Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH
RM3160E _59 Vehicle Exterior _019720 MIRROR (EXT) _0101077 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Memory)

a.

Check the mirror select switch and mirror surface adjust switch. (w/o Retract Mirror)

i.
B364151
1.76,1 1.76,0.333 1.76,0.333 2.042,0.333 false 0.583,4.229 1.083,3.583 false 1.677,4.24 1.833,3.583 false 1.01,4.24 1.458,3.583 false 1.344,4.24 1.667,3.583 false 1.969,4.229 2.042,3.583 false 2.25,4.24 2.25,3.594 false 2.688,4.229 2.625,3.583 false 0.177,0.156 0.49,0.354 0.313,0.198 10 false *b 2.094,0.219 2.406,0.417 0.313,0.198 10 false *a 0.51,4.25 0.823,4.427 0.313,0.177 10 false B 0.896,4.25 1.208,4.427 0.313,0.177 10 false HL 1.25,4.25 1.563,4.427 0.313,0.177 10 false VL 1.583,4.25 1.833,4.427 0.25,0.177 10 false HR 1.917,4.24 2.167,4.417 0.25,0.177 10 false VR 2.188,4.25 2.438,4.427 0.25,0.177 10 false M+ 2.667,4.24 2.917,4.417 0.25,0.177 10 false E
*a Mirror Select and Surface Adjust Switch
*b Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
12 (VL) - 15 (B)
9 (M+) - 7 (E)
Up Below 1 Ω
Off 10 kΩ or higher
12 (VL) - 7 (E)
9 (M+) - 15 (B)
Down Below 1 Ω
Off 10 kΩ or higher
13 (HL) - 15 (B)
9 (M+) - 7 (E)
Left Below 1 Ω
Off 10 kΩ or higher
13 (HL) - 7 (E)
9 (M+) - 15 (B)
Right Below 1 Ω
Off 10 kΩ or higher



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
10 (VR) - 15 (B)
9 (M+) - 7 (E)
Up Below 1 Ω
Off 10 kΩ or higher
10 (VR) - 7 (E)
9 (M+) - 15 (B)
Down Below 1 Ω
Off 10 kΩ or higher
11 (HR) - 15 (B)
9 (M+) - 7 (E)
Left Below 1 Ω
Off 10 kΩ or higher
11 (HR) - 7 (E)
9 (M+) - 15 (B)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror select switch and mirror surface adjust switch. (w/ Retract Mirror)

i.
B364153
2.031,0.979 2.031,0.281 2.031,0.281 2.219,0.281 false 0.5,4.083 1,3.583 false 0.948,4.094 1.396,3.583 false 1.25,4.083 1.583,3.583 false 1.583,4.083 1.771,3.583 false 1.917,4.083 1.979,3.583 false 2.167,4.083 2.167,3.583 false 2.604,4.083 2.563,3.583 false 2.281,0.177 2.594,0.333 0.313,0.156 10 false *a 0.229,0.271 0.542,0.427 0.313,0.156 10 false *b 0.792,4.115 1.104,4.271 0.313,0.156 10 false M+ 0.354,4.125 0.667,4.281 0.313,0.156 10 false E 1.115,4.146 1.427,4.302 0.313,0.156 10 false VR 1.5,4.146 1.813,4.302 0.313,0.156 10 false HR 1.833,4.146 2.146,4.302 0.313,0.156 10 false VL 2.104,4.146 2.417,4.302 0.313,0.156 10 false HL 2.604,4.146 2.917,4.302 0.313,0.156 10 false B
*a Mirror Select and Surface Adjust Switch
*b Component without harness connected
(Outer Mirror Switch Assembly)


Turn the mirror select switch to the L position.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for left side):
Tester Connection Condition Specified Condition
10 (VL) - 7 (B)
13 (M+) - 15 (E)
Up Below 1 Ω
Off 10 kΩ or higher
10 (VL) - 15 (E)
13 (M+) - 7 (B)
Down Below 1 Ω
Off 10 kΩ or higher
9 (HL) - 7 (B)
13 (M+) - 15 (E)
Left Below 1 Ω
Off 10 kΩ or higher
9 (HL) - 15 (E)
13 (M+) - 7 (B)
Right Below 1 Ω
Off 10 kΩ or higher



iii.

Turn the mirror select switch to the R position.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for right side):
Tester Connection Condition Specified Condition
12 (VR) - 7 (B)
13 (M+) - 15 (E)
Up Below 1 Ω
Off 10 kΩ or higher
12 (VR) - 15 (E)
13 (M+) - 7 (B)
Down Below 1 Ω
Off 10 kΩ or higher
11 (HR) - 7 (B)
13 (M+) - 15 (E)
Left Below 1 Ω
Off 10 kΩ or higher
11 (HR) - 15 (E)
13 (M+) - 7 (B)
Right Below 1 Ω
Off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



c.

Check the mirror retract switch. (w/ Retract Mirror)

i.
B364153
1.156,0.948 1.156,0.417 1.156,0.417 1.375,0.417 false 0.813,3.219 0.813,2.438 0.813,2.438 1.031,2.438 false 0.99,3.24 0.99,2.729 0.99,2.729 1.208,2.729 false 2.573,3.24 2.573,2.729 2.573,2.729 2.792,2.729 false 1.438,0.323 1.75,0.479 0.313,0.156 10 false *a 0.385,0.156 0.698,0.313 0.313,0.156 10 false *b 1.104,2.354 1.469,2.542 0.365,0.188 10 false E 1.271,2.646 1.625,2.813 0.354,0.167 10 false MF 2.854,2.656 3.208,2.823 0.354,0.167 10 false MR
*a Mirror Retract Switch
*b Component without harness connected
(Outer Mirror Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (MF) - 5 (E) AUTO position Below 1 Ω
Except AUTO position 10 kΩ or higher
2 (MR) - 5 (E) Retract position Below 1 Ω
Except retract position 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



Hide 84870A 2.INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Memory)

a.

Check the mirror select switch and mirror surface adjust switch. (w/o Retract Mirror)

i.
B364152
1.729,1.073 1.729,0.458 1.729,0.458 1.938,0.458 false 1.573,3.74 1.573,4.24 1.573,4.24 1.406,4.24 false 1.896,3.75 1.896,4.5 1.896,4.5 2.063,4.5 false 2.063,3.75 2.063,4.167 2.063,4.167 2.208,4.167 false 2,0.344 2.313,0.5 0.313,0.156 10 false *a 0.229,0.26 0.542,0.417 0.313,0.156 10 false *b 2.26,4.094 2.5,4.25 0.24,0.156 10 false E 2.104,4.417 2.51,4.615 0.406,0.198 10 false MSW 1.177,4.156 1.583,4.354 0.406,0.198 10 false M+
*a Mirror Select and Surface Adjust Switch
*b Component without harness connected
(Outer Mirror Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
15 (M+) - 12 (E) Mirror surface adjust switch pushed up 90 to 110 Ω
Mirror surface adjust switch pushed down 437 to 503 Ω
Mirror surface adjust switch pushed left 744 to 856 Ω
Mirror surface adjust switch pushed right 225 to 275 Ω
Mirror surface adjust switch not pushed 10 kΩ or higher
13 (MSW) - 12 (E) Mirror select switch turned to R position Below 1 Ω
Mirror select switch turned to L position 90 to 110 Ω
Mirror select switch off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



b.

Check the mirror select switch and mirror surface adjust switch. (w/ Retract Mirror)

i.
B364154
2.031,1.042 2.031,0.469 2.031,0.469 2.25,0.469 false 1.208,4.26 1.448,4.26 1.448,4.26 1.448,3.708 false 1.833,4.406 1.625,4.406 1.625,4.406 1.625,3.708 false 2.146,4.125 1.948,4.125 1.948,4.125 1.948,3.719 false 2.323,0.365 2.635,0.521 0.313,0.156 10 false *a 0.271,0.292 0.583,0.448 0.313,0.156 10 false *b 1.052,4.188 1.292,4.354 0.24,0.167 10 false E 1.906,4.313 2.313,4.521 0.406,0.208 10 false MSW 2.208,4.021 2.615,4.229 0.406,0.208 10 false M+
*a Mirror Select and Surface Adjust Switch
*b Component without harness connected
(Outer Mirror Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (M+) - 16 (E) Mirror surface adjust switch pushed up 90 to 110 Ω
Mirror surface adjust switch pushed down 437 to 503 Ω
Mirror surface adjust switch pushed left 744 to 856 Ω
Mirror surface adjust switch pushed right 225 to 275 Ω
Mirror surface adjust switch not pushed 10 kΩ or higher
15 (MSW) - 16 (E) Mirror select switch turned to R position Below 1 Ω
Mirror select switch turned to L position 90 to 110 Ω
Mirror select switch off 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.



c.

Check that the switch functions. (w/ Retract Mirror)

i.
B364154
1.167,1.01 1.167,0.333 1.167,0.333 1.375,0.333 false 0.729,4.115 1.146,4.115 1.146,4.115 1.146,3.698 false 1.479,4.125 1.313,4.125 1.313,4.125 1.313,3.708 false 2.438,4.146 2.271,4.146 2.271,4.146 2.271,3.729 false 1.438,0.24 1.75,0.396 0.313,0.156 10 false *a 0.24,0.198 0.552,0.354 0.313,0.156 10 false *b 0.594,4.042 0.99,4.365 0.396,0.323 10 false E 1.531,4.042 1.927,4.365 0.396,0.323 10 false MF 2.49,4.063 2.885,4.385 0.396,0.323 10 false MR
*a Mirror Retract Switch
*b Component without harness connected
(Outer Mirror Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
17 (MF) - 18 (E) AUTO position Below 1 Ω
Except AUTO position 10 kΩ or higher
11 (MR) - 18 (E) Retract position Below 1 Ω
Except retract position 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.