Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY
RM3160E _55 Steering _019698 STEERING COLUMN _0101108 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

Do not drop the power steering ECU assembly and power steering motor assembly, strike it with tools or subject it to impacts.

·

If the power steering ECU assembly and power steering motor assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness of the electric power steering column sub-assembly.

·

Do not allow any moisture to come into contact with the power steering ECU assembly and power steering motor assembly.

·

Do not loosen any bolts not mentioned in the procedure.



PROCEDURE

Hide 45020A 1.REMOVE STEERING LOCK ACTUATOR ASSEMBLY (w/ Smart Entry and Start System)

a.

Secure the steering column assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise, as the steering column assembly may become deformed.



b.

Using a drill, drill a hole in the 2 steering lock set bolts and insert a screw extractor.


c.
C291601

Using the screw extractor, remove the 2 steering lock set bolts and steering lock actuator assembly.


Hide 2.REMOVE UPPER STEERING COLUMN BRACKET WITH SWITCH ASSEMBLY (w/o Smart Entry and Start System)

HINT:

Perform the same procedure as for the steering lock actuator assembly.


Hide 45220 3.REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C291602
0.594,1.677 0.958,1.229 0.958,1.229 0.646,1.677 true 0.948,1.083 1.26,1.24 0.313,0.156 10 false *a
*a Matchmark


Remove the bolt and slide the steering intermediate shaft assembly.

NOTICE:

Do not separate the steering intermediate shaft assembly from the steering column assembly.



b.

Put matchmarks on the steering intermediate shaft assembly and the steering column assembly.


c.

Remove the steering intermediate shaft assembly from the steering column assembly.


Hide 8965A 4.REMOVE POWER STEERING ECU PROTECTOR

a.
C291604

Disengage the 2 claws to remove the power steering ECU protector from the power steering ECU assembly.


Hide F1901 5.REMOVE ECU WIRE SUB-ASSEMBLY

a.
C291605

Disconnect the 2 connectors from the power steering ECU assembly.


b.
C291606

Disengage the 2 wire harness clamps to remove the ECU wire sub-assembly.


Hide 6.REMOVE POWER STEERING ECU WITH MOTOR ASSEMBLY

a.
C291608

Disconnect the 2 connectors from the power steering ECU assembly.


b.
C291607

Remove the tape.


c.
C291609

Remove the 2 bolts and power steering ECU with motor assembly from the electric power steering column sub-assembly.


d.
C291610

Remove the O-ring from the power steering ECU with motor assembly.


Hide 80960 7.REMOVE POWER STEERING MOTOR ASSEMBLY

a.
C295434

Disengage the 4 claws to remove the No. 2 power steering ECU protector.


b.
C295435

Remove the 3 terminal bolts, 2 bolts and power steering motor assembly from the power steering ECU assembly.


Hide 89782 8.REMOVE TRANSPONDER KEY COIL (w/o Smart Entry and Start System)

a.
C292553

Disengage the 2 claws and remove the transponder key coil.


Hide 84450 9.REMOVE IGNITION OR STARTER SWITCH ASSEMBLY (w/o Smart Entry and Start System)

a.
C292554

Remove the 2 screws and ignition or starter switch assembly from the upper steering column bracket assembly.


Hide 85432 10.REMOVE KEY INTERLOCK SOLENOID (w/o Smart Entry and Start System)

a.
C292555

Remove the screw.


b.

Disengage the claw to remove the key interlock solenoid from the upper steering column bracket assembly.


Hide 11.REMOVE IGNITION SWITCH LOCK CYLINDER ASSEMBLY (w/o Smart Entry and Start System)

a.
C292556
2.125,0.573 2.583,0.771 0.458,0.198 10 false ACC 2.25,1.052 2.708,1.25 0.458,0.198 10 false LOCK
V100135

Push
V100136

Pull


Turn the ignition switch to ACC.


b.

Insert the tip of a screwdriver into the hole in the upper steering column bracket assembly, as shown in the illustration, and pull the ignition switch lock cylinder assembly.


c.
C292557
1.365,0.688 1.438,0.396 1.438,0.396 1.573,0.396 true 3.063,0.927 2.927,0.927 2.927,0.927 2.927,0.74 true 1.615,0.313 1.927,0.469 0.313,0.156 10 false *a 3.104,0.844 3.417,1 0.313,0.156 10 false *a
*a Claw
V100135

Tilt
V100136

Pull out


Insert the tip of a screwdriver into the hole in the upper steering column bracket assembly and tilt it downward, as shown in the illustration, to disengage the claw on the ignition switch lock cylinder assembly. Then pull out the ignition switch lock cylinder assembly.


Hide 84052 12.REMOVE UN-LOCK WARNING SWITCH ASSEMBLY (w/o Smart Entry and Start System)

a.
C292559
1.333,2.667 1.688,2.667 true 1.708,2.583 2.021,2.74 0.313,0.156 10 false *a
*a Center Part


Remove the un-lock warning switch assembly by pushing up the center part and releasing the 2 claws.

HINT:

Slide the un-lock warning switch in the direction shown by the arrow in the illustration to remove it.