB - BE HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
I2-8 (CANN) - I2-6 (CPUB) P - BE LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




POSITION CONTROL ECU AND SWITCH ASSEMBLY (for LHD w/ Seat Position Memory System)


B219506
4.052,0.198 4.427,0.427 0.375,0.229 2.99,0.208 3.365,0.438 0.375,0.229 4.167,0.208 4.594,0.49 0.427,0.281 10 false e7 3.104,0.219 3.448,0.49 0.344,0.271 10 false e6 0.063,0.073 0.49,0.396 0.427,0.323 10 false *a
*a Component without harness connected
(Position Control ECU and Switch Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the e6 and e7 position control ECU and switch assembly connectors.

C292395C05
1.427,0.135 1.854,0.469 0.427,0.333 4.125,0.104 4.552,0.438 0.427,0.333 1.823,1.042 1.385,0.781 1.385,0.781 1.25,0.781 true 1.323,1.604 1.49,1.604 1.49,1.604 1.813,1.292 true 4.656,1.323 4.469,1.594 4.469,1.594 4.375,1.594 true 4.771,1.344 5.385,1.625 5.385,1.625 5.5,1.625 true 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 1.573,0.208 2.031,0.406 0.458,0.198 10 false e6 0.885,0.698 1.365,0.896 0.479,0.198 10 false GND 1.073,1.521 1.406,1.719 0.333,0.198 10 false +B 4.271,0.167 4.729,0.365 0.458,0.198 10 false e7 3.948,1.5 4.563,1.698 0.615,0.198 10 false CANN 5.573,1.531 6.188,1.729 0.615,0.198 10 false CANP
*a Front view of wire harness connector
(to Position Control ECU and Switch Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
e7-8 (CANP) - e7-7 (CANN) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
e7-8 (CANP) - e6-2 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
e7-7 (CANN) - e6-2 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
e7-8 (CANP) - e6-7 (+B) L - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
e7-7 (CANN) - e6-7 (+B) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




POSITION CONTROL ECU AND SWITCH ASSEMBLY (for RHD w/ Seat Position Memory System)


B345462
2.583,0.083 2.917,0.292 0.333,0.208 3.833,0.083 4.167,0.292 0.333,0.208 2.677,0.094 3.01,0.406 0.333,0.313 10 false d7 3.917,0.094 4.271,0.365 0.354,0.271 10 false d6 0.063,0.052 0.396,0.333 0.333,0.281 10 false *a
*a Component without harness connected
(Position Control ECU and Switch Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the d6 and d7 position control ECU and switch assembly connectors.

C292395C03
1.427,0.135 1.854,0.469 0.427,0.333 4.125,0.104 4.552,0.438 0.427,0.333 1.823,1.042 1.385,0.781 1.385,0.781 1.25,0.781 true 1.323,1.604 1.49,1.604 1.49,1.604 1.813,1.292 true 4.656,1.323 4.469,1.594 4.469,1.594 4.375,1.594 true 4.771,1.344 5.385,1.625 5.385,1.625 5.5,1.625 true 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 1.583,0.208 2.042,0.406 0.458,0.198 10 false d6 0.875,0.688 1.385,0.885 0.51,0.198 10 false GND 1.063,1.51 1.438,1.719 0.375,0.208 10 false +B 4.271,0.167 4.729,0.365 0.458,0.198 10 false d7 3.948,1.5 4.563,1.698 0.615,0.198 10 false CANN 5.573,1.531 6.188,1.729 0.615,0.198 10 false CANP
*a Front view of wire harness connector
(to Position Control ECU and Switch Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
d7-8 (CANP) - d7-7 (CANN) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
d7-8 (CANP) - d6-2 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
d7-7 (CANN) - d6-2 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
d7-8 (CANP) - d6-7 (+B) L - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
d7-7 (CANN) - d6-7 (+B) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door System)


C294682
2.052,0.135 2.469,0.438 0.417,0.302 4.677,0.146 5.094,0.448 0.417,0.302 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 2.188,0.188 2.646,0.385 0.458,0.198 10 false X7 4.813,0.198 5.271,0.396 0.458,0.198 10 false X6
*a Component without harness connected
(Multiplex Network Door ECU)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the X6 and X7 multiplex network door ECU connectors.

C295246C01
1.792,0.115 2.208,0.396 0.417,0.281 5.177,0.115 5.594,0.396 0.417,0.281 4.156,1.469 4.292,1.469 4.292,1.469 4.573,1.052 true 4.906,1.49 4.771,1.49 4.771,1.49 4.677,1.052 true 1.469,1.479 1.604,1.479 1.604,1.479 1.885,1.063 true 2.396,1.469 2.26,1.469 2.26,1.469 2.063,1.063 true 1.938,0.156 2.396,0.354 0.458,0.198 10 false X7 5.313,0.156 5.771,0.354 0.458,0.198 10 false X6 3.729,1.365 4.344,1.563 0.615,0.198 10 false CANP 4.979,1.385 5.594,1.583 0.615,0.198 10 false CANN 1.115,1.385 1.573,1.583 0.458,0.198 10 false GND 2.49,1.375 2.646,1.573 0.156,0.198 10 false B 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Multiplex Network Door ECU)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
X6-13 (CANP) - X6-14 (CANN) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
X6-13 (CANP) - X7-7 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
X6-14 (CANN) - X7-7 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
X6-13 (CANP) - X7-8 (B) L - G HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
X6-14 (CANN) - X7-8 (B) W - G LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)


C292385
3.385,0.052 3.792,0.333 0.406,0.281 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 3.458,0.104 3.917,0.302 0.458,0.198 10 false M31
*a Component without harness connected
(Blind Spot Monitor Sensor LH)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the M31 blind spot monitor sensor LH connector.

C292415C01
4.875,0.094 5.271,0.375 0.396,0.281 1.854,0.115 2.26,0.396 0.406,0.281 1.438,0.5 1.51,0.5 1.51,0.5 1.948,1.021 true 1.583,1.604 1.688,1.604 1.688,1.604 1.948,1.167 true 2.323,1.177 2.563,1.573 2.563,1.573 2.667,1.573 true 5.698,1.188 5.938,1.583 5.938,1.583 6.042,1.583 true 0.74,0.146 1.052,0.344 0.313,0.198 10 false *a 3.552,0.115 3.865,0.313 0.313,0.198 10 false *1 4.948,0.135 5.26,0.333 0.313,0.198 10 false F25 1.927,0.146 2.385,0.344 0.458,0.198 10 false M31 1.031,0.396 1.646,0.594 0.615,0.198 10 false CA1P 1.167,1.5 1.781,1.698 0.615,0.198 10 false CA1N 2.74,1.469 3.354,1.667 0.615,0.198 10 false BLGD 6.125,1.479 6.583,1.677 0.458,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M31-2 (CA1P) - M31-7 (CA1N) GR - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
M31-2 (CA1P) - M31-10 (BLGD) GR - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
M31-7 (CA1N) - M31-10 (BLGD) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
M31-2 (CA1P) - F25-16 (BAT) GR - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M31-7 (CA1N) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




DRIVING SUPPORT ECU ASSEMBLY (w/ Pre-crash Safety System)


C292380
3.406,0.135 3.823,0.469 0.417,0.333 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a 3.5,0.208 3.813,0.406 0.313,0.198 10 false F84
*a Component without harness connected
(Driving Support ECU assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F84 driving support ECU assembly connector.

C292381
1.208,0.208 1.635,0.469 0.427,0.26 5.135,0.104 5.542,0.333 0.406,0.229 5.958,1.135 6.229,1.5 6.229,1.5 6.365,1.5 true 1.802,1.177 1.438,1.635 1.438,1.635 1.302,1.635 true 2.938,1.188 3.135,1.646 3.135,1.646 3.219,1.646 true 3.042,1.188 3.344,1.396 3.344,1.396 3.469,1.396 true 3.063,1.052 3.396,0.927 3.396,0.927 3.49,0.927 true 2.969,1.052 3.229,0.479 3.229,0.479 3.323,0.479 true 0.542,0.115 0.854,0.313 0.313,0.198 10 false *a 1.302,0.25 1.615,0.448 0.313,0.198 10 false F84 3.781,0.125 4.094,0.323 0.313,0.198 10 false *1 5.219,0.125 5.531,0.323 0.313,0.198 10 false F25 6.448,1.406 6.906,1.604 0.458,0.198 10 false BAT 0.948,1.542 1.406,1.74 0.458,0.198 10 false GND 3.281,1.563 3.896,1.76 0.615,0.198 10 false CA2H 3.542,1.302 4.156,1.5 0.615,0.198 10 false CA1P 3.563,0.833 4.177,1.031 0.615,0.198 10 false CA1N 3.406,0.375 4.021,0.573 0.615,0.198 10 false CA2L
*1 DLC3 - -
*a Front view of wire harness connector
(to Driving Support ECU Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Sub Bus 2 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F84-39 (CA2H) - F84-17 (CA2L) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F84-39 (CA2H) - F84-25 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F84-17 (CA2L) - F84-25 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F84-39 (CA2H) - F25-16 (BAT) G - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F84-17 (CA2L) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Sub Bus 13 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F84-40 (CA1P) - F84-18 (CA1N) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
F84-40 (CA1P) - F84-25 (GND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F84-18 (CA1N) - F84-25 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F84-40 (CA1P) - F25-16 (BAT) R - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F84-18 (CA1N) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-crash Safety System)


C292385
3.375,0.094 3.792,0.354 0.417,0.26 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 3.5,0.125 3.813,0.323 0.313,0.198 10 false A3
*a Component without harness connected
(Millimeter Wave Radar Sensor Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A3 millimeter wave radar sensor assembly connector.

C292386
1.938,0.115 2.385,0.396 0.448,0.281 5.094,0.063 5.542,0.344 0.448,0.281 1.479,1.385 1.594,1.385 1.594,1.385 1.948,0.917 true 1.51,0.552 1.635,0.552 1.635,0.552 2.063,0.906 true 2.156,0.906 2.563,0.552 2.563,0.552 2.688,0.552 true 5.927,1.135 6.146,1.51 6.146,1.51 6.281,1.51 true 1.188,0.125 1.5,0.323 0.313,0.198 10 false *a 3.76,0.104 4.073,0.302 0.313,0.198 10 false *1 2.073,0.167 2.385,0.365 0.313,0.198 10 false A3 1.042,1.302 1.656,1.5 0.615,0.198 10 false SGND 1.104,0.469 1.719,0.667 0.615,0.198 10 false CA1N 2.771,0.469 3.385,0.667 0.615,0.198 10 false CA1P 5.198,0.104 5.51,0.302 0.313,0.198 10 false F25 6.375,1.417 6.833,1.615 0.458,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A3-3 (CA1P) - A3-2 (CA1N) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A3-3 (CA1P)- A3-1 (SGND) R - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A3-2 (CA1N) - A3-1 (SGND) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A3-3 (CA1P) - F25-16 (BAT) R - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A3-2 (CA1N) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




LANE DEPARTURE WARNING CAMERA (w/ Lane Departure Alert System)


C292388
4.594,0.135 4.969,0.417 0.375,0.281 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 4.708,0.177 5.021,0.375 0.313,0.198 10 false S4
*a Component without harness connected
(Lane Departure Warning Camera)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the S4 lane departure warning camera connector.

C292389
1.771,0.083 2.198,0.354 0.427,0.271 5.104,0.063 5.531,0.333 0.427,0.271 5.948,1.167 6.198,1.542 6.198,1.542 6.323,1.542 true 2.281,0.917 2.646,0.49 2.646,0.49 2.76,0.49 true 2.292,1.146 2.573,1.469 2.573,1.469 2.677,1.469 true 2.146,1.146 1.958,1.625 1.958,1.625 1.833,1.625 true 0.677,0.083 0.99,0.281 0.313,0.198 10 false *a 3.51,0.083 3.823,0.281 0.313,0.198 10 false *1 1.896,0.115 2.208,0.313 0.313,0.198 10 false S4 5.198,0.094 5.51,0.292 0.313,0.198 10 false F25 6.396,1.448 6.854,1.646 0.458,0.198 10 false BAT 1.479,1.531 1.938,1.729 0.458,0.198 10 false GND 2.76,1.375 3.375,1.573 0.615,0.198 10 false CA1N 2.833,0.396 3.448,0.594 0.615,0.198 10 false CA1P
*1 DLC3 - -
*a Front view of wire harness connector
(to Lane Departure Warning Camera)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
S4-6 (CA1P) - S4-12 (CA1N) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
S4-6 (CA1P) - S4-11 (GND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
S4-12 (CA1N) - S4-11 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
S4-6 (CA1P) - F25-16 (BAT) R - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
S4-12 (CA1N) - F25-16 (BAT) W - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System)


C294681
2.99,0.198 3.427,0.531 0.438,0.333 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 3.104,0.26 3.563,0.458 0.458,0.198 10 false X13
*a Component without harness connected
(Television Camera Assembly)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the X13 television camera assembly connector.

C295280C02
1.979,0.094 2.375,0.365 0.396,0.271 5.042,0.083 5.438,0.354 0.396,0.271 1.594,1.49 1.719,1.49 1.719,1.49 2.01,1.073 true 1.563,0.344 1.688,0.344 1.688,0.344 2.01,0.844 true 5.146,0.667 4.792,0.271 4.792,0.271 4.656,0.271 true 6.198,1.521 6.083,1.521 6.083,1.521 5.875,1.146 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 2.073,0.135 2.531,0.333 0.458,0.198 10 false X13 1.135,1.406 1.75,1.604 0.615,0.198 10 false CANH 1.125,0.26 1.74,0.458 0.615,0.198 10 false CANL 4.385,0.188 5,0.385 0.615,0.198 10 false CG 5.115,0.125 5.573,0.323 0.458,0.198 10 false F25 6.292,1.438 6.75,1.635 0.458,0.198 10 false BAT
*a Front view of wire harness connector
(to Television Camera Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
X13-4 (CANH) - X13-1 (CANL) L - Y HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
X13-4 (CANH) - F25-4 (CG) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
X13-1 (CANL) - F25-4 (CG) Y - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
X13-4 (CANH) - F25-16 (BAT) L - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
X13-1 (CANL) - F25-16 (BAT) Y - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher