Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2013.12–2016.11
RM3160E _56 Audio / Visual / Telematics _019700 AUDIO / VIDEO _0096790 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.

WIRING DIAGRAM

E268499
0.833,0.802 1.333,0.969 0.5,0.167 10 false MACC 0.844,1.271 1.344,1.438 0.5,0.167 10 false MCO+ 0.865,1.75 1.365,1.917 0.5,0.167 10 false MCO- 0.865,2.698 1.281,2.865 0.417,0.167 10 false SNS2 0.167,3.156 0.646,3.385 0.479,0.229 10 false S1 0.167,3.323 2.167,3.74 2,0.417 10 false Map Light Assembly (Telephone Microphone Assembly) 3.281,2.083 4.052,2.292 0.771,0.208 10 false (Shielded) 5.927,0.802 6.427,0.969 0.5,0.167 10 false MACC 5.927,1.271 6.344,1.438 0.417,0.167 10 false MIN+ 5.927,1.75 6.26,1.917 0.333,0.167 10 false MIN- 5.927,2.229 6.427,2.396 0.5,0.167 10 false SGND 5.927,2.698 6.344,2.865 0.417,0.167 10 false SNS2 5.438,3.156 6.031,3.469 0.594,0.313 10 false F71 5.438,3.323 7.135,3.74 1.698,0.417 10 false Radio and Display Receiver Assembly 1.333,0.698 1.583,0.875 0.25,0.177 10 false 3 1.333,1.167 1.615,1.344 0.281,0.177 10 false 2 1.333,1.646 1.615,1.823 0.281,0.177 10 false 4 1.333,2.594 1.5,2.76 0.167,0.167 10 false 13 5.74,0.698 5.906,0.865 0.167,0.167 10 false 4 5.74,1.167 5.906,1.333 0.167,0.167 10 false 5 5.74,2.594 5.906,2.76 0.167,0.167 10 false 6 5.667,1.646 5.917,1.813 0.25,0.167 10 false 19 5.667,2.125 5.917,2.292 0.25,0.167 10 false 18

PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E277821

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F71 radio and display receiver assembly connector.


b.

Disconnect the S1 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-6 (SNS2) - S1-13 (SNS2) Always Below 1 Ω
F71-4 (MACC) - S1-3 (MACC) Always Below 1 Ω
F71-5 (MIN+) - S1-2 (MCO+) Always Below 1 Ω
F71-19 (MIN-) - S1-4 (MCO-) Always Below 1 Ω
F71-6 (SNS2) - Body ground Always 10 kΩ or higher
F71-4 (MACC) - Body ground Always 10 kΩ or higher
F71-5 (MIN+) - Body ground Always 10 kΩ or higher
F71-19 (MIN-) - Body ground Always 10 kΩ or higher
F71-18 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the F71 radio and display receiver assembly connector.


b.

Reconnect the S1 map light assembly (telephone microphone assembly) connector.


c.
E176671C63
1.479,0.542 1.969,0.833 0.49,0.292 2.229,2.01 2.896,2.698 false 2.229,1.74 2.854,1.302 false 2.052,2.01 1.385,2.698 false 1.604,0.594 2.188,0.979 0.583,0.385 10 false F71 0.24,0.177 0.615,0.542 0.375,0.365 10 false *a 2.75,2.708 3.26,3 0.51,0.292 10 false SGND 2.875,1.198 3.427,1.594 0.552,0.396 10 false MACC 1.167,2.708 1.688,2.979 0.521,0.271 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F71-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-18 (SGND) - Body ground Always Below 1 Ω
F71-19 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E287094C01
2.656,1.781 2.208,1.417 false 2.406,0.656 1.99,1.198 false 0.188,0.146 0.5,0.302 0.313,0.156 10 false *a 2.708,1.698 3.24,1.948 0.531,0.25 10 false SNS2 2.5,0.563 3.031,0.813 0.531,0.25 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (SNS2) - 4 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the F71 radio and display receiver assembly connector.


b.

Reconnect the S1 map light assembly (telephone microphone assembly) connector.


c.

Turn the ignition switch to ACC.


d.
E287103C01
1.583,0.167 1.885,0.365 0.302,0.198 2.083,1.177 2.667,0.75 false 1.896,1.271 2.333,1.833 false 0.167,0.167 0.333,0.333 0.167,0.167 10 false *a 1.646,0.167 1.896,0.333 0.25,0.167 10 false S1 2.667,0.563 3.167,0.729 0.5,0.167 10 false MCO+ 2.333,1.844 2.833,2.01 0.5,0.167 10 false MCO-
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 2 (MCO+) and 4 (MCO-) of the S1 map light assembly (telephone microphone assembly) connector.


e.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. B




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)