Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3160E _58 Vehicle Interior _019710 SUPPLEMENTAL RESTRAINT SYSTEMS _0100809 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1622/81  Lost communication with Side Airbag Sensor RH  B1623/81  Side Airbag Sensor Assembly RH Initialization Incomplete  B1632/81  Lost Communication with Rear Airbag Sensor RH  B1633/81  Rear Airbag Sensor Assembly RH Initialization Incomplete  B1642/81  Lost Communication with Side Satellite Sensor Bus RH  


DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat airbag assembly RH and curtain shield airbag assembly RH) consists of the airbag sensor assembly, side airbag sensor assembly RH and rear airbag sensor RH.

The side airbag sensor assembly RH and rear airbag sensor RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1622/81 Lost communication with Side Airbag Sensor RH
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

Rear airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side airbag sensor assembly RH

·

Rear airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode
B1623/81 Side Airbag Sensor Assembly RH Initialization Incomplete
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

Rear airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side airbag sensor assembly RH

·

Rear airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode
B1632/81 Lost Communication with Rear Airbag Sensor RH
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

Rear airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side airbag sensor assembly RH

·

Rear airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode
B1633/81 Rear Airbag Sensor Assembly RH Initialization Incomplete
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

Rear airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side airbag sensor assembly RH

·

Rear airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode
B1642/81 Lost Communication with Side Satellite Sensor Bus RH
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit.

·

Side airbag sensor assembly RH malfunction

·

Rear airbag sensor RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Side airbag sensor assembly RH

·

Rear airbag sensor RH

·

Airbag sensor assembly


Does not apply to test/check mode

WIRING DIAGRAM

C239250E44
0.573,4.677 1.063,4.948 0.49,0.271 10 false L2 5.5,4.698 5.958,5.021 0.458,0.323 10 false L9 3.01,4.844 4.542,5.427 1.531,0.583 10 false Rear Airbag Sensor RH 0.563,4.823 1.813,5.344 1.25,0.521 10 false Side Airbag Sensor Assembly RH 5.479,4.854 7.063,5.229 1.583,0.375 10 false Airbag Sensor Assembly 1.583,0.813 1.875,1.073 0.292,0.26 10 false 4 1.146,0.896 1.656,1.125 0.51,0.229 10 false BBR+ 1.583,1.698 1.813,1.99 0.229,0.292 10 false 3 1.167,1.792 1.625,2.042 0.458,0.25 10 false BBR- 1.583,2.958 1.781,3.26 0.198,0.302 10 false 1 1.146,3.042 1.677,3.302 0.531,0.26 10 false BCR+ 1.594,3.854 1.813,4.219 0.219,0.365 10 false 2 1.177,3.938 1.656,4.208 0.479,0.271 10 false BCR- 2.917,2.958 3.292,3.25 0.375,0.292 10 false 2 3.083,3.063 3.531,3.344 0.448,0.281 10 false BCR+ 2.917,3.844 3.198,4.094 0.281,0.25 10 false 1 3.063,3.958 3.552,4.208 0.49,0.25 10 false BCR- 5.552,0.906 6,1.208 0.448,0.302 10 false BBR+ 5.552,1.802 5.958,2.042 0.406,0.24 10 false BBR- 5.323,0.802 5.604,1.052 0.281,0.25 10 false 17 5.323,1.708 5.594,1.979 0.271,0.271 10 false 18 3.01,4.688 3.396,4.969 0.385,0.281 10 false L12

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CURRENT DTC
a.

Check for current DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then to ON again.

·

Codes other than current DTCs B1622, B1623, B1632, B1633, B1642 and 81 may be output at this time, but they are not related to this check.




Result:
Result Proceed to
Current DTC B1642 or 81 is output. A
Current DTC B1623 is output. B
Current DTC B1632 or B1633 is output. C
Current DTC B1622 is output. D
Current DTCs B1622, B1623, B1632, B1633, B1642 and 81 are not output. E



A

2.CHECK CONNECTORS

B

13.CHECK HISTORY DTC

C

21.CHECK CONNECTORS

D

28.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

E

2.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH and rear airbag sensor RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH and rear airbag sensor RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (OPEN)
a.
C238391C04
0.958,0.469 1.313,0.719 0.354,0.25 0.438,3.552 0.75,3.76 0.313,0.208 1.573,3.688 1.948,4.125 false 1.448,3.677 1.063,4.115 false 1.573,2.427 1.573,1.865 1.573,1.865 1.417,1.865 false 1.635,0.813 1.271,1.052 false 1.76,0.823 2.125,1.052 false 1.708,1.094 1.708,1.271 false 1.052,2.417 1.51,2.76 0.458,0.344 10 false D 1.365,2.417 1.677,2.75 0.313,0.333 10 false C 1.708,2.417 2,2.729 0.292,0.313 10 false B 2.01,2.417 2.302,2.781 0.292,0.365 10 false A 0.688,2.417 1.156,2.75 0.469,0.333 10 false *1 2.5,2.135 2.771,2.479 0.271,0.344 10 false *2 0.635,0.188 0.906,0.438 0.271,0.25 10 false *a 0.354,3.198 0.74,3.531 0.385,0.333 10 false *b 2.01,1.063 2.51,1.302 0.5,0.24 10 false BBR- 1.094,1.063 1.563,1.281 0.469,0.219 10 false BBR+ 1.063,0.51 1.375,0.781 0.313,0.271 10 false L9 0.521,3.573 1.01,3.854 0.49,0.281 10 false L2 1.823,4.125 2.354,4.354 0.531,0.229 10 false BBR+ 0.896,4.125 1.406,4.354 0.51,0.229 10 false BBR- 1.25,1.792 1.781,2.156 0.531,0.365 10 false *3 1.635,1.292 1.865,1.531 0.229,0.24 10 false *4
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-4 (BBR+) - L2-3 (BBR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

4.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT)
a.
C238220C19
0.396,2.26 0.708,2.5 0.313,0.24 1.51,2.448 1.26,2.823 false 1.656,2.448 1.896,2.823 false 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 false D 1.271,0.948 1.677,1.417 0.406,0.469 10 false C 1.729,0.948 2.083,1.375 0.354,0.427 10 false B 2.031,0.958 2.427,1.438 0.396,0.479 10 false A 0.646,0.958 0.938,1.313 0.292,0.354 10 false *1 2.448,0.688 2.833,1.073 0.385,0.385 10 false *2 1.146,0.281 1.51,0.656 0.365,0.375 10 false *3 0.333,1.75 0.667,2.115 0.333,0.365 10 false *a 0.49,2.302 0.948,2.625 0.458,0.323 10 false L2 1.083,2.844 1.698,3.177 0.615,0.333 10 false BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 false BBR+
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-4 (BBR+) - L2-3 (BBR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO B+)
a.
C238220C19
0.396,2.26 0.708,2.5 0.313,0.24 1.51,2.448 1.26,2.823 false 1.656,2.448 1.896,2.823 false 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 false D 1.271,0.948 1.677,1.417 0.406,0.469 10 false C 1.729,0.948 2.083,1.375 0.354,0.427 10 false B 2.031,0.958 2.427,1.438 0.396,0.479 10 false A 0.646,0.958 0.938,1.313 0.292,0.354 10 false *1 2.448,0.688 2.833,1.073 0.385,0.385 10 false *2 1.146,0.281 1.51,0.656 0.365,0.375 10 false *3 0.333,1.75 0.667,2.115 0.333,0.365 10 false *a 0.49,2.302 0.948,2.625 0.458,0.323 10 false L2 1.083,2.844 1.698,3.177 0.615,0.333 10 false BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 false BBR+
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L2-4 (BBR+) - Body ground Ignition switch ON Below 1 V
L2-3 (BBR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

6.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

6.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C238220C19
0.396,2.26 0.708,2.5 0.313,0.24 1.51,2.448 1.26,2.823 false 1.656,2.448 1.896,2.823 false 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 false D 1.271,0.948 1.677,1.417 0.406,0.469 10 false C 1.729,0.948 2.083,1.375 0.354,0.427 10 false B 2.031,0.958 2.427,1.438 0.396,0.479 10 false A 0.646,0.958 0.938,1.313 0.292,0.354 10 false *1 2.448,0.688 2.833,1.073 0.385,0.385 10 false *2 1.146,0.281 1.51,0.656 0.365,0.375 10 false *3 0.333,1.75 0.667,2.115 0.333,0.365 10 false *a 0.49,2.302 0.948,2.625 0.458,0.323 10 false L2 1.083,2.844 1.698,3.177 0.615,0.333 10 false BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 false BBR+
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-4 (BBR+) - Body ground Always 1 MΩ or higher
L2-3 (BBR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

7.CHECK FLOOR WIRE (OPEN)
a.
C256981C07
0.948,0.563 1.26,0.771 0.313,0.208 0.604,3.615 0.917,3.823 0.313,0.208 1.698,2.281 1.698,1.865 1.698,1.865 1.448,1.865 false 1.729,4.125 1.729,4.292 false 1.5,1.042 1.823,0.667 false 2.26,1.063 1.927,0.667 false 1.344,4.073 1.667,3.698 false 2.146,4.063 1.76,3.698 false 0.76,0.177 1.083,0.469 0.323,0.292 10 false *a 2.271,2.26 2.594,2.552 0.323,0.292 10 false A 1.958,2.26 2.281,2.552 0.323,0.292 10 false B 1.365,2.26 1.688,2.552 0.323,0.292 10 false C 1.063,2.26 1.385,2.552 0.323,0.292 10 false D 2.594,2.271 2.917,2.563 0.323,0.292 10 false *2 0.688,2.26 1.01,2.552 0.323,0.292 10 false *1 1.292,1.792 1.615,2.083 0.323,0.292 10 false *3 1.677,4.323 1.927,4.552 0.25,0.229 10 false *4 1.333,1.052 1.823,1.344 0.49,0.292 10 false BCR+ 2.115,1.052 2.604,1.344 0.49,0.292 10 false BCR- 1.156,4.083 1.646,4.375 0.49,0.292 10 false BCR- 2.01,4.063 2.5,4.354 0.49,0.292 10 false BCR+ 1.042,0.594 1.531,0.885 0.49,0.292 10 false L2 0.656,3.635 1.146,3.927 0.49,0.292 10 false L12 0.448,3.188 0.771,3.479 0.323,0.292 10 false *b
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Rear Airbag Sensor RH)


Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-1 (BCR+) - L2-2 (BCR-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

8.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

8.CHECK FLOOR WIRE (SHORT)
a.
C238222C28
1.156,2.302 1.458,2.531 0.302,0.229 2.094,2.448 1.844,2.833 false 2.219,2.438 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 false D 1.458,0.74 1.792,1.208 0.333,0.469 10 false C 1.906,0.74 2.25,1.177 0.344,0.438 10 false B 2.219,0.74 2.49,1.125 0.271,0.385 10 false A 0.813,0.74 1.427,1.208 0.615,0.469 10 false *1 2.469,0.74 2.75,1.073 0.281,0.333 10 false *2 1.396,0.135 1.823,0.542 0.427,0.406 10 false *3 0.99,1.875 1.323,2.229 0.333,0.354 10 false *a 1.24,2.333 1.635,2.677 0.396,0.344 10 false L2 2.344,2.854 2.917,3.073 0.573,0.219 10 false BCR- 1.667,2.854 2.156,3.177 0.49,0.323 10 false BCR+
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-1 (BCR+) - L2-2 (BCR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

9.CHECK FLOOR WIRE (SHORT TO B+)
a.
C238222C28
1.156,2.302 1.458,2.531 0.302,0.229 2.094,2.448 1.844,2.833 false 2.219,2.438 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 false D 1.458,0.74 1.792,1.208 0.333,0.469 10 false C 1.906,0.74 2.25,1.177 0.344,0.438 10 false B 2.219,0.74 2.49,1.125 0.271,0.385 10 false A 0.813,0.74 1.427,1.208 0.615,0.469 10 false *1 2.469,0.74 2.75,1.073 0.281,0.333 10 false *2 1.396,0.135 1.823,0.542 0.427,0.406 10 false *3 0.99,1.875 1.323,2.229 0.333,0.354 10 false *a 1.24,2.333 1.635,2.677 0.396,0.344 10 false L2 2.344,2.854 2.917,3.073 0.573,0.219 10 false BCR- 1.667,2.854 2.156,3.177 0.49,0.323 10 false BCR+
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L2-1 (BCR+) - Body ground Ignition switch ON Below 1 V
L2-2 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

10.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

10.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C238222C28
1.156,2.302 1.458,2.531 0.302,0.229 2.094,2.448 1.844,2.833 false 2.219,2.438 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 false D 1.458,0.74 1.792,1.208 0.333,0.469 10 false C 1.906,0.74 2.25,1.177 0.344,0.438 10 false B 2.219,0.74 2.49,1.125 0.271,0.385 10 false A 0.813,0.74 1.427,1.208 0.615,0.469 10 false *1 2.469,0.74 2.75,1.073 0.281,0.333 10 false *2 1.396,0.135 1.823,0.542 0.427,0.406 10 false *3 0.99,1.875 1.323,2.229 0.333,0.354 10 false *a 1.24,2.333 1.635,2.677 0.396,0.344 10 false L2 2.344,2.854 2.917,3.073 0.573,0.219 10 false BCR- 1.667,2.854 2.156,3.177 0.49,0.323 10 false BCR+
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-1 (BCR+) - Body ground Always 1 MΩ or higher
L2-2 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE FLOOR WIRE

11.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Connect the connectors to the rear airbag sensor RH and airbag sensor assembly.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1642 or 81 is output. A
DTC B1647 or 82 is output. B
DTCs B1642, B1647, 81 and 82 are not output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

12.CHECK REAR AIRBAG SENSOR RH

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

C

12.CHECK REAR AIRBAG SENSOR RH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor Assembly RH


Interchange the rear airbag sensor RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1642 or 81 is output. A
DTC B1647 or 82 is output. B
DTCs B1642, B1647, 81 and 82 are not output. C


g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C

13.CHECK HISTORY DTC
a.

Check for history DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than history DTC B1622 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
History DTC B1622 is not output. A
History DTC B1622 is output. B



A

14.CHECK CONNECTORS

B

20.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
14.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and side airbag sensor assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and side airbag sensor assembly RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

15.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

15.CHECK FLOOR WIRE (OPEN)
a.
C238391C04
0.958,0.469 1.313,0.719 0.354,0.25 0.438,3.552 0.75,3.76 0.313,0.208 1.573,3.688 1.948,4.125 false 1.448,3.677 1.063,4.115 false 1.573,2.427 1.573,1.865 1.573,1.865 1.417,1.865 false 1.635,0.813 1.271,1.052 false 1.76,0.823 2.125,1.052 false 1.708,1.094 1.708,1.271 false 1.052,2.417 1.51,2.76 0.458,0.344 10 false D 1.365,2.417 1.677,2.75 0.313,0.333 10 false C 1.708,2.417 2,2.729 0.292,0.313 10 false B 2.01,2.417 2.302,2.781 0.292,0.365 10 false A 0.688,2.417 1.156,2.75 0.469,0.333 10 false *1 2.5,2.135 2.771,2.479 0.271,0.344 10 false *2 0.635,0.188 0.906,0.438 0.271,0.25 10 false *a 0.354,3.198 0.74,3.531 0.385,0.333 10 false *b 2.01,1.063 2.51,1.302 0.5,0.24 10 false BBR- 1.094,1.063 1.563,1.281 0.469,0.219 10 false BBR+ 1.063,0.51 1.375,0.781 0.313,0.271 10 false L9 0.521,3.573 1.01,3.854 0.49,0.281 10 false L2 1.823,4.125 2.354,4.354 0.531,0.229 10 false BBR+ 0.896,4.125 1.406,4.354 0.51,0.229 10 false BBR- 1.25,1.792 1.781,2.156 0.531,0.365 10 false *3 1.635,1.292 1.865,1.531 0.229,0.24 10 false *4
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-4 (BBR+) - L2-3 (BBR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

16.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

16.CHECK FLOOR WIRE (SHORT)
a.
C238220C19
0.396,2.26 0.708,2.5 0.313,0.24 1.51,2.448 1.26,2.823 false 1.656,2.448 1.896,2.823 false 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 false D 1.271,0.948 1.677,1.417 0.406,0.469 10 false C 1.729,0.948 2.083,1.375 0.354,0.427 10 false B 2.031,0.958 2.427,1.438 0.396,0.479 10 false A 0.646,0.958 0.938,1.313 0.292,0.354 10 false *1 2.448,0.688 2.833,1.073 0.385,0.385 10 false *2 1.146,0.281 1.51,0.656 0.365,0.375 10 false *3 0.333,1.75 0.667,2.115 0.333,0.365 10 false *a 0.49,2.302 0.948,2.625 0.458,0.323 10 false L2 1.083,2.844 1.698,3.177 0.615,0.333 10 false BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 false BBR+
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-4 (BBR+) - L2-3 (BBR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

17.CHECK FLOOR WIRE (SHORT TO B+)
a.
C238220C19
0.396,2.26 0.708,2.5 0.313,0.24 1.51,2.448 1.26,2.823 false 1.656,2.448 1.896,2.823 false 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 false D 1.271,0.948 1.677,1.417 0.406,0.469 10 false C 1.729,0.948 2.083,1.375 0.354,0.427 10 false B 2.031,0.958 2.427,1.438 0.396,0.479 10 false A 0.646,0.958 0.938,1.313 0.292,0.354 10 false *1 2.448,0.688 2.833,1.073 0.385,0.385 10 false *2 1.146,0.281 1.51,0.656 0.365,0.375 10 false *3 0.333,1.75 0.667,2.115 0.333,0.365 10 false *a 0.49,2.302 0.948,2.625 0.458,0.323 10 false L2 1.083,2.844 1.698,3.177 0.615,0.333 10 false BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 false BBR+
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L2-4 (BBR+) - Body ground Ignition switch ON Below 1 V
L2-3 (BBR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

18.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

18.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C238220C19
0.396,2.26 0.708,2.5 0.313,0.24 1.51,2.448 1.26,2.823 false 1.656,2.448 1.896,2.823 false 1.542,0.958 1.542,0.354 1.542,0.354 1.313,0.354 false 0.958,0.958 1.24,1.323 0.281,0.365 10 false D 1.271,0.948 1.677,1.417 0.406,0.469 10 false C 1.729,0.948 2.083,1.375 0.354,0.427 10 false B 2.031,0.958 2.427,1.438 0.396,0.479 10 false A 0.646,0.958 0.938,1.313 0.292,0.354 10 false *1 2.448,0.688 2.833,1.073 0.385,0.385 10 false *2 1.146,0.281 1.51,0.656 0.365,0.375 10 false *3 0.333,1.75 0.667,2.115 0.333,0.365 10 false *a 0.49,2.302 0.948,2.625 0.458,0.323 10 false L2 1.083,2.844 1.698,3.177 0.615,0.333 10 false BBR- 1.75,2.844 2.26,3.094 0.51,0.25 10 false BBR+
*1 Side Airbag Sensor Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-4 (BBR+) - Body ground Always 1 MΩ or higher
L2-3 (BBR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE FLOOR WIRE

19.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Connect the connector to the airbag sensor assembly.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1623 is output. A
DTC B1628 is output. B
DTCs B1623 and B1628 are not output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

C

20.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1622 is output. A
DTC B1627 is output. B
DTCs B1622 and B1627 are not output. C


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

C

21.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side airbag sensor assembly RH and rear airbag sensor RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the side airbag sensor assembly RH and rear airbag sensor RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

22.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

22.CHECK FLOOR WIRE (OPEN)
a.
C256981C07
0.948,0.563 1.26,0.771 0.313,0.208 0.604,3.615 0.917,3.823 0.313,0.208 1.698,2.281 1.698,1.865 1.698,1.865 1.448,1.865 false 1.729,4.125 1.729,4.292 false 1.5,1.042 1.823,0.667 false 2.26,1.063 1.927,0.667 false 1.344,4.073 1.667,3.698 false 2.146,4.063 1.76,3.698 false 0.76,0.177 1.083,0.469 0.323,0.292 10 false *a 2.271,2.26 2.594,2.552 0.323,0.292 10 false A 1.958,2.26 2.281,2.552 0.323,0.292 10 false B 1.365,2.26 1.688,2.552 0.323,0.292 10 false C 1.063,2.26 1.385,2.552 0.323,0.292 10 false D 2.594,2.271 2.917,2.563 0.323,0.292 10 false *2 0.688,2.26 1.01,2.552 0.323,0.292 10 false *1 1.292,1.792 1.615,2.083 0.323,0.292 10 false *3 1.677,4.323 1.927,4.552 0.25,0.229 10 false *4 1.333,1.052 1.823,1.344 0.49,0.292 10 false BCR+ 2.115,1.052 2.604,1.344 0.49,0.292 10 false BCR- 1.156,4.083 1.646,4.375 0.49,0.292 10 false BCR- 2.01,4.063 2.5,4.354 0.49,0.292 10 false BCR+ 1.042,0.594 1.531,0.885 0.49,0.292 10 false L2 0.656,3.635 1.146,3.927 0.49,0.292 10 false L12 0.448,3.188 0.771,3.479 0.323,0.292 10 false *b
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)
*b Front view of wire harness connector
(to Rear Airbag Sensor RH)


Using a service wire, connect terminals 2 (BCR+) and 1 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-1 (BCR+) - L2-2 (BCR-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.


Result:
Proceed to
OK
NG



OK

23.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

23.CHECK FLOOR WIRE (SHORT)
a.
C238222C28
1.156,2.302 1.458,2.531 0.302,0.229 2.094,2.448 1.844,2.833 false 2.219,2.438 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 false D 1.458,0.74 1.792,1.208 0.333,0.469 10 false C 1.906,0.74 2.25,1.177 0.344,0.438 10 false B 2.219,0.74 2.49,1.125 0.271,0.385 10 false A 0.813,0.74 1.427,1.208 0.615,0.469 10 false *1 2.469,0.74 2.75,1.073 0.281,0.333 10 false *2 1.396,0.135 1.823,0.542 0.427,0.406 10 false *3 0.99,1.875 1.323,2.229 0.333,0.354 10 false *a 1.24,2.333 1.635,2.677 0.396,0.344 10 false L2 2.344,2.854 2.917,3.073 0.573,0.219 10 false BCR- 1.667,2.854 2.156,3.177 0.49,0.323 10 false BCR+
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-1 (BCR+) - L2-2 (BCR-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

24.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

24.CHECK FLOOR WIRE (SHORT TO B+)
a.
C238222C28
1.156,2.302 1.458,2.531 0.302,0.229 2.094,2.448 1.844,2.833 false 2.219,2.438 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 false D 1.458,0.74 1.792,1.208 0.333,0.469 10 false C 1.906,0.74 2.25,1.177 0.344,0.438 10 false B 2.219,0.74 2.49,1.125 0.271,0.385 10 false A 0.813,0.74 1.427,1.208 0.615,0.469 10 false *1 2.469,0.74 2.75,1.073 0.281,0.333 10 false *2 1.396,0.135 1.823,0.542 0.427,0.406 10 false *3 0.99,1.875 1.323,2.229 0.333,0.354 10 false *a 1.24,2.333 1.635,2.677 0.396,0.344 10 false L2 2.344,2.854 2.917,3.073 0.573,0.219 10 false BCR- 1.667,2.854 2.156,3.177 0.49,0.323 10 false BCR+
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L2-1 (BCR+) - Body ground Ignition switch ON Below 1 V
L2-2 (BCR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

25.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

25.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C238222C28
1.156,2.302 1.458,2.531 0.302,0.229 2.094,2.448 1.844,2.833 false 2.219,2.438 2.469,2.823 false 1.74,0.74 1.74,0.208 1.74,0.208 1.573,0.208 false 1.146,0.74 1.521,1.229 0.375,0.49 10 false D 1.458,0.74 1.792,1.208 0.333,0.469 10 false C 1.906,0.74 2.25,1.177 0.344,0.438 10 false B 2.219,0.74 2.49,1.125 0.271,0.385 10 false A 0.813,0.74 1.427,1.208 0.615,0.469 10 false *1 2.469,0.74 2.75,1.073 0.281,0.333 10 false *2 1.396,0.135 1.823,0.542 0.427,0.406 10 false *3 0.99,1.875 1.323,2.229 0.333,0.354 10 false *a 1.24,2.333 1.635,2.677 0.396,0.344 10 false L2 2.344,2.854 2.917,3.073 0.573,0.219 10 false BCR- 1.667,2.854 2.156,3.177 0.49,0.323 10 false BCR+
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor Assembly RH
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-1 (BCR+) - Body ground Always 1 MΩ or higher
L2-2 (BCR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

26.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH

NG

REPLACE FLOOR WIRE

26.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Connect the connector to the rear airbag sensor RH.


b.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.


d.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1632 or B1633 is output. A
DTC B1637 or B1638 is output. B
DTCs B1632, B1633, B1637 and B1638 are not output. C


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

27.CHECK REAR AIRBAG SENSOR RH

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

C

27.CHECK REAR AIRBAG SENSOR RH
a.
C238223C02
0.969,1 1.313,1.469 0.344,0.469 10 false *1 2.271,1.01 2.51,1.375 0.24,0.365 10 false *2 2.042,1.01 2.323,1.375 0.281,0.365 10 false A 1.885,1.01 2.135,1.406 0.25,0.396 10 false B 1.438,1.01 1.802,1.448 0.365,0.438 10 false C 1.281,1.01 1.542,1.417 0.26,0.406 10 false D
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor Assembly RH


Interchange the rear airbag sensor RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1632 or B1633 is output. A
DTC B1637 or B1638 is output. B
DTCs B1632, B1633, B1637 and B1638 are not output. C


g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors.



A

B

C

28.CHECK SIDE AIRBAG SENSOR ASSEMBLY RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Side Airbag Sensor Assembly LH
*2 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor assembly RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



Result:
Result Proceed to
DTC B1622 is output. A
DTC B1627 is output. B
DTCs B1622 and B1627 are not output. C


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.



A

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

C