Home › Vehicle Exterior › MIRROR (EXT) › OUTER REAR VIEW MIRROR
RM3160E _59 Vehicle Exterior _019720 MIRROR (EXT) _0101074 OUTER REAR VIEW MIRROR G

MIRROR (EXT)  OUTER REAR VIEW MIRROR  INSPECTION  


PROCEDURE

Hide 87910 1.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/o Memory)

a.

Check the operation of the mirror surface.

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B357252
1.583,2.719 1.583,3.167 1.583,3.167 2.25,3.167 false 1.302,3.167 1.469,3.167 1.469,3.167 1.469,2.719 false 1.469,2.5 1.469,1.917 1.469,1.917 1.219,1.917 false 0.5,1.75 0.667,1.917 0.167,0.167 10 false *a 0.969,1.833 1.25,2 0.281,0.167 10 false MV 2.333,3.063 2.583,3.229 0.25,0.167 10 false M+ 1.01,3.063 1.26,3.229 0.25,0.167 10 false MH
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply battery voltage and check the operation of the mirror surface.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 1 (MV)
Battery negative (-) → Terminal 7 (M+)
Turns upward
Battery positive (+) → Terminal 7 (M+)
Battery negative (-) → Terminal 1 (MV)
Turns downward
Battery positive (+) → Terminal 6 (MH)
Battery negative (-) → Terminal 7 (M+)
Turns left
Battery positive (+) → Terminal 7 (M+)
Battery negative (-) → Terminal 6 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



b.

Check the operation of the mirror heater. (w/ Mirror Heater)

i.
B364133
1.615,2.5 1.615,1.865 1.615,1.865 2.083,1.865 false 1.885,2.708 1.885,3.146 1.885,3.146 2.24,3.146 false 0.167,0.188 0.479,0.385 0.313,0.198 10 false *a 2.156,1.771 2.656,2 0.5,0.229 10 false + 2.292,3.063 2.792,3.292 0.5,0.229 10 false E
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+) - 9 (E) 25°C (77°F) 3.57 to 4.83 Ω


If the result is not as specified, replace the outer rear view mirror assembly RH.


iii.

Connect a cable from the positive (+) battery terminal to terminal 2 and the negative (-) battery terminal to terminal 9, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.



c.

Check the operation of the retractable mirror. (w/ Retract Mirror)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.
B357253
2.188,4.313 1.76,4.313 1.76,4.313 1.76,3.906 false 2.021,3.198 1.76,3.198 1.76,3.198 1.76,3.708 false 2.146,0.135 2.313,0.302 0.167,0.167 10 false *a 2.583,1.083 2.75,1.25 0.167,0.167 10 false *b 2.479,1.979 2.646,2.146 0.167,0.167 10 false *c 1.979,2.396 2.146,2.563 0.167,0.167 10 false *d 1.51,2.635 1.677,2.802 0.167,0.167 10 false *e 0.26,0.24 0.427,0.406 0.167,0.167 10 false *f 2.094,3.104 2.427,3.271 0.333,0.167 10 false MR 2.271,4.219 2.521,4.385 0.25,0.167 10 false MF
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Battery Connection Condition Specified Condition
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 8 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 3 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 8 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 8 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 3 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 8 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 8 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly RH.



Hide 87910 2.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH (w/ Memory)

a.

Check the operation of the mirror surface.

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B294037
1.271,2.5 0.906,2.5 false 1.427,2.74 1.427,3.167 1.427,3.167 1.698,3.167 false 1.302,2.74 1.302,3.167 1.302,3.167 1.042,3.167 false 1.74,3.083 2.188,3.292 0.448,0.208 10 false M+ 0.198,0.156 0.531,0.385 0.333,0.229 10 false *a 0.75,3.083 1.167,3.281 0.417,0.198 10 false MH 0.625,2.417 0.99,2.646 0.365,0.229 10 false MV
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Apply battery voltage and check the operation of the mirror surface.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 1 (MV)
Battery negative (-) → Terminal 10 (M+)
Turns upward
Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 1 (MV)
Turns downward
Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 10 (M+)
Turns left
Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 9 (MH)
Turns right


If the result is not as specified, replace the outer rear view mirror assembly RH.



b.

Check the operation of the mirror heater. (w/ Mirror Heater)

i.
B295685
1.698,2.729 1.698,3.156 1.698,3.156 1.271,3.156 false 1.271,1.74 1.688,1.74 1.688,1.74 1.688,2.427 false 0.167,0.094 0.448,0.302 0.281,0.208 10 false *a 1.146,3.052 1.26,3.281 0.115,0.229 10 false - 1.104,1.646 1.26,1.865 0.156,0.219 10 false +
*a Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (+) - 12 (-) 25°C (77°F) 3.57 to 4.83 Ω


If the result is not as specified, replace the outer rear view mirror assembly RH.


iii.

Connect a cable from the positive (+) battery terminal to terminal 4 and the negative (-) battery terminal to terminal 12, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly RH.



c.

Check the operation of the retractable mirror. (w/ Retract Mirror)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.
B295612
1.479,3.917 1.479,4.26 1.479,4.26 0.781,4.26 false 1.479,3.635 1.479,3.219 1.479,3.219 0.781,3.219 false 0.177,0.135 0.51,0.354 0.333,0.219 10 false *f 2.469,1.896 2.76,2.208 0.292,0.313 10 false *c 1.5,2.563 1.792,2.833 0.292,0.271 10 false *e 0.51,3.135 0.906,3.385 0.396,0.25 10 false MR 0.531,4.177 0.927,4.375 0.396,0.198 10 false MF 2.156,0.094 2.479,0.313 0.323,0.219 10 false *a 2.594,1 2.896,1.24 0.302,0.24 10 false *b 2.021,2.281 2.292,2.563 0.271,0.281 10 false *d
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly RH)


Disconnect the outer rear view mirror assembly RH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Battery Connection Condition Specified Condition
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly RH.



Hide 87940 3.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/o Memory)

a.

Check the operation of the mirror surface.

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B357254
1.302,3.156 1.469,3.156 1.469,3.156 1.469,2.677 false 1.75,3.156 1.583,3.156 1.583,3.156 1.583,2.677 false 1.635,1.906 1.469,1.906 1.469,1.906 1.469,2.448 false 0.24,0.135 0.573,0.49 0.333,0.354 10 false *a 1.698,1.823 1.948,1.99 0.25,0.167 10 false MV 1.802,3.073 2.052,3.24 0.25,0.167 10 false M+ 1.042,3.063 1.292,3.229 0.25,0.167 10 false MH
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply battery voltage and check the operation of the mirror surface.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 1 (MV)
Battery negative (-) → Terminal 7 (M+)
Turns upward
Battery positive (+) → Terminal 7 (M+)
Battery negative (-) → Terminal 1 (MV)
Turns downward
Battery positive (+) → Terminal 6 (MH)
Battery negative (-) → Terminal 7 (M+)
Turns right
Battery positive (+) → Terminal 7 (M+)
Battery negative (-) → Terminal 6 (MH)
Turns left


If the result is not as specified, replace the outer rear view mirror assembly LH.



b.

Check the operation of the mirror heater. (w/ Mirror Heater)

i.
B364134
1.573,2.458 1.573,1.854 1.573,1.854 1.958,1.854 false 1.844,2.698 1.844,3.135 1.844,3.135 2.146,3.135 false 0.177,0.125 0.49,0.323 0.313,0.198 10 false *a 2.01,1.76 2.469,1.969 0.458,0.208 10 false + 2.208,3.073 2.667,3.281 0.458,0.208 10 false E
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (+) - 9 (E) 25°C (77°F) 3.57 to 4.83 Ω


If the result is not as specified, replace the outer rear view mirror assembly LH.


iii.

Connect a cable from the positive (+) battery terminal to terminal 2 and the negative (-) battery terminal to terminal 9, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.



c.

Check the operation of the retractable mirror. (w/ Retract Mirror)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.
B357255
2.01,3.083 1.75,3.083 1.75,3.083 1.75,3.677 false 2.042,4.417 1.76,4.417 1.76,4.417 1.76,3.927 false 1.177,0.146 1.344,0.313 0.167,0.167 10 false *a 0.719,1.146 0.885,1.313 0.167,0.167 10 false *b 1.323,2.365 1.49,2.531 0.167,0.167 10 false *d 0.854,1.969 1.021,2.135 0.167,0.167 10 false *c 1.823,2.625 1.99,2.792 0.167,0.167 10 false *e 0.24,0.188 0.406,0.354 0.167,0.167 10 false *f 2.063,3 2.396,3.167 0.333,0.167 10 false MR 2.094,4.333 2.344,4.5 0.25,0.167 10 false MF
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Battery Connection Condition Specified Condition
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 8 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 3 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 8 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 8 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 3 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 8 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 8 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 8 (MF)
Battery negative (-) → Terminal 3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly LH.



Hide 87940 4.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH (w/ Memory)

a.

Check the operation of the mirror surface.

NOTICE:

If the mirror surface is fully turned to the right, left, upward or downward position, the motor slips and produces a clicking noise. This is not a malfunction.


i.
B294038
1.26,2.479 0.802,2.479 false 1.438,2.729 1.438,3.198 1.438,3.198 1.615,3.198 false 1.313,2.729 1.313,3.198 1.313,3.198 1.125,3.198 false 0.177,0.115 0.385,0.333 0.208,0.219 10 false *a 0.49,2.406 0.729,2.552 0.24,0.146 10 false MV 1.656,3.115 1.875,3.26 0.219,0.146 10 false M+ 0.813,3.115 1.052,3.26 0.24,0.146 10 false MH
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Apply battery voltage and check the operation of the mirror surface.

OK:
Battery Connection Specified Condition
Battery positive (+) → Terminal 1 (MV)
Battery negative (-) → Terminal 10 (M+)
Turns upward
Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 1 (MV)
Turns downward
Battery positive (+) → Terminal 9 (MH)
Battery negative (-) → Terminal 10 (M+)
Turns right
Battery positive (+) → Terminal 10 (M+)
Battery negative (-) → Terminal 9 (MH)
Turns left


If the result is not as specified, replace the outer rear view mirror assembly LH.



b.

Check the operation of the mirror heater. (w/ Mirror Heater)

i.
B295686
1.698,2.729 1.698,3.135 1.698,3.135 1.01,3.135 false 1.01,1.833 1.698,1.833 1.698,1.833 1.698,2.406 false 0.188,0.146 0.448,0.365 0.26,0.219 10 false *a 0.844,3.031 0.99,3.271 0.146,0.24 10 false - 0.854,1.74 0.969,1.948 0.115,0.208 10 false +
*a Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (+) - 12 (-) 25°C (77°F) 3.57 to 4.83 Ω


If the result is not as specified, replace the outer rear view mirror assembly LH.


iii.

Connect a cable from the positive (+) battery terminal to terminal 4 and the negative (-) battery terminal to terminal 12, then check that the mirror becomes warm.

HINT:

It takes a short time for the mirror to become warm.


OK:

Mirror becomes warm.


If the result is not as specified, replace the outer rear view mirror assembly LH.



c.

Check the operation of the retractable mirror. (w/ Retract Mirror)

NOTICE:
·

Disconnect and reconnect the battery between each mirror position check.

·

The mirror position cannot be changed manually when the battery is connected. To change the mirror position manually, the battery must be disconnected first.

·

If the motor is kept energized, even after each mirror position check, it may lead to a motor malfunction. Make sure to disconnect the battery immediately after performing each mirror position check.



i.
B295613
1.542,3.813 1.542,4.26 1.542,4.26 1.031,4.26 false 1.542,3.51 1.542,3.083 1.542,3.083 1.031,3.083 false 0.177,0.115 0.521,0.438 0.344,0.323 10 false *f 0.917,1.927 1.198,2.177 0.281,0.25 10 false *c 1.927,2.604 2.229,2.833 0.302,0.229 10 false *e 1.219,0.094 1.458,0.323 0.24,0.229 10 false *a 0.792,0.938 1.042,1.167 0.25,0.229 10 false *b 1.365,2.333 1.677,2.563 0.313,0.229 10 false *d 0.76,3 1.073,3.198 0.313,0.198 10 false MR 0.792,4.188 1.125,4.385 0.333,0.198 10 false MF
*a (A) Forward position
*b (B)
*c (C) Driving position
*d (D)
*e (E) Retracted position
*f Component without harness connected
(Outer Rear View Mirror Assembly LH)


Disconnect the outer rear view mirror assembly LH connector.


ii.

For each position: Disconnect the battery, set the mirror position by hand, connect the battery, and check the retractable mirror movement.

OK:
Battery Connection Condition Specified Condition
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Forward position (A) Moves from (A) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Forward position (A) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Position between forward position (A) and driving position (C) Moves from (B) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between forward position (A) and driving position (C) Moves from (B) to (A)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Driving position (C) Moves from (C) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Driving position (C) Does not move
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Position between driving position (C) and retracted position (E) Moves from (D) to (E)
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Position between driving position (C) and retracted position (E) Moves from (D) to (C)
Battery positive (+) → Terminal 3 (MR)
Battery negative (-) → Terminal 11 (MF)
Retracted position (E) Does not move
Battery positive (+) → Terminal 11 (MF)
Battery negative (-) → Terminal 3 (MR)
Retracted position (E) Moves from (E) to (C)


If the result is not as specified, replace the outer rear view mirror assembly LH.