Home › Vehicle Interior › LIGHTING (INT) › BACK DOOR COURTESY SWITCH
RM3160E _58 Vehicle Interior _019707 LIGHTING (INT) _0103731 BACK DOOR COURTESY SWITCH G

LIGHTING (INT)  BACK DOOR COURTESY SWITCH  INSPECTION  


PROCEDURE

Hide 69350 1.INSPECT BACK DOOR LOCK ASSEMBLY (w/ Power Back Door System)

a.
E288040
1.042,4.198 1.865,3.823 false 2.188,3.833 2.656,3.948 false 0.167,0.104 0.479,0.302 0.313,0.198 10 false *a 2.479,1.604 2.719,1.802 0.24,0.198 10 false *b 0.969,0.323 1.271,0.521 0.302,0.198 10 false *d 2.031,0.771 2.865,0.99 0.833,0.219 10 false *c 2.708,3.885 3.167,4.083 0.458,0.198 10 false CTY 0.906,4.135 1.365,4.333 0.458,0.198 10 false E 0.646,0.365 0.948,0.563 0.302,0.198 10 false *e
*a Component without harness connected
(Back Door Lock Assembly)
*b Open-latch
*c Half-latch
*d Full-latch
*e Over-latch


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (CTY) - 4 (E) Open-latch Below 1 Ω
3 (CTY) - 4 (E) Half-latch Below 1 Ω
3 (CTY) - 4 (E) Full-latch 10 kΩ or higher
3 (CTY) - 4 (E) Over-latch 10 kΩ or higher


If the result is not as specified, replace the back door lock assembly.


Hide 69350 2.INSPECT BACK DOOR LOCK ASSEMBLY (w/o Power Back Door System)

a.
E287983
1.094,4.188 1.479,3.896 false 1.698,4.25 1.719,3.927 false 2.167,4.188 1.948,3.906 false 0.406,0.667 0.719,0.865 0.313,0.198 10 false *a 0.448,2.135 0.76,2.333 0.313,0.198 10 false *b 0.542,3.719 0.854,3.917 0.313,0.198 10 false *c 0.99,4.24 1.302,4.438 0.313,0.198 10 false D+ 1.552,4.323 1.969,4.552 0.417,0.229 10 false ACT+ 2.198,4.229 2.594,4.427 0.396,0.198 10 false ACT-
*a Lock
*b Unlock
*c Component without harness connected
(Back Door Lock Assembly)


Inspect the back door lock motor.

i.

Move the back door lock to the lock position.


ii.

Apply battery voltage to the back door lock motor and check the operation of the back door lock motor.

OK:
Measurement Condition Condition Specified Condition
Battery positive (+) → 2 (ACT+)
Battery negative (-) → 1 (ACT-)
Always Back door lock motor unlock operation


If the result is not as specified, replace the back door lock assembly.



b.

Inspect the back door courtesy light switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ACT+) - 3 (D+) Lock 10 kΩ or higher
2 (ACT+) - 3 (D+) Unlock Below 1 Ω


If the result is not as specified, replace the back door lock assembly.