Home › Steering › STEERING COLUMN › STEERING PAD SWITCH › 2013.12–2016.11
RM3160E _55 Steering _019698 STEERING COLUMN _0101110 STEERING PAD SWITCH G

STEERING COLUMN  STEERING PAD SWITCH  INSPECTION  


PROCEDURE

Hide 84250A 1.INSPECT STEERING PAD SWITCH ASSEMBLY (w/ Navigation System)

a.

Measure the resistance according to the value(s) in the table below.

E284056
1.5,0.365 1.823,0.583 0.323,0.219 5.375,0.417 5.698,0.635 0.323,0.219 2,0.563 2.156,0.427 false 4.198,0.313 4.479,0.469 false 4.396,0.188 4.563,0.479 false 4.771,0.198 4.635,0.479 false 4.99,0.313 4.75,0.479 false 4.219,0.667 4.385,0.583 false 4.365,0.813 4.479,0.583 false 4.74,0.844 4.635,0.583 false 4.979,0.771 4.771,0.594 false 4.771,1.885 4.708,1.333 false 4.938,1.729 5.073,1.281 false 4.938,1.896 5.51,1.281 false 5.292,1.771 5.552,1.771 false 5.26,2.01 5.521,2.01 false 5.073,1.906 5.51,2.354 false 5.073,2.365 5.177,2.615 false 4.917,2.063 4.906,2.813 false 2.302,1.771 2.49,1.177 false 2.094,1.719 2.052,1.188 false 1.885,1.781 1.635,1.49 false 1.885,2.052 1.573,2.115 false 2.063,2.063 1.458,2.292 false 1.958,2.354 1.802,2.635 false 2.198,2.375 2.146,2.75 false 2.333,2.052 2.323,2.938 false 0.219,0.167 0.531,0.323 0.313,0.156 10 false *a 1.479,1.333 1.792,1.49 0.313,0.156 10 false *b 1.385,2.031 1.698,2.188 0.313,0.156 10 false *c 1.958,1 2.271,1.156 0.313,0.156 10 false *d 1.25,2.24 1.563,2.396 0.313,0.156 10 false *e 2.479,0.979 2.792,1.135 0.313,0.156 10 false *f 1.688,2.604 1.948,2.885 0.26,0.281 10 false *g 2.063,2.76 2.375,2.917 0.313,0.156 10 false *h 2.271,3 2.583,3.156 0.313,0.156 10 false *i 5.063,1.063 5.313,1.313 0.25,0.25 10 false *j 4.865,2.844 5.177,3 0.313,0.156 10 false *k 4.646,1.125 4.958,1.281 0.313,0.156 10 false *l 5.563,2.385 5.875,2.542 0.313,0.156 10 false *m 5.552,1.135 5.865,1.292 0.313,0.156 10 false *n 5.594,1.688 5.906,1.844 0.313,0.156 10 false *o 5.125,2.635 5.542,2.875 0.417,0.24 10 false *p*A 5.563,1.917 5.792,2.156 0.229,0.24 10 false *q 3.896,0.198 4.354,0.396 0.458,0.198 10 false +DP 4.208,0.021 4.667,0.219 0.458,0.198 10 false +DP2 4.667,0.021 5.292,0.26 0.625,0.24 10 false DIST*A 5.021,0.229 5.479,0.427 0.458,0.198 10 false HO 3.802,0.677 4.365,0.865 0.563,0.188 10 false ECC*A 4.208,0.844 4.667,1.042 0.458,0.198 10 false EAU 4.594,0.875 5.052,1.073 0.458,0.198 10 false AU2 4.927,0.792 5.385,0.99 0.458,0.198 10 false AU1 1.917,0.594 2.385,0.792 0.469,0.198 10 false HO 1.625,0.396 2.094,0.594 0.469,0.198 10 false A 5.458,0.438 5.927,0.635 0.469,0.198 10 false z4
*A w/ Dynamic Radar Cruise Control System - -
*a Component without harness connected
(Steering Pad Switch Assembly)
*b Volume+
*c Volume- *d Seek+
*e Seek- *f MODE/HOLD
*g Off hook *h On hook
*i Voice *j Up
*k Down *l Left
*m Right *n Enter
*o Back *p Distance Control
*q Top - -


Standard Resistance:
Tester Connection Condition Specified Condition
z4-11 (AU1) - z4-8 (EAU) No switch pushed 95 to 105 kΩ
SEEK+ switch pushed Below 2.5 Ω
SEEK- switch pushed 313 to 345 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume- switch pushed 2955 to 3265 Ω
z4-10 (AU2) - z4-8 (EAU) No switch pushed 95 to 105 kΩ
MODE/HOLD switch pushed Below 2.5 Ω
On hook switch pushed 313 to 345 Ω
Off hook switch pushed 950 to 1050 Ω
Voice switch pushed 2955 to 3265 Ω
z4-3 (+DP2) - z4-8 (EAU) No switch pushed 95 to 105 kΩ
Left switch pushed Below 2.5 Ω
Up switch pushed 313 to 345 Ω
Down switch pushed 950 to 1050 Ω
Right switch pushed 2955 to 3265 Ω
z4-2 (+DP) - z4-8 (EAU) No switch pushed 95 to 105 kΩ
Enter switch pushed Below 2.5 Ω
Top switch pushed 313 to 345 Ω
Back switch pushed 950 to 1050 Ω
z4-4 (DIST) - z4-7 (ECC)*1 No switch pushed 1 MΩ or higher
Distance control switch pushed Below 2.5 Ω
z4-1 (HO) - A-1 (HO) Always Below 2.5 Ω


*1: w/ Dynamic Radar Cruise Control System


HINT:

If the result is not as specified, replace the steering pad switch assembly.



b.

Check the illumination.

E284057
4.219,0.833 4.49,0.573 false 4.042,0.188 4.417,0.49 false 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 3.719,0.094 4.219,0.302 0.5,0.208 10 false IL+2 4.063,0.885 4.563,1.094 0.5,0.208 10 false EAU
*a Component without harness connected
(Steering Pad Switch Assembly)
- -


i.

Connect a battery positive (+) lead to terminal 1 (IL+2) and a negative (-) lead to terminal 8 (EAU) of the steering pad switch assembly connector.


ii.

Check that the switch illumination comes on.

OK:

Steering pad switch illumination comes on.


HINT:

If the result is not as specified, replace the steering pad switch assembly.




Hide 84250A 2.INSPECT STEERING PAD SWITCH ASSEMBLY (w/o Navigation System)

a.

Measure the resistance according to the value(s) in the table below.

E284080
1.594,0.302 1.885,0.51 0.292,0.208 5.198,0.438 5.49,0.646 0.292,0.208 2.083,0.573 2.156,0.438 false 4.75,0.469 5.042,0.313 false 4.75,0.594 4.958,0.74 false 4.656,0.604 4.76,0.823 false 4.583,0.604 4.521,0.917 false 4.5,0.604 4.313,0.781 false 4.229,0.302 4.469,0.458 false 4.729,1.344 4.771,1.875 false 5.031,1.281 4.927,1.719 false 5.406,1.354 4.927,1.885 false 5.292,1.781 5.583,1.781 false 5.094,1.896 5.583,2.146 false 5.083,2.375 5.479,2.604 false 4.927,2.073 4.927,2.74 false 2.469,1.229 2.292,1.75 false 2.052,1.177 2.104,1.719 false 1.625,1.385 1.875,1.75 false 1.854,2.01 1.552,2.104 false 2.042,2.073 1.5,2.313 false 1.979,2.365 1.792,2.625 false 2.188,2.375 2.094,2.698 false 2.333,2.083 2.333,2.875 false 1.708,0.323 2.021,0.479 0.313,0.156 10 false A 0.292,0.25 0.604,0.406 0.313,0.156 10 false *a 1.448,1.229 1.677,1.396 0.229,0.167 10 false *b 1.396,2.031 1.708,2.188 0.313,0.156 10 false *c 1.969,1.01 2.177,1.229 0.208,0.219 10 false *d 1.323,2.25 1.635,2.406 0.313,0.156 10 false *e 2.469,1.031 2.781,1.188 0.313,0.156 10 false *f 1.646,2.615 1.979,2.865 0.333,0.25 10 false *g 1.99,2.719 2.302,2.875 0.313,0.156 10 false *h 2.271,2.948 2.583,3.104 0.313,0.156 10 false *i 5,1.073 5.25,1.292 0.25,0.219 10 false *j 4.865,2.802 5.177,2.958 0.313,0.156 10 false *k 4.646,1.177 4.958,1.333 0.313,0.156 10 false *l 5.615,2.156 5.927,2.313 0.313,0.156 10 false *m 5.375,1.188 5.688,1.344 0.313,0.156 10 false *n 5.635,1.688 5.948,1.844 0.313,0.156 10 false *o 5.51,2.573 5.823,2.729 0.313,0.156 10 false *p 5.281,0.458 5.594,0.615 0.313,0.156 10 false z4 1.979,0.615 2.292,0.771 0.313,0.156 10 false HO 5,0.74 5.448,0.906 0.448,0.167 10 false AU1 5.094,0.198 5.406,0.354 0.313,0.156 10 false HO 4.708,0.854 5.156,1.021 0.448,0.167 10 false AU2 4.375,0.969 4.823,1.135 0.448,0.167 10 false AU3 4.073,0.813 4.521,0.979 0.448,0.167 10 false EAU 3.979,0.177 4.375,0.365 0.396,0.188 10 false +DP
*a Component without harness connected
(Steering Pad Switch Assembly)
*b Volume+
*c Volume- *d Seek+
*e Seek- *f MODE/HOLD
*g Off hook *h On hook
*i Voice *j Up
*k Down *l Left
*m Right *n Enter
*o Back *p DISP


Standard Resistance:
Tester Connection Condition Specified Condition
z4-11 (AU1) - z4-8 (EAU) No switch pushed 95 to 105 kΩ
SEEK+ switch pushed Below 2.5 Ω
SEEK- switch pushed 313 to 345 Ω
Volume+ switch pushed 950 to 1050 Ω
Volume- switch pushed 2955 to 3265 Ω
Up switch pushed Below 2.5 Ω
Down switch pushed 313 to 345 Ω
z4-10 (AU2) - z4-8 (EAU) No switch pushed 95 to 105 kΩ
MODE/HOLD switch pushed Below 2.5 Ω
On hook switch pushed 313 to 345 Ω
Off hook switch pushed 950 to 1050 Ω
Voice switch pushed 2955 to 3265 Ω
z4-9 (AU3) - z4-8 (EAU) No switch pushed 95 to 105 kΩ
Enter switch pushed Below 2.5 Ω
Back switch pushed 313 to 345 Ω
Right switch pushed 950 to 1050 Ω
Left switch pushed 2955 to 3265 Ω
z4-2 (+DP) - z4-8 (EAU) No switch pushed 95 to 105 kΩ
DISP switch pushed Below 2.5 Ω
z4-1 (HO) - A-1 (HO) Always Below 2.5 Ω


HINT:

If the result is not as specified, replace the steering pad switch assembly.



b.

Check the illumination.

E284079C01
4.406,0.479 4.104,0.198 false 4.313,0.823 4.49,0.573 false 0.25,0.208 0.563,0.365 0.313,0.156 10 false *a 3.938,0.031 4.302,0.25 0.365,0.219 10 false IL+2 4.156,0.854 4.521,1.073 0.365,0.219 10 false EAU
*a Component without harness connected
(Steering Pad Switch Assembly)
- -


i.

Connect a battery positive (+) lead to terminal 1 (IL+2) and a negative (-) lead to terminal 8 (EAU) of the steering pad switch assembly connector.


ii.

Check that the switch illumination comes on.

OK:

Steering pad switch illumination comes on.


HINT:

If the result is not as specified, replace the steering pad switch assembly.