Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3160E _58 Vehicle Interior _019710 SUPPLEMENTAL RESTRAINT SYSTEMS _0100809 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1653/35  Seat Position Airbag Sensor Circuit Malfunction  


DESCRIPTION

The seat position airbag sensor circuit consists of the airbag sensor assembly and seat position airbag sensor.

DTC B1653/35 is stored when a malfunction is detected in the seat position airbag sensor circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1653/35 Seat Position Airbag Sensor Circuit Malfunction
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the seat position airbag sensor circuit.

·

Seat position airbag sensor malfunction

·

Airbag sensor assembly malfunction


for LHD:
·

No. 2 floor wire

·

Front seat inner belt assembly LH

·

Seat position airbag sensor

·

Airbag sensor assembly


for RHD:
·

Floor wire

·

Front seat inner belt assembly RH

·

Seat position airbag sensor

·

Airbag sensor assembly


Does not apply to test/check mode

WIRING DIAGRAM

for LHD:


C240622E09
0.552,2.917 2.365,3.292 1.813,0.375 10 false Seat Position Airbag Sensor 2.948,3.063 4.271,3.563 1.323,0.5 10 false Front Seat Inner Belt Assembly LH 2.948,2.917 3.281,3.073 0.333,0.156 10 false M4 5.344,3.063 7.01,3.448 1.667,0.385 10 false Airbag Sensor Assembly 5.344,2.917 5.688,3.135 0.344,0.219 10 false M7 1.854,0.813 2.083,1.156 0.229,0.344 10 false 2 4.24,0.813 4.458,1.156 0.219,0.344 10 false 4 1.854,1.979 2.135,2.375 0.281,0.396 10 false 1 4.24,1.979 4.469,2.354 0.229,0.375 10 false 3 5.208,0.813 5.469,1.031 0.26,0.219 10 false 9 5.146,1.979 5.323,2.135 0.177,0.156 10 false 17 3.813,0.813 4.292,1.208 0.479,0.396 10 false LSP+ 3.813,1.979 4.323,2.396 0.51,0.417 10 false LSP- 5.385,0.906 5.771,1.052 0.385,0.146 10 false LSP+ 5.385,2.073 5.76,2.219 0.375,0.146 10 false LSP- 1.427,0.802 1.865,1.052 0.438,0.25 10 false LSP+ 1.438,1.969 1.906,2.385 0.469,0.417 10 false LSP-


for RHD:


C240622E10
0.552,2.917 2.365,3.292 1.813,0.375 10 false Seat Position Airbag Sensor 2.948,3.063 4.281,3.625 1.333,0.563 10 false Front Seat Inner Belt Assembly RH 2.948,2.917 3.323,3.094 0.375,0.177 10 false L5 5.344,3.063 7.01,3.448 1.667,0.385 10 false Airbag Sensor Assembly 5.344,2.917 5.688,3.135 0.344,0.219 10 false L9 1.854,0.813 2.083,1.156 0.229,0.344 10 false 2 4.24,0.813 4.458,1.156 0.219,0.344 10 false 4 1.854,1.979 2.135,2.375 0.281,0.396 10 false 1 4.24,1.979 4.469,2.354 0.229,0.375 10 false 3 5.146,0.813 5.406,1.031 0.26,0.219 10 false 16 5.146,1.979 5.385,2.208 0.24,0.229 10 false 24 3.792,0.813 4.271,1.208 0.479,0.396 10 false RSP+ 3.813,1.979 4.323,2.396 0.51,0.417 10 false RSP- 5.385,0.906 5.854,1.229 0.469,0.323 10 false RSP+ 5.385,2.073 5.844,2.354 0.458,0.281 10 false RSP- 1.396,0.802 1.833,1.052 0.438,0.25 10 false RSP+ 1.438,1.969 1.906,2.385 0.469,0.417 10 false RSP-


CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK VEHICLE CONDITION
a.

Choose the model to be inspected.


Result:
Result Proceed to
LHD A
RHD B



A

2.CHECK CONNECTORS

B

13.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, front seat inner belt assembly LH and seat position airbag sensor.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, front seat inner belt assembly LH and seat position airbag sensor.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)

NG

REPLACE WIRE HARNESS

3.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)
a.
C265013C03
0.573,0.521 0.906,0.771 0.333,0.25 1.188,0.844 1.521,0.844 false 1.417,0.417 1.833,0.708 false 1.417,1.25 1.833,0.948 false 0.75,4.25 1.115,3.771 false 1.667,4.25 1.271,3.781 false 0.448,2.021 0.76,2.344 0.313,0.323 10 false *1 2.656,2.333 3.135,2.75 0.479,0.417 10 false *2 1.031,0.771 1.427,1.104 0.396,0.333 10 false *3 0.479,0.167 0.896,0.573 0.417,0.406 10 false *a 0.323,3.198 0.656,3.531 0.333,0.333 10 false *b 2.177,2.031 2.656,2.448 0.479,0.417 10 false A 1.927,2.031 2.406,2.448 0.479,0.417 10 false B 1.583,2.031 2.063,2.448 0.479,0.417 10 false C 1.427,2.031 1.906,2.448 0.479,0.417 10 false D 1.083,2.031 1.563,2.448 0.479,0.417 10 false E 0.833,2.031 1.313,2.448 0.479,0.417 10 false F 1.031,0.333 1.521,0.667 0.49,0.333 10 false LSP+ 1.073,1.177 1.531,1.521 0.458,0.344 10 false LSP- 0.656,0.563 1.052,0.896 0.396,0.333 10 false M7 1.51,4.25 1.906,4.583 0.396,0.333 10 false LSP+ 0.583,4.25 0.979,4.583 0.396,0.333 10 false LSP-
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Seat Position Airbag Sensor)


Connect the connectors to the front seat inner belt assembly LH and No. 2 floor wire.


b.

Using a service wire, connect terminals 9 (LSP+) and 17 (LSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (LSP+) - 1 (LSP-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)

NG

12.CHECK NO. 2 FLOOR WIRE (OPEN)
4.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)
a.
C283374C03
0.865,2.885 1.26,2.448 false 1.885,2.896 1.406,2.438 false 0.313,0.615 0.677,0.854 0.365,0.24 10 false *1 2.781,0.906 3.167,1.26 0.385,0.354 10 false *2 0.167,1.698 0.542,1.979 0.375,0.281 10 false *a 2.344,0.625 2.729,0.979 0.385,0.354 10 false A 2.031,0.625 2.417,0.979 0.385,0.354 10 false B 1.573,0.625 1.948,0.958 0.375,0.333 10 false C 1.417,0.625 1.792,0.958 0.375,0.333 10 false D 0.969,0.625 1.344,0.958 0.375,0.333 10 false E 0.656,0.625 1.031,0.958 0.375,0.333 10 false F 1.76,2.906 2.188,3.146 0.427,0.24 10 false LSP+ 0.698,2.896 1.125,3.135 0.427,0.24 10 false LSP-
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (LSP+) - 1 (LSP-) Always 1 MΩ or higher



Result:
Result
OK
NG



OK

5.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)

NG

11.CHECK NO. 2 FLOOR WIRE (SHORT)
5.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)
a.
C283374C03
0.865,2.885 1.26,2.448 false 1.885,2.896 1.406,2.438 false 0.313,0.615 0.677,0.854 0.365,0.24 10 false *1 2.781,0.906 3.167,1.26 0.385,0.354 10 false *2 0.167,1.698 0.542,1.979 0.375,0.281 10 false *a 2.344,0.625 2.729,0.979 0.385,0.354 10 false A 2.031,0.625 2.417,0.979 0.385,0.354 10 false B 1.573,0.625 1.948,0.958 0.375,0.333 10 false C 1.417,0.625 1.792,0.958 0.375,0.333 10 false D 0.969,0.625 1.344,0.958 0.375,0.333 10 false E 0.656,0.625 1.031,0.958 0.375,0.333 10 false F 1.76,2.906 2.188,3.146 0.427,0.24 10 false LSP+ 0.698,2.896 1.125,3.135 0.427,0.24 10 false LSP-
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (LSP+) - Body ground Ignition switch ON Below 1 V
1 (LSP-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

6.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)

NG

10.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
6.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)
a.
C283374C03
0.865,2.885 1.26,2.448 false 1.885,2.896 1.406,2.438 false 0.313,0.615 0.677,0.854 0.365,0.24 10 false *1 2.781,0.906 3.167,1.26 0.385,0.354 10 false *2 0.167,1.698 0.542,1.979 0.375,0.281 10 false *a 2.344,0.625 2.729,0.979 0.385,0.354 10 false A 2.031,0.625 2.417,0.979 0.385,0.354 10 false B 1.573,0.625 1.948,0.958 0.375,0.333 10 false C 1.417,0.625 1.792,0.958 0.375,0.333 10 false D 0.969,0.625 1.344,0.958 0.375,0.333 10 false E 0.656,0.625 1.031,0.958 0.375,0.333 10 false F 1.76,2.906 2.188,3.146 0.427,0.24 10 false LSP+ 0.698,2.896 1.125,3.135 0.427,0.24 10 false LSP-
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (LSP+) - Body ground Always 1 MΩ or higher
1 (LSP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK DTC

NG

9.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
7.CHECK DTC
a.
C238211C05
0.5,0.833 0.719,1.083 0.219,0.25 10 false *1 0.833,0.823 1.031,1.094 0.198,0.271 10 false F 0.99,0.823 1.177,1.115 0.188,0.292 10 false E 1.438,0.823 1.677,1.104 0.24,0.281 10 false D 1.594,0.823 1.802,1.042 0.208,0.219 10 false C 2.042,0.823 2.25,1.063 0.208,0.24 10 false B 2.198,0.823 2.406,1.01 0.208,0.188 10 false A 2.615,1.104 2.896,1.375 0.281,0.271 10 false *2
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and seat position airbag sensor.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653/35 is not output.


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



Result:
Result
OK
NG



OK

NG

8.CHECK SEAT POSITION AIRBAG SENSOR
8.CHECK SEAT POSITION AIRBAG SENSOR
a.
C238211C05
0.5,0.833 0.719,1.083 0.219,0.25 10 false *1 0.833,0.823 1.031,1.094 0.198,0.271 10 false F 0.99,0.823 1.177,1.115 0.188,0.292 10 false E 1.438,0.823 1.677,1.104 0.24,0.281 10 false D 1.594,0.823 1.802,1.042 0.208,0.219 10 false C 2.042,0.823 2.25,1.063 0.208,0.24 10 false B 2.198,0.823 2.406,1.01 0.208,0.188 10 false A 2.615,1.104 2.896,1.375 0.281,0.271 10 false *2
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Replace the seat position airbag sensor with a known good one.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653/35 is not output.


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Restore the seat position airbag sensor that was installed for testing to its original location.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL


Result:
Proceed to
OK
NG



OK

NG

9.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
a.
C283376C03
0.896,2.177 1.229,2.417 0.333,0.24 1.188,1.042 1.188,0.708 false 1.948,0.552 1.948,0.188 1.948,0.188 2.115,0.188 false 1.438,2.813 1.813,2.469 false 2.406,2.813 2,2.469 false 0.292,0.563 0.646,0.813 0.354,0.25 10 false *1 2.844,0.854 3.146,1.125 0.302,0.271 10 false *2 1.115,1.052 1.365,1.323 0.25,0.271 10 false *3 2.146,0.115 2.448,0.344 0.302,0.229 10 false *4 0.74,1.604 1.021,1.875 0.281,0.271 10 false *a 2.448,0.573 2.635,0.823 0.188,0.25 10 false A 2.135,0.563 2.323,0.813 0.188,0.25 10 false B 1.677,0.563 1.865,0.813 0.188,0.25 10 false C 1.365,0.563 1.552,0.813 0.188,0.25 10 false D 0.917,0.563 1.104,0.813 0.188,0.25 10 false E 0.604,0.563 0.792,0.813 0.188,0.25 10 false F 2.302,2.823 2.75,3.094 0.448,0.271 10 false LSP+ 0.979,2.219 1.313,2.5 0.333,0.281 10 false M4 1.281,2.823 1.729,3.094 0.448,0.271 10 false LSP-
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Front Seat Inner Belt Assembly LH
*4 No. 2 Floor Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)


Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-4 (LSP+) - Body ground Always 1 MΩ or higher
M4-3 (LSP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 2 FLOOR WIRE

10.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
a.
C283376C03
0.896,2.177 1.229,2.417 0.333,0.24 1.188,1.042 1.188,0.708 false 1.948,0.552 1.948,0.188 1.948,0.188 2.115,0.188 false 1.438,2.813 1.813,2.469 false 2.406,2.813 2,2.469 false 0.292,0.563 0.646,0.813 0.354,0.25 10 false *1 2.844,0.854 3.146,1.125 0.302,0.271 10 false *2 1.115,1.052 1.365,1.323 0.25,0.271 10 false *3 2.146,0.115 2.448,0.344 0.302,0.229 10 false *4 0.74,1.604 1.021,1.875 0.281,0.271 10 false *a 2.448,0.573 2.635,0.823 0.188,0.25 10 false A 2.135,0.563 2.323,0.813 0.188,0.25 10 false B 1.677,0.563 1.865,0.813 0.188,0.25 10 false C 1.365,0.563 1.552,0.813 0.188,0.25 10 false D 0.917,0.563 1.104,0.813 0.188,0.25 10 false E 0.604,0.563 0.792,0.813 0.188,0.25 10 false F 2.302,2.823 2.75,3.094 0.448,0.271 10 false LSP+ 0.979,2.219 1.313,2.5 0.333,0.281 10 false M4 1.281,2.823 1.729,3.094 0.448,0.271 10 false LSP-
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Front Seat Inner Belt Assembly LH
*4 No. 2 Floor Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)


Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M4-4 (LSP+) - Body ground Ignition switch ON Below 1 V
M4-3 (LSP-) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 2 FLOOR WIRE

11.CHECK NO. 2 FLOOR WIRE (SHORT)
a.
C283376C03
0.896,2.177 1.229,2.417 0.333,0.24 1.188,1.042 1.188,0.708 false 1.948,0.552 1.948,0.188 1.948,0.188 2.115,0.188 false 1.438,2.813 1.813,2.469 false 2.406,2.813 2,2.469 false 0.292,0.563 0.646,0.813 0.354,0.25 10 false *1 2.844,0.854 3.146,1.125 0.302,0.271 10 false *2 1.115,1.052 1.365,1.323 0.25,0.271 10 false *3 2.146,0.115 2.448,0.344 0.302,0.229 10 false *4 0.74,1.604 1.021,1.875 0.281,0.271 10 false *a 2.448,0.573 2.635,0.823 0.188,0.25 10 false A 2.135,0.563 2.323,0.813 0.188,0.25 10 false B 1.677,0.563 1.865,0.813 0.188,0.25 10 false C 1.365,0.563 1.552,0.813 0.188,0.25 10 false D 0.917,0.563 1.104,0.813 0.188,0.25 10 false E 0.604,0.563 0.792,0.813 0.188,0.25 10 false F 2.302,2.823 2.75,3.094 0.448,0.271 10 false LSP+ 0.979,2.219 1.313,2.5 0.333,0.281 10 false M4 1.281,2.823 1.729,3.094 0.448,0.271 10 false LSP-
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Front Seat Inner Belt Assembly LH
*4 No. 2 Floor Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)


Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-4 (LSP+) - M4-3 (LSP-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 2 FLOOR WIRE

12.CHECK NO. 2 FLOOR WIRE (OPEN)
a.
C265015C03
0.583,3.667 0.948,3.917 0.365,0.25 0.583,0.656 0.917,0.906 0.333,0.25 1.24,2.542 1.24,2.208 false 1.833,2.073 1.833,1.823 1.833,1.823 1.5,1.823 false 1.323,0.865 1.573,0.865 false 1.417,0.5 1.885,0.729 false 1.417,1.25 1.885,0.938 false 1.167,4.167 1.49,3.854 false 2,4.167 1.635,3.854 false 0.396,2.063 0.792,2.479 0.396,0.417 10 false *1 2.677,2.396 3.094,2.802 0.417,0.406 10 false *2 1.177,2.563 1.51,2.885 0.333,0.323 10 false *3 1.344,1.75 1.74,2.083 0.396,0.333 10 false *4 1.167,0.781 1.5,1.167 0.333,0.385 10 false *5 0.521,0.177 0.833,0.583 0.313,0.406 10 false *a 0.344,3.188 0.74,3.51 0.396,0.323 10 false *b 2.208,2.073 2.625,2.479 0.417,0.406 10 false A 1.969,2.073 2.385,2.479 0.417,0.406 10 false B 1.625,2.073 2.042,2.479 0.417,0.406 10 false C 1.375,2.073 1.792,2.479 0.417,0.406 10 false D 1.031,2.073 1.448,2.479 0.417,0.406 10 false E 0.781,2.073 1.198,2.479 0.417,0.406 10 false F 1.042,0.417 1.542,0.833 0.5,0.417 10 false LSP+ 1.073,1.177 1.573,1.594 0.5,0.417 10 false LSP- 1.885,4.167 2.385,4.583 0.5,0.417 10 false LSP+ 1,4.167 1.5,4.583 0.5,0.417 10 false LSP- 0.688,3.708 1.188,4.125 0.5,0.417 10 false M4 0.667,0.698 1.167,1.115 0.5,0.417 10 false M7
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Front Seat Inner Belt Assembly LH
*4 No. 2 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly LH)


Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M4-4 (LSP+) - M4-3 (LSP-) Always Below 1 Ω



c.

Disconnect the service wire from the connector B.


Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 2 FLOOR WIRE

13.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, front seat inner belt assembly RH and seat position airbag sensor.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, front seat inner belt assembly RH and seat position airbag sensor.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

14.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)

NG

REPLACE WIRE HARNESS

14.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)
a.
C284677C03
0.583,0.677 0.917,0.917 0.333,0.24 2.115,0.802 2.5,0.5 false 2.125,1.073 2.5,1.333 false 1.083,4.25 1.5,3.792 false 2.167,4.25 1.698,3.792 false 2.792,0.927 2.458,0.927 false 0.438,2.448 0.833,2.781 0.396,0.333 10 false *1 2.646,2.167 2.958,2.583 0.313,0.417 10 false *2 2.823,0.844 3.125,1.167 0.302,0.323 10 false *3 0.521,0.167 0.833,0.5 0.313,0.333 10 false *a 0.344,3.229 0.656,3.552 0.313,0.323 10 false *b 2.052,4.25 2.469,4.583 0.417,0.333 10 false RSP+ 2.531,1.25 3.115,1.573 0.583,0.323 10 false RSP- 0.677,0.719 1.146,1.042 0.469,0.323 10 false L9 2.177,2.469 2.49,2.885 0.313,0.417 10 false A 1.927,2.458 2.24,2.875 0.313,0.417 10 false B 1.583,2.458 1.896,2.875 0.313,0.417 10 false C 1.427,2.458 1.74,2.875 0.313,0.417 10 false D 1.083,2.458 1.396,2.875 0.313,0.417 10 false E 0.844,2.458 1.156,2.875 0.313,0.417 10 false F 2.531,0.417 3.031,0.75 0.5,0.333 10 false RSP+ 0.938,4.25 1.438,4.656 0.5,0.406 10 false RSP-
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Seat Position Airbag Sensor)


Connect the connectors to the front seat inner belt assembly RH and floor wire.


b.

Using a service wire, connect terminals 16 (RSP+) and 24 (RSP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (RSP+) - 1 (RSP-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)

NG

23.CHECK FLOOR WIRE (OPEN)
15.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)
a.
C284678C02
1,2.917 1.438,2.417 false 2.083,2.917 1.667,2.417 false 0.427,0.969 0.76,1.219 0.333,0.25 10 false *1 2.667,0.677 3.063,1.01 0.396,0.333 10 false *2 0.354,1.74 0.75,2.156 0.396,0.417 10 false *a 2.198,0.969 2.594,1.302 0.396,0.333 10 false A 1.927,0.979 2.323,1.313 0.396,0.333 10 false B 1.583,0.979 1.979,1.313 0.396,0.333 10 false C 1.417,0.979 1.813,1.313 0.396,0.333 10 false D 1.073,0.979 1.469,1.313 0.396,0.333 10 false E 0.802,0.969 1.198,1.302 0.396,0.333 10 false F 1.969,2.917 2.448,3.25 0.479,0.333 10 false RSP+ 0.844,2.917 1.51,3.25 0.667,0.333 10 false RSP-
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (RSP+) - 1 (RSP-) Always 1 MΩ or higher



Result:
Result
OK
NG



OK

16.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)

NG

22.CHECK FLOOR WIRE (SHORT)
16.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)
a.
C284678C02
1,2.917 1.438,2.417 false 2.083,2.917 1.667,2.417 false 0.427,0.969 0.76,1.219 0.333,0.25 10 false *1 2.667,0.677 3.063,1.01 0.396,0.333 10 false *2 0.354,1.74 0.75,2.156 0.396,0.417 10 false *a 2.198,0.969 2.594,1.302 0.396,0.333 10 false A 1.927,0.979 2.323,1.313 0.396,0.333 10 false B 1.583,0.979 1.979,1.313 0.396,0.333 10 false C 1.417,0.979 1.813,1.313 0.396,0.333 10 false D 1.073,0.979 1.469,1.313 0.396,0.333 10 false E 0.802,0.969 1.198,1.302 0.396,0.333 10 false F 1.969,2.917 2.448,3.25 0.479,0.333 10 false RSP+ 0.844,2.917 1.51,3.25 0.667,0.333 10 false RSP-
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (RSP+) - Body ground Ignition switch ON Below 1 V
1 (RSP-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

17.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)

NG

21.CHECK FLOOR WIRE (SHORT TO B+)
17.CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)
a.
C284678C02
1,2.917 1.438,2.417 false 2.083,2.917 1.667,2.417 false 0.427,0.969 0.76,1.219 0.333,0.25 10 false *1 2.667,0.677 3.063,1.01 0.396,0.333 10 false *2 0.354,1.74 0.75,2.156 0.396,0.417 10 false *a 2.198,0.969 2.594,1.302 0.396,0.333 10 false A 1.927,0.979 2.323,1.313 0.396,0.333 10 false B 1.583,0.979 1.979,1.313 0.396,0.333 10 false C 1.417,0.979 1.813,1.313 0.396,0.333 10 false D 1.073,0.979 1.469,1.313 0.396,0.333 10 false E 0.802,0.969 1.198,1.302 0.396,0.333 10 false F 1.969,2.917 2.448,3.25 0.479,0.333 10 false RSP+ 0.844,2.917 1.51,3.25 0.667,0.333 10 false RSP-
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*a Front view of wire harness connector
(to Seat Position Airbag Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (RSP+) - Body ground Always 1 MΩ or higher
1 (RSP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

18.CHECK DTC

NG

20.CHECK FLOOR WIRE (SHORT TO GROUND)
18.CHECK DTC
a.
C284676C01
0.531,1.229 0.906,1.531 0.375,0.302 10 false *1 2.635,0.938 2.979,1.26 0.344,0.323 10 false *2 2.198,1.219 2.542,1.542 0.344,0.323 10 false A 2.042,1.229 2.385,1.552 0.344,0.323 10 false B 1.594,1.229 1.938,1.552 0.344,0.323 10 false C 1.438,1.229 1.781,1.552 0.344,0.323 10 false D 0.99,1.229 1.333,1.552 0.344,0.323 10 false E 0.833,1.229 1.177,1.552 0.344,0.323 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and seat position airbag sensor.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653/35 is not output.


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



Result:
Result
OK
NG



OK

NG

19.CHECK SEAT POSITION AIRBAG SENSOR
19.CHECK SEAT POSITION AIRBAG SENSOR
a.
C284676C01
0.531,1.229 0.906,1.531 0.375,0.302 10 false *1 2.635,0.938 2.979,1.26 0.344,0.323 10 false *2 2.198,1.219 2.542,1.542 0.344,0.323 10 false A 2.042,1.229 2.385,1.552 0.344,0.323 10 false B 1.594,1.229 1.938,1.552 0.344,0.323 10 false C 1.438,1.229 1.781,1.552 0.344,0.323 10 false D 0.99,1.229 1.333,1.552 0.344,0.323 10 false E 0.833,1.229 1.177,1.552 0.344,0.323 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Replace the seat position airbag sensor with a known good one.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1653/35 is not output.


HINT:

Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Restore the seat position airbag sensor that was installed for testing to its original location.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SEAT POSITION SENSOR>REMOVAL


Result:
Proceed to
OK
NG



OK

NG

20.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C284680C02
0.552,2.26 0.844,2.49 0.292,0.229 1.083,2.917 1.458,2.531 false 2.083,2.917 1.677,2.531 false 1.25,1.365 1.25,1.115 false 1.854,0.979 1.854,0.646 1.854,0.646 1.688,0.646 false 0.406,0.969 0.729,1.333 0.323,0.365 10 false *1 2.708,0.677 3.021,1.094 0.313,0.417 10 false *2 1.198,1.375 1.51,1.708 0.313,0.333 10 false *3 1.521,0.563 1.833,0.969 0.313,0.406 10 false *4 0.354,1.75 0.75,2.156 0.396,0.406 10 false *a 0.917,2.917 1.417,3.323 0.5,0.406 10 false RSP- 1.927,2.917 2.427,3.323 0.5,0.406 10 false RSP+ 0.625,2.292 1.125,2.698 0.5,0.406 10 false L5 2.24,0.979 2.552,1.396 0.313,0.417 10 false A 1.99,0.979 2.302,1.396 0.313,0.417 10 false B 1.635,0.969 1.948,1.385 0.313,0.417 10 false C 1.375,0.969 1.688,1.385 0.313,0.417 10 false D 1.031,0.958 1.344,1.375 0.313,0.417 10 false E 0.781,0.958 1.094,1.375 0.313,0.417 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Front Seat Inner Belt Assembly RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)


Disconnect the floor wire from the front seat inner belt assembly RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L5-4 (RSP+) - Body ground Always 1 MΩ or higher
L5-3 (RSP-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE FLOOR WIRE

21.CHECK FLOOR WIRE (SHORT TO B+)
a.
C284680C02
0.552,2.26 0.844,2.49 0.292,0.229 1.083,2.917 1.458,2.531 false 2.083,2.917 1.677,2.531 false 1.25,1.365 1.25,1.115 false 1.854,0.979 1.854,0.646 1.854,0.646 1.688,0.646 false 0.406,0.969 0.729,1.333 0.323,0.365 10 false *1 2.708,0.677 3.021,1.094 0.313,0.417 10 false *2 1.198,1.375 1.51,1.708 0.313,0.333 10 false *3 1.521,0.563 1.833,0.969 0.313,0.406 10 false *4 0.354,1.75 0.75,2.156 0.396,0.406 10 false *a 0.917,2.917 1.417,3.323 0.5,0.406 10 false RSP- 1.927,2.917 2.427,3.323 0.5,0.406 10 false RSP+ 0.625,2.292 1.125,2.698 0.5,0.406 10 false L5 2.24,0.979 2.552,1.396 0.313,0.417 10 false A 1.99,0.979 2.302,1.396 0.313,0.417 10 false B 1.635,0.969 1.948,1.385 0.313,0.417 10 false C 1.375,0.969 1.688,1.385 0.313,0.417 10 false D 1.031,0.958 1.344,1.375 0.313,0.417 10 false E 0.781,0.958 1.094,1.375 0.313,0.417 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Front Seat Inner Belt Assembly RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)


Disconnect the floor wire from the front seat inner belt assembly RH.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L5-4 (RSP+) - Body ground Ignition switch ON Below 1 V
L5-3 (RSP-) - Body ground Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE FLOOR WIRE

22.CHECK FLOOR WIRE (SHORT)
a.
C284680C02
0.552,2.26 0.844,2.49 0.292,0.229 1.083,2.917 1.458,2.531 false 2.083,2.917 1.677,2.531 false 1.25,1.365 1.25,1.115 false 1.854,0.979 1.854,0.646 1.854,0.646 1.688,0.646 false 0.406,0.969 0.729,1.333 0.323,0.365 10 false *1 2.708,0.677 3.021,1.094 0.313,0.417 10 false *2 1.198,1.375 1.51,1.708 0.313,0.333 10 false *3 1.521,0.563 1.833,0.969 0.313,0.406 10 false *4 0.354,1.75 0.75,2.156 0.396,0.406 10 false *a 0.917,2.917 1.417,3.323 0.5,0.406 10 false RSP- 1.927,2.917 2.427,3.323 0.5,0.406 10 false RSP+ 0.625,2.292 1.125,2.698 0.5,0.406 10 false L5 2.24,0.979 2.552,1.396 0.313,0.417 10 false A 1.99,0.979 2.302,1.396 0.313,0.417 10 false B 1.635,0.969 1.948,1.385 0.313,0.417 10 false C 1.375,0.969 1.688,1.385 0.313,0.417 10 false D 1.031,0.958 1.344,1.375 0.313,0.417 10 false E 0.781,0.958 1.094,1.375 0.313,0.417 10 false F
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Front Seat Inner Belt Assembly RH
*4 Floor Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)


Disconnect the floor wire from the front seat inner belt assembly RH.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L5-4 (RSP+) - L5-3 (RSP-) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE FLOOR WIRE

23.CHECK FLOOR WIRE (OPEN)
a.
C284679C02
0.615,3.646 0.896,3.865 0.281,0.219 0.667,0.625 0.99,0.865 0.323,0.24 2.146,0.74 2.5,0.5 false 2.167,1 2.5,1.25 false 2.469,0.885 2.719,0.885 false 1.083,4.25 1.469,3.865 false 2.083,4.25 1.688,3.865 false 1.24,2.792 1.24,2.542 false 1.823,2.406 1.823,2.073 1.823,2.073 1.656,2.073 false 0.427,2.385 0.823,2.719 0.396,0.333 10 false *1 2.688,2.094 3.083,2.5 0.396,0.406 10 false *2 1.177,2.813 1.49,3.146 0.313,0.333 10 false *3 1.51,2 1.906,2.24 0.396,0.24 10 false *4 2.729,0.802 3.063,1.135 0.333,0.333 10 false *5 0.583,0.177 0.917,0.583 0.333,0.406 10 false *a 0.365,3.146 0.698,3.625 0.333,0.479 10 false *b 2.531,0.417 3.115,0.833 0.583,0.417 10 false RSP+ 2.531,1.167 3.198,1.583 0.667,0.417 10 false RSP- 0.917,4.25 1.583,4.667 0.667,0.417 10 false RSP- 1.958,4.25 2.625,4.667 0.667,0.417 10 false RSP+ 2.208,2.396 2.604,2.802 0.396,0.406 10 false A 1.958,2.396 2.354,2.802 0.396,0.406 10 false B 1.625,2.396 2.021,2.802 0.396,0.406 10 false C 1.375,2.396 1.771,2.802 0.396,0.406 10 false D 1.021,2.396 1.417,2.802 0.396,0.406 10 false E 0.792,2.396 1.188,2.802 0.396,0.406 10 false F 0.688,3.667 1.354,4.083 0.667,0.417 10 false L5 0.76,0.667 1.427,1.083 0.667,0.417 10 false L9
*1 Seat Position Airbag Sensor
*2 Airbag Sensor Assembly
*3 Front Seat Inner Belt Assembly RH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)


Disconnect the floor wire from the front seat inner belt assembly RH.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L5-4 (RSP+) - L5-3 (RSP-) Always Below 1 Ω



c.

Disconnect the service wire from the connector B.


Result:
Proceed to
OK
NG



OK

NG

REPLACE FLOOR WIRE