If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly or front No. 2 speaker assembly | A |
| Rear speaker assembly | B |
If sound cannot be heard from any speaker, inspect all of them.
A
B
Disconnect the F69 radio and display receiver assembly connector.
Disconnect the H3 and I3 front No. 1 speaker assembly connectors.
Disconnect the G1 and G5 front No. 2 speaker assembly connectors.
Measure the resistance between each of the front No. 2 speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F69-1 (FR+) - G1-4 (+) | Always | Below 1 Ω |
| F69-5 (FR-) - G1-2 (-) | Always | Below 1 Ω |
| F69-2 (FL+) - G5-4 (+) | Always | Below 1 Ω |
| F69-6 (FL-) - G5-2 (-) | Always | Below 1 Ω |
Measure the resistance between each of the front No. 1 speaker assemblies and the front No. 2 speaker assemblies to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H3-1 - G1-3 (+) | Always | Below 1 Ω |
| H3-2 - G1-1 (-) | Always | Below 1 Ω |
| I3-1 - G5-3 (+) | Always | Below 1 Ω |
| I3-2 - G5-1 (-) | Always | Below 1 Ω |
Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F69-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| F69-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| F69-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| F69-6 (FL-) - Body ground | Always | 10 kΩ or higher |
Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G1-3 (+) - Body ground | Always | 10 kΩ or higher |
| G1-1 (-) - Body ground | Always | 10 kΩ or higher |
| G5-3 (+) - Body ground | Always | 10 kΩ or higher |
| G5-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
| *a | Component without harness connected
(Front No. 1 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
| *a | Component without harness connected
(Front No. 2 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (+) - 2 (-) | Always | 10 kΩ or higher |
| 3 (+) - 4 (+) | Always | Below 1 Ω |
| 1 (-) - 2 (-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that the malfunction disappears when a known good speaker is installed.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Malfunction disappears.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH side.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F70 radio and display receiver assembly connector.
Disconnect the K4 and J4 rear speaker assembly connectors.
Measure the resistance between each of the rear speaker assemblies and the radio and display receiver assembly to check for an open circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F70-1 (RR+) - J4-1 | Always | Below 1 Ω |
| F70-3 (RR-) - J4-2 | Always | Below 1 Ω |
| F70-2 (RL+) - K4-1 | Always | Below 1 Ω |
| F70-6 (RL-) - K4-2 | Always | Below 1 Ω |
Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F70-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| F70-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| F70-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| F70-6 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
| *a | Component without harness connected
(Rear Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG