DTC B2793 is stored when a malfunction is found in the door control transmitter assembly during key ID code registration or a key ID code is not registered normally. Replace the door control transmitter assembly if key ID code registration cannot be performed normally and this DTC is output.
DTC B2794 is stored when a door control transmitter assembly with an incomplete key ID code is inserted into the ignition key cylinder.
DTC B2797 is stored when a door control transmitter assembly with a BCC malfunction is inserted into the ignition key cylinder.
DTC B2798 is stored when a door control transmitter assembly is inserted into the ignition key cylinder but a communication error occurs between the door control transmitter assembly and transponder key ECU assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2793 | Transponder Chip Malfunction | A transponder chip malfunction (1 trip detection logic*). | ·
Door control transmitter assembly ·
Transponder key coil ·
Transponder key ECU assembly |
DTC Output Confirmation Operation:
Insert the door control transmitter assembly into the ignition key cylinder. |
| B2794 | Unmatched Encryption Code | A door control transmitter assembly with an incomplete key ID code is inserted into the ignition key cylinder (1 trip detection logic*). | ·
Door control transmitter assembly ·
Transponder key coil ·
Transponder key ECU assembly |
DTC Output Confirmation Operation:
Insert the door control transmitter assembly into the ignition key cylinder. |
| B2797 | Communication Malfunction No. 1 | A door control transmitter assembly with a BCC malfunction is inserted into the ignition key cylinder (1 trip detection logic*). | ·
Door control transmitter assembly ·
Transponder key coil ·
Transponder key ECU assembly |
DTC Output Confirmation Operation:
Insert the door control transmitter assembly into the ignition key cylinder. |
| B2798 | Communication Malfunction No. 2 | Key ID code identification cannot be completed within the specified time (1 trip detection logic*). | ·
Door control transmitter assembly ·
Transponder key coil ·
Transponder key ECU assembly |
DTC Output Confirmation Operation:
Insert the door control transmitter assembly into the ignition key cylinder. |
*: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Engine cannot be started | - |
| DTC No. | Data List and Active Test |
|---|---|
| B2793 | - |
| B2794 | - |
| B2797 | - |
| B2798 | - |
If the transponder key ECU assembly or a door control transmitter assembly is replaced, refer to Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Perform "DTC Output Confirmation Operation" procedure.
Check for DTCs.
If DTC B2793, B2794, B2797, or B2798 is stored, clear the DTCs before checking the next door control transmitter assembly.
DTC B2793, B2974, B2797 and B2798 are not output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output for all of the door control transmitter assemblies | B |
| DTCs are output for any of the door control transmitter assemblies | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Check that the connector is properly connected to the transponder key coil.
Check that the engine starts with the door control transmitter assembly.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Replace the transponder key coil.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>TRANSPONDER KEY AMPLIFIER>REMOVAL
Check that the engine starts with the door control transmitter assembly.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG