Home › Vehicle Interior › DOOR LOCK › BACK DOOR LOCK
RM3160E _58 Vehicle Interior _019705 DOOR LOCK _0098511 BACK DOOR LOCK G

DOOR LOCK  BACK DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69350 1.INSPECT BACK DOOR LOCK ASSEMBLY (w/o Power Back Door)

a.

Check the operation of the door lock motor.

i.
B337032
2.188,4.021 1.969,3.729 true 1.74,4.031 1.74,3.74 true 1.385,4.031 1.563,3.74 true 2.583,1.896 2.896,2.052 0.313,0.156 10 false *a 2.625,0.979 2.938,1.135 0.313,0.156 10 false *b 1.156,3.073 1.469,3.229 0.313,0.156 10 false *c 1.635,4.052 2.021,4.24 0.385,0.188 10 false ACT+ 2.156,4.052 2.531,4.24 0.375,0.188 10 false ACT- 1.271,4.063 1.656,4.25 0.385,0.188 10 false D+
*a Close (Lock)
*b Open (Unlock)
*c Component without harness connected
(Back Door Lock Assembly)


Move the door lock to the close (lock) position.


ii.

Apply battery voltage and check the operation of the door lock motor.

OK:
Battery Connection Result
Battery positive (+) → Terminal 2 (ACT+)
Battery negative (-) → Terminal 1 (ACT-)
Back door lock motor open (unlock) operation


If the result is not as specified, replace the back door lock assembly.



b.

Check the operation of the back door courtesy switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ACT-) - 3 (D+) Closed (Locked) 10 kΩ or higher
1 (ACT-) - 3 (D+) Open (Unlocked) Below 1 Ω


If the result is not as specified, replace the back door lock assembly.



Hide 69350 2.INSPECT BACK DOOR LOCK ASSEMBLY (w/ Power Back Door)

B340482
2.208,1.979 2.208,1.667 2.208,1.667 2.438,1.552 true 2.083,1.865 2.083,1.531 2.083,1.531 2.427,1.438 true 2.01,1.708 2.01,1.375 2.01,1.375 2.427,1.313 true 2.802,1.969 2.802,1.677 2.802,1.677 2.583,1.552 true 2.969,1.573 2.906,1.438 2.906,1.438 2.604,1.438 true 2.958,1.302 2.604,1.302 true 0.479,2.323 0.813,2.323 0.813,2.323 1.01,1.781 true 0.521,1.031 0.802,1.031 0.802,1.031 0.823,1.563 true 1.563,1.021 1.365,1.021 1.365,1.021 1.271,1.563 true 1.823,1.667 2.135,1.865 0.313,0.198 10 M- 1.958,1.823 2.271,2.021 0.313,0.198 10 E 2.031,1.99 2.344,2.188 0.313,0.198 10 OPN 2.667,1.99 2.979,2.188 0.313,0.198 10 CLS 2.885,1.594 3.198,1.792 0.313,0.198 10 CTY 2.979,1.229 3.292,1.427 0.313,0.198 10 M+ 1.594,0.938 1.906,1.094 0.313,0.156 10 *a 0.333,0.948 0.646,1.104 0.313,0.156 10 *b 0.323,2.24 0.635,2.396 0.313,0.156 10 *c 1.979,2.698 2.292,2.854 0.313,0.156 10 *d 1.906,2.896 2.219,3.052 0.313,0.156 10 *e 1.771,3.5 2.083,3.656 0.313,0.156 10 *f 1.5,3.938 1.813,4.115 0.313,0.177 10 *g 0.094,0.063 0.406,0.219 0.313,0.156 10 *h
*a Clockwise
*b Counterclockwise
*c Drive Gear
*d Over-latch
*e Full-latch
*f Half-latch
*g Open-latch
*h Component without harness connected
(Back Door Lock Assembly)


a.

Apply battery voltage to the door lock motor and check the operation of the door lock motor.

OK:
Battery Connection Result
Battery positive (+) → 1 (M+)
Battery negative (-) → 2 (M-)
Latch turns to full-latch position (rotates clockwise)
Battery positive (+) → 2 (M-)
Battery negative (-) → 1 (M+)
Latch turns to open-latch position (rotates counterclockwise)


If the result is not as specified, replace the back door lock assembly.


b.

Check the operation of the latch switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Full-latch Switch):
Tester Connection Condition Specified Condition
5 (CLS) - 4 (E) Over-latch Below 1 Ω
5 (CLS) - 4 (E) Open-latch 10 kΩ or higher
5 (CLS) - 4 (E) Full-latch 10 kΩ or higher
5 (CLS) - 4 (E) Half-latch 10 kΩ or higher


Standard Resistance (Selector Switch):
Tester Connection Condition Specified Condition
6 (OPN) - 4 (E) Open-latch Below 1 Ω
6 (OPN) - 4 (E) Half-latch 10 kΩ or higher
6 (OPN) - 4 (E) Full-latch 10 kΩ or higher
6 (OPN) - 4 (E) Over-latch 10 kΩ or higher


Standard Resistance (Back Door Courtesy Light Switch):
Tester Connection Condition Specified Condition
3 (CTY) - 4 (E) Open-latch Below 1 Ω
3 (CTY) - 4 (E) Half-latch 10 kΩ or higher
3 (CTY) - 4 (E) Full-latch 10 kΩ or higher
3 (CTY) - 4 (E) Over-latch 10 kΩ or higher


If the result is not as specified, replace the back door lock assembly.