Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › 2013.12–2016.11
RM3160E _56 Audio / Visual / Telematics _019701 NAVIGATION / MULTI INFO DISPLAY _0101135 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  AVC-LAN Circuit  


DESCRIPTION

Each unit of the navigation system connected to the AVC-LAN (communication bus) transfers switch signals through the AVC-LAN.

If a short to +B or short to ground occurs in the AVC-LAN, the navigation system will not function normally because communication is not possible.

WIRING DIAGRAM

E277861
0.708,1.781 2.458,2.135 1.75,0.354 10 false Stereo Component Amplifier Assembly 5.031,1.854 6.729,2.229 1.698,0.375 10 false Radio and Display Receiver Assembly 0.938,2.396 2.938,2.615 2,0.219 10 false : AVC-LAN Communication Line 1.813,0.406 2.427,0.604 0.615,0.198 10 false TX+ 1.844,1.188 2.458,1.385 0.615,0.198 10 false TX- 0.719,1.604 1.333,1.802 0.615,0.198 10 false F76 5.031,1.688 5.646,1.885 0.615,0.198 10 false F71 5.083,0.385 5.698,0.583 0.615,0.198 10 false TX1+ 5.094,1.188 5.708,1.385 0.615,0.198 10 false TX1- 4.906,0.271 5.521,0.469 0.615,0.198 10 false 7 4.906,1.052 5.521,1.25 0.615,0.198 10 false 8 2.146,0.271 2.76,0.469 0.615,0.198 10 false 8 2.156,1.052 2.771,1.25 0.615,0.198 10 false 7

CAUTION / NOTICE / HINT

HINT:

The radio and display receiver assembly is the master unit.


PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Remove the radio and display receiver assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.
E221758
1.365,1.729 1.615,1.229 false 2.083,1.729 1.802,1.219 false 0.135,0.083 0.552,0.479 0.417,0.396 10 false *a 1.208,1.771 1.583,2.021 0.375,0.25 10 false TX1- 1.99,1.771 2.521,2 0.531,0.229 10 false TX1+
*a Component without harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (TX1+) - 8 (TX1-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the F71 radio and display receiver assembly connector.


b.

Disconnect the F76 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-7 (TX1+) - F76-8 (TX+) Always Below 1 Ω
F71-8 (TX1-) - F76-7 (TX-) Always Below 1 Ω
F71-7 (TX1+) - Body ground Always 10 kΩ or higher
F71-8 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal operation.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal operation, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal operation.



Result:
Proceed to
OK
NG



OK

REPLACE MALFUNCTIONING PARTS

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY