Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › 2013.12–2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0097257 REAR VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the radio and display receiver assembly judges that the signals or signal lines between the radio and display receiver assembly and the television camera assembly are not normal as a result of its self check.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Back Camera Disconnected Open or short in the television camera assembly signal circuit
·

Harness or connector

·

Television camera assembly

·

Radio and display receiver assembly



WIRING DIAGRAM

E267063
2.313,0.531 2.635,0.74 0.323,0.208 10 false 11 2.271,1.115 2.729,1.313 0.458,0.198 10 false F72 2.271,1.51 2.729,1.708 0.458,0.198 10 false F72 2.281,1.896 2.74,2.094 0.458,0.198 10 false F72 2.271,2.302 2.542,2.51 0.271,0.208 10 false F69 1.854,0.708 2.313,0.906 0.458,0.198 10 false CA+ 1.938,1.094 2.396,1.292 0.458,0.198 10 false V+ 1.948,1.5 2.406,1.698 0.458,0.198 10 false V- 1.729,1.896 2.25,2.115 0.521,0.219 10 false CGND 1.75,2.302 2.271,2.521 0.521,0.219 10 false GND1 2.313,0.938 2.635,1.146 0.323,0.208 10 false 12 2.313,1.323 2.635,1.531 0.323,0.208 10 false 24 2.313,1.719 2.635,1.927 0.323,0.208 10 false 23 2.281,0.719 2.74,0.917 0.458,0.198 10 false F72 2.344,2.115 2.667,2.323 0.323,0.208 10 false 7 4.844,0.625 5.167,0.833 0.323,0.208 10 false 6 4.844,1.021 5.167,1.229 0.323,0.208 10 false 3 4.844,1.417 5.146,1.635 0.302,0.219 10 false 2 4.844,1.813 5.167,2.021 0.323,0.208 10 false 5 5.021,0.708 5.479,0.906 0.458,0.198 10 false CB+ 5.021,1.115 5.479,1.313 0.458,0.198 10 false CV+ 5.031,1.51 5.5,1.75 0.469,0.24 10 false CV- 5.021,1.896 5.542,2.115 0.521,0.219 10 false CGND 4.729,2.229 5.188,2.427 0.458,0.198 10 false X12 4.719,2.396 6.635,2.802 1.917,0.406 10 false Television Camera Assembly 3.479,1.74 3.792,1.938 0.313,0.198 10 false *1 0.729,2.667 2.427,3 1.698,0.333 10 false Radio and Display Receiver Assembly 0.344,3.354 1.469,3.583 1.125,0.229 10 false *1: Shielded

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the F72 radio and display receiver assembly connector.


b.

Disconnect the X12 television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F72-11 (CA+) - X12-6 (CB+) Always Below 1 Ω
F72-12 (V+) - X12-3 (CV+) Always Below 1 Ω
F72-24 (V-) - X12-2 (CV-) Always Below 1 Ω
F72-23 (CGND) - X12-5 (CGND) Always Below 1 Ω
F72-11 (CA+) - Body ground Always 10 kΩ or higher
F72-12 (V+) - Body ground Always 10 kΩ or higher
F72-24 (V-) - Body ground Always 10 kΩ or higher
F72-23 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the F72 radio and display receiver assembly connector.


b.
E271917C21
1.521,0.188 1.969,0.479 0.448,0.292 1.302,1.813 1.229,1.313 false 0.74,1.833 1.104,1.313 false 0.813,0.771 1.229,1.125 false 1.635,0.25 1.948,0.448 0.313,0.198 10 false F72 0.573,1.813 0.885,2.01 0.313,0.198 10 false V- 1.146,1.823 1.771,2.052 0.625,0.229 10 false CGND 0.5,0.646 1.125,0.875 0.625,0.229 10 false CA+ 0.115,0.073 0.74,0.302 0.625,0.229 10 false *a
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F72-24 (V-) - Body ground Always Below 1 Ω
F72-23 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F72-11 (CA+) - F72-23 (CGND) Ignition switch ACC 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

3.INSPECT TELEVISION CAMERA ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

3.INSPECT TELEVISION CAMERA ASSEMBLY
a.

Reconnect the X12 television camera assembly connector.


b.
E279721C11
1.479,0.208 1.896,0.5 0.417,0.292 1.479,2.396 1.927,2.677 0.448,0.281 0.729,0.823 1.115,1.198 false 1.854,3.698 2.5,4.188 false 0.094,0.083 0.438,0.25 0.344,0.167 10 false *a 2.521,4.219 2.948,4.396 0.427,0.177 10 false GND1 1.573,0.271 1.917,0.438 0.344,0.167 10 false F72 1.604,2.469 1.948,2.635 0.344,0.167 10 false F69 0.51,0.688 0.854,0.854 0.344,0.167 10 false V+
*a Component with harness connected
(Radio and Display Receiver Assembly)


E265840C01
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Using an oscilloscope, check the waveform of the television camera assembly.

HINT:

A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


OK:

Waveform is similar to that shown in the illustration.


Item Content
Measurement terminal F72-12 (V+) - F69-7 (GND1)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Ignition switch ON, shift lever in R

HINT:
·

The video waveform changes according to the image sent by the television camera assembly.

·

The video waveform is constantly output when the ignition switch is ACC.




Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG