Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type)
RM3160E _56 Audio / Visual / Telematics _019701 NAVIGATION / MULTI INFO DISPLAY _0101135 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier  


DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Due to this, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E262317E33
1.25,1.042 1.719,1.198 0.469,0.156 10 false MUTE 5.552,1.052 5.969,1.219 0.417,0.167 10 false MUT1 1.771,0.906 2.01,1.135 0.24,0.229 10 false 1 5.281,0.917 5.542,1.125 0.26,0.208 10 false 16 0.583,1.896 0.875,2.052 0.292,0.156 10 false F76 5.24,2.083 6.948,2.49 1.708,0.406 10 false Radio and Display Receiver Assembly 5.24,1.917 5.615,2.104 0.375,0.188 10 false F71 0.573,2.063 1.844,2.563 1.271,0.5 10 false Stereo Component Amplifier Assembly

PROCEDURE

1.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
E225824C16
1.49,0.792 1.948,1.073 0.458,0.281 2.396,1.885 2.865,2.385 false 0.208,0.167 0.365,0.333 0.156,0.167 10 false *a 1.615,0.854 1.948,1.01 0.333,0.156 10 false F76 2.698,2.417 3.125,2.583 0.427,0.167 10 false MUTE
*a Component with harness connected
(Stereo Component Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F76-1 (MUTE) - Body ground Engine switch on (ACC)
Audio system playing
→ Audio system changing modes
2.0 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the F71 radio and display receiver assembly connector.


b.

Disconnect the F76 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-16 (MUT1) - F76-1 (MUTE) Always Below 1 Ω
F71-16 (MUT1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Disconnect the F71 radio and display receiver assembly connector.


b.
E265411C07
1.5,0.5 1.938,0.781 0.438,0.281 0.854,2.542 0.979,2.094 false 0.208,0.25 0.521,0.448 0.313,0.198 10 false *a 1.604,0.563 1.958,0.771 0.354,0.208 10 false F71 0.688,2.594 1.333,2.854 0.646,0.26 10 false MUT1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F71-16 (MUT1) - Body ground Engine switch on (ACC)
Audio system playing
2.0 V or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY