Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System) › 2013.12–2016.11
RM3160E _58 Vehicle Interior _019705 DOOR LOCK _0098500 WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System) C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The smart door control receiver assembly is used to receive radio waves related to the entry functions of the electrical key transmitter sub-assembly. The certification ECU (smart key ECU assembly) decodes the requested electrical key transmitter sub-assembly operation by identifying a key code based on the radio waves received via the smart door control receiver assembly. The smart door control receiver assembly receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly) (ex. if a door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU (multiplex network body ECU)).

DTC No. Detection Item DTC Detection Condition Trouble Area
B1242 Wireless Door Lock Tuner Circuit Malfunction
·

Short in RDAM to ground between the certification ECU (smart key ECU assembly) and smart door control receiver assembly.

·

Short in RDAM to ground when RCO (5 V) output from the ECU is off.


·

Wire harness or connector

·

Smart door control receiver assembly

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

B440789E64
0.427,3.063 2.198,3.5 1.771,0.438 10 false Smart Door Control Receiver Assembly 0.417,2.875 1.031,3.229 0.615,0.354 10 false M27 5.302,2.906 7.104,3.479 1.802,0.573 10 false Certification ECU (Smart Key ECU Assembly) 1.188,0.854 1.802,1.208 0.615,0.354 10 false DATA 1.365,1.635 1.979,1.99 0.615,0.354 10 false +5 1.24,2.333 1.854,2.688 0.615,0.354 10 false GND 5.74,0.844 6.354,1.198 0.615,0.354 10 false RDAM 5.75,1.646 6.365,2 0.615,0.354 10 false RCO 5.74,2.333 6.354,2.688 0.615,0.354 10 false E 5.385,2.344 6,2.698 0.615,0.354 10 false F13 5.375,0.854 5.99,1.208 0.615,0.354 10 false F12 5.396,0.646 6.01,1 0.615,0.354 10 false 20 5.406,1.448 6.021,1.802 0.615,0.354 10 false 18 5.417,2.135 6.031,2.49 0.615,0.354 10 false 11 1.625,2.229 2.24,2.583 0.615,0.354 10 false 1 1.635,1.542 2.25,1.896 0.615,0.354 10 false 4 1.656,0.75 2.271,1.104 0.615,0.354 10 false 5 5.375,1.656 5.99,2.01 0.615,0.354 10 false F12

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing or inspecting the smart door control receiver assembly and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the smart door control receiver assembly, entry and wireless function performance may be affected.

·

This DTC is not stored within 10 seconds of the engine switch being turned from on (IG) to off.

·

The wireless door lock control system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the wireless door lock control system after confirming that the communication system is functioning properly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to smart entry and start system (for Entry Function) Precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Disconnect the M27 smart door control receiver assembly connector.


b.

Measure the voltage and resistance and check for pulses according to the value(s) in the table below.

B456735C09
1.656,0.146 2.073,0.385 0.417,0.24 3.302,0.156 3.719,0.396 0.417,0.24 5.052,0.156 5.469,0.396 0.417,0.24 6.135,2.021 5.896,1.344 false 4.073,1.99 3.469,1.333 false 2.99,2.031 3.292,1.333 false 5.167,0.219 5.625,0.417 0.458,0.198 10 false F13 3.427,0.208 3.885,0.406 0.458,0.198 10 false F12 1.75,0.208 2.208,0.406 0.458,0.198 10 false F10 6.115,2.052 6.573,2.25 0.458,0.198 10 false E 3.99,2.042 4.448,2.24 0.458,0.198 10 false RCO 2.875,2.073 3.333,2.271 0.458,0.198 10 false RDAM 0.167,0.125 0.625,0.323 0.458,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -


Standard Voltage:
Tester Connection Condition Specified Condition
F12-20 (RDAM) - F13-11 (E) always 11 to 14 V
F12-18 (RCO) - F13-11 (E) always Below 1 V → 4.5 to 5.5 V pulse generation at regular intervals


Standard Resistance:
Tester Connection Condition Specified Condition
F13-11 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (SMART DOOR CONTROL RECEIVER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (SMART DOOR CONTROL RECEIVER ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the F12 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F12-20 (RDAM) - M27-5 (DATA) Always Below 1 Ω
F12-18 (RCO) - M27-4 (+5) Always Below 1 Ω
M27-1 (GND) - Body ground Always Below 1 Ω
M27-5 (DATA) or F12-20 (RDAM) - Body ground Always 10 kΩ or higher
M27-4 (+5) or F12-18 (RCO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR