Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type)
RM3160E _56 Audio / Visual / Telematics _019701 NAVIGATION / MULTI INFO DISPLAY _0101135 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E287097E06
1.021,0.792 2.854,0.99 1.833,0.198 10 false from Battery 0.802,1.573 2.635,1.771 1.833,0.198 10 false from ACC Relay 0.49,2.375 2.323,2.573 1.833,0.198 10 false from IG1 NO. 3 Relay 3.469,0.969 5.302,1.167 1.833,0.198 10 false RADIO 3.375,1.75 5.208,1.948 1.833,0.198 10 false ECU-ACC 3.354,2.573 5.073,2.771 1.719,0.198 10 false IG1 NO. 3 5.323,3.625 7.031,4.135 1.708,0.51 10 false Radio and Display Receiver Assembly 5.448,0.802 5.76,1 0.313,0.198 10 false F69 5.458,1.594 5.771,1.792 0.313,0.198 10 false F69 5.438,2.375 5.75,2.573 0.313,0.198 10 false F71 5.448,3.167 5.76,3.365 0.313,0.198 10 false F69 5.521,2.99 5.833,3.188 0.313,0.198 10 false 7 5.51,2.188 5.823,2.385 0.313,0.198 10 false 1 5.51,1.385 5.823,1.583 0.313,0.198 10 false 3 5.51,0.604 5.823,0.802 0.313,0.198 10 false 4 5.802,0.792 6.26,1.021 0.458,0.229 10 false +B1 5.802,1.573 6.26,1.802 0.458,0.229 10 false ACC1 5.813,2.375 6.271,2.604 0.458,0.229 10 false IG 5.813,3.167 6.271,3.396 0.458,0.229 10 false GND1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the F69 and F71 radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F69-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F69-4 (+B1) - F69-7 (GND1) Always 11 to 14 V
F69-3 (ACC1) - F69-7 (GND1) Engine switch on (ACC) 11 to 14 V
F71-1 (IG) - F69-7 (GND1) Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR