Home › Vehicle Exterior › WIPER / WASHER › WIPER SWITCH › 2013.12–2015.11
RM3160E _59 Vehicle Exterior _019721 WIPER / WASHER _0101300 WIPER SWITCH G

WIPER / WASHER  WIPER SWITCH  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 84650 1.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (w/ Auto Wiper System)

a.

Check the front washer operation.

i.
E257039C22
0.417,0.99 0.76,1.208 0.344,0.219 2.615,1 2.969,1.219 0.354,0.219 1.25,1.052 0.823,0.49 false 2.688,1.729 2.354,1.354 false 0.083,0.125 0.396,0.323 0.313,0.198 10 false *a 0.49,1.021 0.802,1.219 0.313,0.198 10 false F64 2.698,1.031 3.01,1.229 0.313,0.198 10 false F65 0.677,0.302 0.99,0.5 0.313,0.198 10 false +1 2.677,1.771 2.99,1.969 0.313,0.198 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal F64-3 (+1) and a negative (-) lead to terminal F65-4 (EW).


ii.

Turn the ignition switch to ON.


iii.

Turn the washer switch on and off, and check the voltage between terminals F64-3 (+1) and F65-4 (EW).

OK:

Voltage changes as shown in the illustration.


E226602E41
4.094,1.333 4.021,1.5 false 4.76,1.333 4.844,1.51 false 0.573,0.823 2.885,1.344 2.313,0.521 10 false Voltage between terminals F64-3 (+1) and F65-4 (EW): 1.677,0.208 2.667,0.542 0.99,0.333 10 false Washer Switch: 2.49,1.5 4.49,1.75 2,0.25 10 false Approximately 0.5 seconds 4.573,1.49 6.51,1.75 1.938,0.26 10 false Approximately 2.2 seconds 2.958,0.792 3.792,1.156 0.833,0.365 10 false 11 to 14 V 3.375,1.135 3.833,1.542 0.458,0.406 10 false 0 V 3.302,0.438 3.813,0.833 0.51,0.396 10 false Off 3.344,0.219 3.74,0.552 0.396,0.333 10 false On

If the result is not as specified, replace the windshield wiper switch assembly.



Hide 84650 2.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (w/o Auto Wiper System)

a.

Check the front wiper intermittent operation (for LHD).

i.
E257039C23
0.417,0.99 0.76,1.208 0.344,0.219 2.615,1 2.958,1.219 0.344,0.219 1.25,1.052 0.823,0.49 false 2.688,1.729 2.354,1.354 false 0.083,0.125 0.396,0.323 0.313,0.198 10 false *a 0.49,1.021 0.802,1.219 0.313,0.198 10 false F64 2.688,1.031 3,1.229 0.313,0.198 10 false F65 0.677,0.302 0.99,0.5 0.313,0.198 10 false +1 2.677,1.771 2.99,1.969 0.313,0.198 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal F64-3 (+1) and a negative (-) lead to terminal F65-4 (EW).


ii.

Turn the wiper switch to the INT position.


iii.

Operate the intermittent wiper and check the voltage between terminals F64-3 (+1) and F65-4 (EW).

OK:

Voltage changes as shown in the illustration.


E136493E42
2.625,0.104 3.104,0.271 0.479,0.167 10 false FAST: 1.927,0.385 2.615,0.563 0.688,0.177 10 false 11 to 14 V 2.344,0.885 2.594,1.063 0.25,0.177 10 false 0 V 3.177,1.385 3.531,1.563 0.354,0.177 10 false Start 0.073,0.5 1.865,1.177 1.792,0.677 10 false Voltage between terminals F64-3 (+1) and F65-4 (EW): 0.771,1.375 1.854,1.552 1.083,0.177 10 false Wiper Operation: 3.354,1 4.542,1.198 1.188,0.198 10 false 1.6 +/- 1 second 5.792,1 7.021,1.198 1.229,0.198 10 false 10.7 +/- 5 seconds 2.729,1.385 3.083,1.563 0.354,0.177 10 false Stop 5.583,1.385 5.938,1.563 0.354,0.177 10 false Start 4.792,1.385 5.146,1.563 0.354,0.177 10 false Stop 4.438,0.104 4.979,0.302 0.542,0.198 10 false SLOW:

If the result is not as specified, replace the windshield wiper switch assembly.



b.

Check the front washer operation (for LHD).

i.
E257039C24
0.417,0.99 0.76,1.198 0.344,0.208 2.615,1 2.969,1.219 0.354,0.219 1.24,1.052 0.823,0.49 false 2.688,1.729 2.354,1.354 false 0.083,0.125 0.396,0.323 0.313,0.198 10 false *a 0.49,1.021 0.802,1.219 0.313,0.198 10 false F64 2.688,1.031 3,1.229 0.313,0.198 10 false F65 0.677,0.302 0.99,0.5 0.313,0.198 10 false +1 2.677,1.771 2.99,1.969 0.313,0.198 10 false EW
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal F64-3 (+1) and a negative (-) lead to terminal F65-4 (EW).


ii.

Turn the ignition switch to ON.


iii.

Turn the washer switch on and off, and check the voltage between terminals F64-3 (+1) and F65-4 (EW).

OK:

Voltage changes as shown in the following illustration.


E226602E42
4.104,1.323 4.021,1.521 false 4.74,1.333 4.865,1.51 false 0.99,0.885 2.719,1.219 1.729,0.333 10 false Voltage between terminals F64-3 (+1) and F65-4 (EW): 1.698,0.281 2.958,0.552 1.26,0.271 10 false Washer Switch: 2.604,1.531 4.354,1.771 1.75,0.24 10 false Approximately 0.5 seconds 4.708,1.531 6.708,1.729 2,0.198 10 false Approximately 2.2 seconds 2.948,0.823 3.708,1 0.76,0.177 10 false 11 to 14 V 3.365,1.167 3.74,1.313 0.375,0.146 10 false 0 V 3.292,0.479 3.688,0.635 0.396,0.156 10 false Off 3.354,0.188 3.729,0.365 0.375,0.177 10 false On

If the result is not as specified, replace the windshield wiper switch assembly.



c.

Check the front wiper intermittent operation (for RHD).

i.
E239385C42
0.271,1.042 0.656,1.313 0.385,0.271 2.813,1.042 3.208,1.313 0.396,0.271 2.219,1.104 2.406,0.583 false 0.979,1.385 0.792,1.698 false 0.365,1.094 0.646,1.271 0.281,0.177 10 false F65 2.917,1.083 3.208,1.26 0.292,0.177 10 false F64 0.104,0.063 0.458,0.271 0.354,0.208 10 false *a 0.667,1.74 1,1.917 0.333,0.177 10 false EW 2.385,0.438 2.677,0.615 0.292,0.177 10 false +1
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal F64-2 (+1) and a negative (-) lead to terminal F65-7 (EW).


ii.

Turn the wiper switch to the INT position.


iii.

Operate the intermittent wiper and check the voltage between terminals F64-2 (+1) and F65-7 (EW).

OK:

Voltage changes as shown in the illustration.


E136493E43
2.625,0.104 3.104,0.271 0.479,0.167 10 false FAST: 1.927,0.385 2.615,0.563 0.688,0.177 10 false 11 to 14 V 2.344,0.885 2.594,1.063 0.25,0.177 10 false 0 V 3.177,1.385 3.531,1.563 0.354,0.177 10 false Start 0.073,0.49 1.781,0.844 1.708,0.354 10 false Voltage between terminals F64-2 (+1) and F65-7 (EW): 0.771,1.375 1.854,1.552 1.083,0.177 10 false Wiper Operation: 3.354,1 4.542,1.198 1.188,0.198 10 false 1.6 +/- 1 second 5.792,1 7.021,1.198 1.229,0.198 10 false 10.7 +/- 5 seconds 2.729,1.385 3.083,1.563 0.354,0.177 10 false Stop 5.583,1.385 5.938,1.563 0.354,0.177 10 false Start 4.792,1.385 5.146,1.563 0.354,0.177 10 false Stop 4.438,0.104 4.979,0.302 0.542,0.198 10 false SLOW:

If the result is not as specified, replace the windshield wiper switch assembly.



d.

Check the front washer operation (for RHD).

i.
E239385C43
0.271,1.052 0.667,1.313 0.396,0.26 2.833,1.042 3.219,1.302 0.385,0.26 2.219,1.104 2.406,0.583 false 0.979,1.385 0.792,1.698 false 0.354,1.104 0.635,1.281 0.281,0.177 10 false F65 2.927,1.094 3.219,1.271 0.292,0.177 10 false F64 0.104,0.063 0.458,0.271 0.354,0.208 10 false *a 0.667,1.74 1,1.917 0.333,0.177 10 false EW 2.385,0.438 2.677,0.615 0.292,0.177 10 false +1
*a Component with harness connected
(Windshield Wiper Switch Assembly)


Connect a voltmeter positive (+) lead to terminal F64-2 (+1) and a negative (-) lead to terminal F65-7 (EW).


ii.

Turn the ignition switch to ON.


iii.

Turn the washer switch on and off, and check the voltage between terminals F64-2 (+1) and F65-7 (EW).

OK:

Voltage changes as shown in the following illustration.


E226602E43
4.104,1.323 4.021,1.521 false 4.74,1.333 4.865,1.51 false 0.979,0.885 2.719,1.24 1.74,0.354 10 false Voltage between terminals F64-2 (+1) and F65-7 (EW): 1.698,0.281 2.958,0.552 1.26,0.271 10 false Washer Switch: 2.604,1.531 4.354,1.771 1.75,0.24 10 false Approximately 0.5 seconds 4.708,1.531 6.708,1.729 2,0.198 10 false Approximately 2.2 seconds 2.948,0.823 3.708,1 0.76,0.177 10 false 11 to 14 V 3.365,1.167 3.74,1.313 0.375,0.146 10 false 0 V 3.292,0.479 3.688,0.635 0.396,0.156 10 false Off 3.354,0.188 3.729,0.365 0.375,0.177 10 false On

If the result is not as specified, replace the windshield wiper switch assembly.