Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM3160E _58 Vehicle Interior _019710 SUPPLEMENTAL RESTRAINT SYSTEMS _0100809 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1655/37  Seat Belt Buckle Switch RH Circuit Malfunction  


DESCRIPTION

The seat belt buckle switch RH circuit consists of the airbag sensor assembly and seat belt buckle switch RH (front seat inner belt assembly RH).

DTC B1655/37 is stored when a malfunction is detected in the seat belt buckle switch RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1655/37 Seat Belt Buckle Switch RH Circuit Malfunction
·

The airbag sensor assembly detects a line short, short to ground or B+, or an open in the seat belt buckle switch RH circuit.

·

Seat belt buckle switch RH malfunction

·

Airbag sensor assembly malfunction


·

Floor wire

·

Seat belt buckle switch RH (Front seat inner belt assembly RH)

·

Airbag sensor assembly


Does not apply to test/check mode

WIRING DIAGRAM

C295791E01
0.552,2.438 1.635,2.771 1.083,0.333 10 false L6*1, L5*2 0.552,2.604 3.052,2.99 2.5,0.385 10 false Seat Belt Buckle Switch RH (Front Seat Inner Belt Assembly RH) 5.365,2.438 6.146,2.865 0.781,0.427 10 false L9 5.365,2.604 7.104,3.083 1.74,0.479 10 false Airbag Sensor Assembly 5.375,0.698 6.021,1.052 0.646,0.354 10 false RBE+ 5.375,1.865 6.021,2.219 0.646,0.354 10 false RBE- 5.146,0.594 5.563,1.01 0.417,0.417 10 false 15 5.146,1.76 5.563,2.177 0.417,0.417 10 false 23 1.833,0.594 2.479,0.948 0.646,0.354 10 false RBE+ 1.865,1.76 2.51,2.115 0.646,0.354 10 false RBE- 0.25,3.177 1.292,3.573 1.042,0.396 10 false *1: for LHD 0.25,3.458 1.167,3.719 0.917,0.26 10 false *2: for RHD 2.292,0.594 3.167,0.969 0.875,0.375 10 false 1*1, 2*2 2.292,1.76 3.167,2.135 0.875,0.375 10 false 2*1, 1*2

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly and front seat inner belt assembly RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly and front seat inner belt assembly RH.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

2.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

2.CHECK FLOOR WIRE (OPEN)
a.
C284141C02
0.49,3.656 0.792,3.885 0.302,0.229 0.667,0.646 1,0.896 0.333,0.25 0.49,3.354 0.792,3.583 0.302,0.229 0.927,4.073 1.479,3.688 false 2.219,4.073 1.688,3.688 false 2.5,0.417 2.01,0.729 false 2.5,1.333 2.01,1.021 false 2.708,0.875 2.375,0.875 false 1.531,2.396 1.531,1.979 1.531,1.979 1.365,1.979 false 0.458,2.385 0.854,2.719 0.396,0.333 10 false *1 2.604,2.083 3,2.49 0.396,0.406 10 false *2 1.219,1.896 1.552,2.146 0.333,0.25 10 false *3 2.75,0.802 3.063,1.135 0.313,0.333 10 false *4 0.521,0.167 0.917,0.667 0.396,0.5 10 false *a 0.375,3.135 0.708,3.552 0.333,0.417 10 false *b 0.635,4.083 1.313,4.292 0.677,0.208 10 false RBE+*A 2,4.083 2.698,4.313 0.698,0.229 10 false RBE-*A 0.573,3.698 0.99,4.031 0.417,0.333 10 false L5 2.531,1.26 3.115,1.594 0.583,0.333 10 false RBE- 2.531,0.333 3.115,0.667 0.583,0.333 10 false RBE+ 0.76,0.688 1.177,1.021 0.417,0.333 10 false L9 2.125,2.396 2.521,2.802 0.396,0.406 10 false A 1.771,2.396 2.167,2.802 0.396,0.406 10 false B 1.219,2.396 1.615,2.802 0.396,0.406 10 false C 0.865,2.385 1.26,2.792 0.396,0.406 10 false D 0.635,4.25 1.302,4.458 0.667,0.208 10 false RBE-*B 2,4.25 2.688,4.479 0.688,0.229 10 false RBE+*B 0.823,3.698 1.24,4.031 0.417,0.333 10 false *B 0.573,3.396 0.99,3.729 0.417,0.333 10 false L6 0.823,3.396 1.24,3.729 0.417,0.333 10 false *A
*A for LHD
*B for RHD
*1 Front Seat Inner Belt Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)


Using a service wire, connect terminals 15 (RBE+) and 23 (RBE-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
L6-1 (RBE+) - L6-2 (RBE-) Always Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition
L5-2 (RBE+) - L5-1 (RBE-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


Result:
Proceed to
OK
NG



OK

3.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (SHORT)
a.
C284675C02
0.458,2.354 0.771,2.573 0.313,0.219 0.458,2.052 0.771,2.271 0.313,0.219 1.552,0.979 1.552,0.646 1.552,0.646 1.385,0.646 false 1.031,2.813 1.438,2.333 false 2.135,2.823 1.698,2.323 false 0.438,1 0.833,1.333 0.396,0.333 10 false *1 2.667,0.667 3.083,1 0.417,0.333 10 false *2 1.229,0.563 1.563,0.979 0.333,0.417 10 false *3 0.354,1.75 0.75,2.083 0.396,0.333 10 false *a 2.146,0.958 2.563,1.292 0.417,0.333 10 false A 1.792,0.979 2.208,1.313 0.417,0.333 10 false B 1.219,0.969 1.635,1.302 0.417,0.333 10 false C 0.865,0.969 1.281,1.302 0.417,0.333 10 false D 0.771,2.833 1.458,3.167 0.688,0.333 10 false RBE+*A 1.917,2.833 2.552,3.167 0.635,0.333 10 false RBE-*A 0.542,2.385 0.875,2.719 0.333,0.333 10 false L5 0.771,3 1.458,3.333 0.688,0.333 10 false RBE-*B 1.917,3 2.583,3.333 0.667,0.333 10 false RBE+*B 0.802,2.385 1.135,2.719 0.333,0.333 10 false *B 0.542,2.083 0.875,2.417 0.333,0.333 10 false L6 0.802,2.083 1.135,2.417 0.333,0.333 10 false *A
*A for LHD
*B for RHD
*1 Front Seat Inner Belt Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
L6-1 (RBE+) - L6-2 (RBE-) Always 1 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition
L5-2 (RBE+) - L5-1 (RBE-) Always 1 MΩ or higher



Result:
Result
OK
NG



OK

4.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT TO B+)
a.
C284675C02
0.458,2.354 0.771,2.573 0.313,0.219 0.458,2.052 0.771,2.271 0.313,0.219 1.552,0.979 1.552,0.646 1.552,0.646 1.385,0.646 false 1.031,2.813 1.438,2.333 false 2.135,2.823 1.698,2.323 false 0.438,1 0.833,1.333 0.396,0.333 10 false *1 2.667,0.667 3.083,1 0.417,0.333 10 false *2 1.229,0.563 1.563,0.979 0.333,0.417 10 false *3 0.354,1.75 0.75,2.083 0.396,0.333 10 false *a 2.146,0.958 2.563,1.292 0.417,0.333 10 false A 1.792,0.979 2.208,1.313 0.417,0.333 10 false B 1.219,0.969 1.635,1.302 0.417,0.333 10 false C 0.865,0.969 1.281,1.302 0.417,0.333 10 false D 0.771,2.833 1.458,3.167 0.688,0.333 10 false RBE+*A 1.917,2.833 2.552,3.167 0.635,0.333 10 false RBE-*A 0.542,2.385 0.875,2.719 0.333,0.333 10 false L5 0.771,3 1.458,3.333 0.688,0.333 10 false RBE-*B 1.917,3 2.583,3.333 0.667,0.333 10 false RBE+*B 0.802,2.385 1.135,2.719 0.333,0.333 10 false *B 0.542,2.083 0.875,2.417 0.333,0.333 10 false L6 0.802,2.083 1.135,2.417 0.333,0.333 10 false *A
*A for LHD
*B for RHD
*1 Front Seat Inner Belt Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition
L6-1 (RBE+) - Body ground Ignition switch ON Below 1 V
L6-2 (RBE-) - Body ground Ignition switch ON Below 1 V

for RHD:
Tester Connection Condition Specified Condition
L5-2 (RBE+) - Body ground Ignition switch ON Below 1 V
L5-1 (RBE-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

5.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
C284675C02
0.458,2.354 0.771,2.573 0.313,0.219 0.458,2.052 0.771,2.271 0.313,0.219 1.552,0.979 1.552,0.646 1.552,0.646 1.385,0.646 false 1.031,2.813 1.438,2.333 false 2.135,2.823 1.698,2.323 false 0.438,1 0.833,1.333 0.396,0.333 10 false *1 2.667,0.667 3.083,1 0.417,0.333 10 false *2 1.229,0.563 1.563,0.979 0.333,0.417 10 false *3 0.354,1.75 0.75,2.083 0.396,0.333 10 false *a 2.146,0.958 2.563,1.292 0.417,0.333 10 false A 1.792,0.979 2.208,1.313 0.417,0.333 10 false B 1.219,0.969 1.635,1.302 0.417,0.333 10 false C 0.865,0.969 1.281,1.302 0.417,0.333 10 false D 0.771,2.833 1.458,3.167 0.688,0.333 10 false RBE+*A 1.917,2.833 2.552,3.167 0.635,0.333 10 false RBE-*A 0.542,2.385 0.875,2.719 0.333,0.333 10 false L5 0.771,3 1.458,3.333 0.688,0.333 10 false RBE-*B 1.917,3 2.583,3.333 0.667,0.333 10 false RBE+*B 0.802,2.385 1.135,2.719 0.333,0.333 10 false *B 0.542,2.083 0.875,2.417 0.333,0.333 10 false L6 0.802,2.083 1.135,2.417 0.333,0.333 10 false *A
*A for LHD
*B for RHD
*1 Front Seat Inner Belt Assembly RH
*2 Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Front Seat Inner Belt Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
L6-1 (RBE+) - Body ground Always 1 MΩ or higher
L6-2 (RBE-) - Body ground Always 1 MΩ or higher

for RHD:
Tester Connection Condition Specified Condition
L5-2 (RBE+) - Body ground Always 1 MΩ or higher
L5-1 (RBE-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK DTC

NG

REPLACE FLOOR WIRE

6.CHECK DTC
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Front Seat Inner Belt Assembly RH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly and front seat inner belt assembly RH.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1655/37 is not output.


HINT:

Codes other than DTC B1655/37 may be output at this time, but they are not related to this check.



Result:
Result
OK
NG



OK

NG

7.CHECK FRONT SEAT INNER BELT ASSEMBLY RH
7.CHECK FRONT SEAT INNER BELT ASSEMBLY RH
a.
C238218C02
0.802,1.156 1.438,1.75 0.635,0.594 10 false *1 2.302,0.885 2.594,1.208 0.292,0.323 10 false *2 1.719,1.167 2.021,1.604 0.302,0.438 10 false B 1.875,1.167 2.271,1.625 0.396,0.458 10 false A 1.271,1.167 1.552,1.583 0.281,0.417 10 false C 1.115,1.167 1.594,1.729 0.479,0.563 10 false D
*1 Front Seat Inner Belt Assembly RH
*2 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Replace the front seat inner belt assembly RH with a known good one.

for Manual Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Manual Seat)>REMOVAL

for Power Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Power Seat)>REMOVAL

HINT:

Perform the following inspection using known good parts from another vehicle if possible.



d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1655/37 is not output.


HINT:

Codes other than DTC B1655/37 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Restore the front seat inner belt assembly RH that was installed for testing to its original location.

for Manual Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Manual Seat)>REMOVAL

for Power Seat: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY(for Power Seat)>REMOVAL


Result:
Proceed to
OK
NG



OK

NG