Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2013.12–2016.11
RM3160E _56 Audio / Visual / Telematics _019700 AUDIO / VIDEO _0096790 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the radio and display receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the radio and display receiver assembly cannot be operated using the steering pad switch assembly, and the radio and display receiver assembly itself will not function.

WIRING DIAGRAM

E287096E03
0.396,1.167 1.167,1.365 0.771,0.198 10 false Voice 1.021,1.177 1.792,1.375 0.771,0.198 10 false Off Hook 1.802,1.188 2.573,1.385 0.771,0.198 10 false On Hook 2.656,1.115 3.146,1.656 0.49,0.542 10 false MODE/ HOLD 0.24,2.135 1.01,2.333 0.771,0.198 10 false Volume- 1.031,2.135 1.802,2.333 0.771,0.198 10 false Volume+ 1.979,2.135 2.75,2.333 0.771,0.198 10 false Seek- 2.75,2.135 3.521,2.333 0.771,0.198 10 false Seek+ 2.01,3.385 2.781,3.583 0.771,0.198 10 false Down 2.948,3.396 3.719,3.594 0.771,0.198 10 false Up 0.521,4.677 1.292,4.875 0.771,0.198 10 false Left 1.25,4.677 2.021,4.875 0.771,0.198 10 false Right 2.021,4.688 2.792,4.885 0.771,0.198 10 false Back 2.781,4.688 3.552,4.885 0.771,0.198 10 false Enter 1.125,5.646 4.646,5.906 3.521,0.26 10 false Steering Pad Switch Assembly 4.688,4.344 5.76,5.021 1.073,0.677 10 false Spiral Cable Sub-assembly 5.979,4.5 7.115,5.188 1.135,0.688 10 false Radio and Display Receiver Assembly 4.552,0.719 4.865,0.917 0.313,0.198 10 false z4 4.563,1.667 4.875,1.865 0.313,0.198 10 false z4 4.552,2.615 4.865,2.813 0.313,0.198 10 false z4 4.552,3.885 4.865,4.083 0.313,0.198 10 false z4 5.531,0.719 5.844,0.917 0.313,0.198 10 false F61 5.531,1.667 5.844,1.865 0.313,0.198 10 false F61 5.542,2.615 5.854,2.813 0.313,0.198 10 false F61 5.531,3.885 5.844,4.083 0.313,0.198 10 false F61 4.552,0.521 4.865,0.719 0.313,0.198 10 false 10 4.604,1.469 4.917,1.667 0.313,0.198 10 false 8 4.552,2.417 4.865,2.615 0.313,0.198 10 false 11 4.594,3.698 4.906,3.896 0.313,0.198 10 false 9 5.615,0.51 5.927,0.708 0.313,0.198 10 false 5 5.615,1.469 5.927,1.667 0.313,0.198 10 false 3 5.615,2.417 5.927,2.615 0.313,0.198 10 false 6 5.615,3.688 5.927,3.885 0.313,0.198 10 false 4 5,0.604 5.469,0.854 0.469,0.25 10 false AU2 5,1.542 5.469,1.792 0.469,0.25 10 false EAU 4.99,2.5 5.458,2.75 0.469,0.25 10 false AU1 5.01,3.771 5.479,4.021 0.469,0.25 10 false AU3 6.01,0.615 6.323,0.813 0.313,0.198 10 false 22 6.021,1.552 6.333,1.75 0.313,0.198 10 false 23 6.01,2.49 6.323,2.688 0.313,0.198 10 false 21 6.01,3.76 6.323,3.958 0.313,0.198 10 false 24 6.271,0.729 6.76,0.958 0.49,0.229 10 false SW2 6.281,1.677 6.771,1.906 0.49,0.229 10 false SWG 6.281,2.625 6.771,2.854 0.49,0.229 10 false SW1 6.281,3.896 6.771,4.125 0.49,0.229 10 false SW3 5.979,4.333 6.469,4.563 0.49,0.229 10 false F71

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STEERING PAD SWITCH SIGNAL)
a.

Disconnect the F71 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-21 (SW1) - F71-23 (SWG) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 313 to 345 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume- switch pushed 2955 to 3265 Ω
Up switch pushed Below 2.5 Ω
Down switch pushed 313 to 345 Ω
F71-22 (SW2) - F71-23 (SWG) No switch pushed 95 to 105 kΩ
MODE/HOLD switch pushed Below 2.5 Ω
On hook switch pushed 313 to 345 Ω
Off hook switch pushed 950 to 1050 Ω
Voice switch pushed 2955 to 3265 Ω
F71-24 (SW3) - F71-23 (SWG) No switch pushed 95 to 105 kΩ
Enter switch pushed Below 2.5 Ω
Back switch pushed 313 to 345 Ω
Right switch pushed 950 to 1050 Ω
Left switch pushed 2955 to 3265 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

E284080C02
4.75,0.594 4.958,0.74 false 4.656,0.604 4.76,0.823 false 4.583,0.604 4.521,0.917 false 4.5,0.604 4.313,0.781 false 4.729,1.344 4.771,1.875 false 5.031,1.281 4.927,1.719 false 5.406,1.354 4.927,1.885 false 5.292,1.781 5.583,1.781 false 5.094,1.896 5.583,2.146 false 4.927,2.073 4.927,2.74 false 2.469,1.229 2.292,1.75 false 2.052,1.177 2.104,1.719 false 1.625,1.385 1.875,1.75 false 1.854,2.01 1.552,2.104 false 2.042,2.073 1.5,2.313 false 1.979,2.365 1.792,2.625 false 2.188,2.375 2.094,2.698 false 2.333,2.083 2.333,2.875 false 0.292,0.25 0.604,0.406 0.313,0.156 10 false *a 1.448,1.229 1.677,1.396 0.229,0.167 10 false *b 1.396,2.031 1.708,2.188 0.313,0.156 10 false *c 1.969,1.01 2.177,1.229 0.208,0.219 10 false *d 1.323,2.25 1.635,2.406 0.313,0.156 10 false *e 2.469,1.031 2.781,1.188 0.313,0.156 10 false *f 1.646,2.615 1.979,2.865 0.333,0.25 10 false *g 1.99,2.719 2.302,2.875 0.313,0.156 10 false *h 2.271,2.948 2.583,3.104 0.313,0.156 10 false *i 5,1.073 5.25,1.292 0.25,0.219 10 false *j 4.865,2.802 5.177,2.958 0.313,0.156 10 false *k 4.646,1.177 4.958,1.333 0.313,0.156 10 false *l 5.615,2.156 5.927,2.313 0.313,0.156 10 false *m 5.375,1.188 5.688,1.344 0.313,0.156 10 false *n 5.635,1.688 5.948,1.844 0.313,0.156 10 false *o 5,0.74 5.448,0.906 0.448,0.167 10 false AU1 4.708,0.854 5.156,1.021 0.448,0.167 10 false AU2 4.375,0.969 4.823,1.135 0.448,0.167 10 false AU3 4.073,0.813 4.521,0.979 0.448,0.167 10 false EAU
*a Component without harness connected
(Steering Pad Switch Assembly)
*b Volume+
*c Volume- *d Seek+
*e Seek- *f MODE/HOLD
*g Off hook *h On hook
*i Voice *j Up
*k Down *l Left
*m Right *n Enter
*o Back - -


Standard Resistance:
Tester Connection Condition Specified Condition
11 (AU1) - 8 (EAU) No switch pushed 95 to 105 kΩ
Seek+ switch pushed Below 2.5 Ω
Seek- switch pushed 313 to 345 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume- switch pushed 2955 to 3265 Ω
Up switch pushed Below 2.5 Ω
Down switch pushed 313 to 345 Ω
10 (AU2) - 8 (EAU) No switch pushed 95 to 105 kΩ
MODE/HOLD switch pushed Below 2.5 Ω
On hook switch pushed 313 to 345 Ω
Off hook switch pushed 950 to 1050 Ω
Voice switch pushed 2955 to 3265 Ω
9 (AU3) - 8 (EAU) No switch pushed 95 to 105 kΩ
Enter switch pushed Below 2.5 Ω
Back switch pushed 313 to 345 Ω
Right switch pushed 950 to 1050 Ω
Left switch pushed 2955 to 3265 Ω



Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.
E268445C20
1.583,0.292 1.906,0.49 0.323,0.198 0.865,3.875 1.188,4.073 0.323,0.198 1.229,1.167 1.583,1.031 false 1.698,1.031 1.24,0.635 false 2.25,1.188 1.896,1.021 false 2.417,3.729 1.854,3.969 false 1.656,3.99 1.729,3.583 false 1.552,3.99 1.333,3.573 false 2.281,0.552 1.833,0.99 false 2.063,3.635 1.771,3.969 false 0.135,0.115 0.448,0.313 0.313,0.198 10 false *a 0.75,0.219 1.063,0.417 0.313,0.198 10 false *b 1.677,0.302 1.99,0.5 0.313,0.198 10 false z4 0.958,1.125 1.292,1.323 0.333,0.198 10 false AU1 0.958,0.5 1.292,0.698 0.333,0.198 10 false AU2 2.292,1.135 2.625,1.333 0.333,0.198 10 false EAU 0.74,3.313 1.052,3.51 0.313,0.198 10 false *c 0.927,3.896 1.24,4.094 0.313,0.198 10 false F61 2.479,3.656 2.813,3.854 0.333,0.198 10 false EAU 1.583,3.417 1.917,3.615 0.333,0.198 10 false AU2 1.094,3.406 1.427,3.604 0.333,0.198 10 false AU1 2.354,0.479 2.688,0.677 0.333,0.198 10 false AU3 2.01,3.417 2.344,3.615 0.333,0.198 10 false AU3
*a Component without harness connected
(Spiral Cable Sub-assembly)
*b Steering Pad Switch Assembly Side
*c Vehicle Side


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z4-8 (EAU) - F61-3 (EAU) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right
z4-11 (AU1) - F61-6 (AU1) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right
z4-10 (AU2) - F61-5 (AU2) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right
z4-9 (AU3) - F61-4 (AU3) Center 3 Ω or less
2.5 rotations to the left
2.5 rotations to the right



c.

After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z4-8 (EAU) - F61-3 (EAU) Always 3 Ω or less
z4-11 (AU1) - F61-6 (AU1) Always 3 Ω or less
z4-10 (AU2) - F61-5 (AU2) Always 3 Ω or less
z4-9 (AU3) - F61-4 (AU3) Always 3 Ω or less


NOTICE:
·

Press and hold the lock located in the center of the spiral cable sub-assembly to rotate the spiral cable sub-assembly.

·

The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying.

·

As the spiral cable sub-assembly may break, do not rotate the spiral cable sub-assembly more than the specified amount.




Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY