This DTC is stored when a malfunction occurs in the speakers.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C3 | Speaker Output Short | A short is detected in the speaker output circuit | ·
Harness or connector ·
Speaker ·
Radio and display receiver assembly |
Disconnect the F69 and F70 radio and display receiver assembly connectors.
Disconnect the G1 and G5 front No. 2 speaker assembly connectors.
Disconnect the K4 and J4 rear speaker assembly connectors.
Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F69-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| F69-5 (FR-) - Body ground | Always | 10 kΩ or higher |
| F69-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| F69-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| F70-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| F70-3 (RR-) - Body ground | Always | 10 kΩ or higher |
| F70-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| F70-6 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H3 and I3 front No. 1 speaker assembly connectors.
Disconnect the G1 and G5 front No. 2 speaker assembly connectors.
Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G1-3 (+) - Body ground | Always | 10 kΩ or higher |
| G1-1 (-) - Body ground | Always | 10 kΩ or higher |
| G5-3 (+) - Body ground | Always | 10 kΩ or higher |
| G5-1 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
| *a | Component without harness connected
(Front No. 1 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
| *a | Component without harness connected
(Front No. 2 Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (+) - 2 (-) | Always | 10 kΩ or higher |
| 3 (+) - 4 (+) | Always | Below 1 Ω |
| 1 (-) - 2 (-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front No. 2 speaker assembly is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH side.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
| *a | Component without harness connected
(Rear Speaker Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG