When an open or short circuit is detected in the antenna coil built into the transponder key coil, the transponder key ECU assembly stores this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2784 | Antenna Coil Open / Short | The antenna coil in the transponder key coil is open/shorted. | ·
Wire harness or connector ·
Transponder key coil ·
Transponder key ECU assembly |
DTC Output Confirmation Operation:
Insert the door control transmitter assembly into the ignition key cylinder. |
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Engine cannot be started | - |
| DTC No. | Data List and Active Test |
|---|---|
| B2784 | Antenna Coil Status |
If the transponder key ECU assembly is replaced, refer to Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Perform "DTC Output Confirmation Operation" procedure.
Check for DTCs.
DTC B2784 is not output.
| Result | Proceed to |
|---|---|
| B2784 is not output | A |
| B2784 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Check that the connector is properly connected to the transponder key coil.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Perform "DTC Output Confirmation Operation" procedure.
Check for DTCs.
DTC B2784 is not output.
| Result | Proceed to |
|---|---|
| B2784 is not output | A |
| B2784 is output | B |
A
B
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Transponder Key Coil) |
*b | Waveform 1 |
| *c | Waveform 2 | - | - |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F53-1 (ANT1) - Body ground | Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder | 2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| F53-5 (ANT2) - Body ground | Within 3 seconds of inserting door control transmitter assembly into ignition key cylinder | 2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 2) |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the transponder key ECU assembly with a new one.
Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to Service Bulletin.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Perform "DTC Output Confirmation Operation" procedure.
Check for DTCs.
DTC B2784 is not output.
| Result | Proceed to |
|---|---|
| B2784 is not output | A |
| B2784 is output | B |
A
B
Disconnect the F66 transponder key ECU assembly connector.
Disconnect the F53 transponder key coil connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F66-4 (ANT1) - F53-1 (ANT1) | Always | Below 1 Ω |
| F66-15 (ANT2) - F53-5 (ANT2) | Always | Below 1 Ω |
| F66-4 (ANT1) or F53-1 (ANT1) - Body ground | Always | 10 kΩ or higher |
| F66-15 (ANT2) or F53-5 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG