Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2013.12–2016.11
RM3160E _59 Vehicle Exterior _019721 WIPER / WASHER _0097860 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Headlight Cleaner Motor and Relay Circuit  


DESCRIPTION

The headlight cleaner control relay controls the headlight cleaner motor and pump assembly.

WIRING DIAGRAM

E289378
0.656,0.813 1.479,1.01 0.823,0.198 10 false from Battery 2.083,1 2.906,1.198 0.823,0.198 10 false H-LP CLN 0.396,1.604 2.667,1.969 2.271,0.365 10 false NO. 1 Engine Room Relay Block and NO. 1 Junction Block Assembly 3.927,0.729 4.156,0.896 0.229,0.167 10 false 2 5.042,0.729 5.271,0.896 0.229,0.167 10 false 1 5.813,0.719 6.042,0.885 0.229,0.167 10 false 6 5.99,0.844 6.219,1.01 0.229,0.167 10 false PB 5.677,1.177 5.948,1.354 0.271,0.177 10 false A41 5.688,1.333 6.792,1.708 1.104,0.375 10 false Headlight Cleaner Control Relay 3.781,1.115 4.052,1.292 0.271,0.177 10 false A42 3.771,1.281 5.25,1.625 1.479,0.344 10 false Headlight Cleaner Motor and Pump Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY - IG CIRCUIT)
a.

Disconnect the A42 headlight cleaner motor and pump assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-2 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT HEADLAMP CLEANER MOTOR AND PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT HEADLAMP CLEANER MOTOR AND PUMP ASSEMBLY
HINT:

This check should be performed with the headlight cleaner motor and pump assembly installed to the washer jar.


a.
E190232
0.113,0.074 0.295,0.234 0.183,0.161 10 *a
*a Component without harness connected
(Headlight Cleaner Motor and Pump Assembly)


Fill the washer jar with washer fluid.


b.

Connect a battery positive (+) lead to terminal 2 of the headlight cleaner motor and pump assembly, and a battery negative (-) lead to terminal 1.


c.

Check that washer fluid flows from the washer jar.

OK:

Washer fluid is pumped from the washer jar.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY)

NG

REPLACE HEADLAMP CLEANER MOTOR AND PUMP ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT CLEANER MOTOR AND PUMP ASSEMBLY - HEADLIGHT CLEANER CONTROL RELAY)
a.

Disconnect the A41 headlight cleaner control relay connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-1 - A41-6 (PB) Always Below 1 Ω
A42-1 or A41-6 (PB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR