Home › Engine / Hybrid System › 1AR-FE COOLING › COOLING FAN SYSTEM
RM3160E _51 Engine / Hybrid System _019676 1AR-FE COOLING _0105016 COOLING FAN SYSTEM J

1AR-FE COOLING  COOLING FAN SYSTEM  Cooling Fan Circuit  


DESCRIPTION

The ECM calculates an appropriate cooling fan speed based on the engine coolant temperature, air conditioning switch condition, refrigerant pressure, engine speed and vehicle speed, and sends the signals to the cooling fan ECU to regulate the cooling fans. The cooling fan ECU controls the cooling fan speed based on the duty ratio signal sent from the ECM. By basing its control on the operating conditions, the ECM can control the fan speed optimally using the cooling fan ECU, achieving both high cooling performance and quietness.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE ELECTRIC COOLING FAN)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Electric Cooling Fan.

Powertrain > Engine > Active Test
Tester Display
Control the Electric Cooling Fan
50004 234 16

e.

Check the operation of the cooling fans while operating them using the GTS.

OK:
GTS Operation Fan Operation
ON Cooling fans operate
OFF Cooling fans stop



Result:
Result Proceed to
OK A
NG (Cooling fans do not operate) B
NG (Cooling fans do not stop) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.CHECK COOLING FAN SYSTEM

C

11.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
2.CHECK COOLING FAN SYSTEM
a.

Disconnect the A43 ECM connector.


b.

Turn the ignition switch to ON.


c.

Check the operation of the cooling fans.

OK:

Cooling fans operate.



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT COOLING FAN MOTOR (COOLING FAN MOTOR AND NO. 2 COOLING FAN MOTOR)
3.INSPECT COOLING FAN MOTOR (COOLING FAN MOTOR AND NO. 2 COOLING FAN MOTOR)
a.

Inspect the cooling fan motor and No. 2 cooling fan motor.

Click hereEngine / Hybrid System>1AR-FE COOLING>COOLING FAN MOTOR>ON-VEHICLE INSPECTION


Result:
Result Proceed to
OK A
NG (Cooling fan motor) B
NG (No. 2 cooling fan motor) C



A

4.CHECK TERMINAL VOLTAGE (POWER SOURCE CIRCUIT)

B

C

REPLACE NO. 2 COOLING FAN MOTOR

4.CHECK TERMINAL VOLTAGE (POWER SOURCE CIRCUIT)
A268366C11
0.375,1.042 0.792,1.302 0.417,0.26 1.271,1.313 0.958,1.823 false 2.156,1.302 2.479,1.823 false 1.271,1.313 0.958,1.823 false 2.156,1.302 2.479,1.823 false 0.135,0.125 0.5,0.302 0.365,0.177 10 false *a 2.396,1.854 2.844,2.01 0.448,0.156 10 false +B1 0.854,1.854 1.354,2.01 0.5,0.156 10 false E1 0.5,1.104 0.865,1.313 0.365,0.208 10 false A5
*a Front view of wire harness connector
(to Cooling Fan ECU)


a.

Disconnect the A5 cooling fan ECU connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A5-3 (+B1) - A5-1 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)

NG

6.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
a.

Disconnect the A43 ECM connector.


b.

Disconnect the A5 cooling fan ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A43-44 (RFC) or A5-2 (SI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COOLING FAN ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (COOLING FAN ECU - BODY GROUND)
a.

Disconnect the A5 cooling fan ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A5-1 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT FAN NO. 1 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FAN NO. 1 RELAY
a.

Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 1 ENGINE ROOM RELAY BLOCK AND NO. 1 JUNCTION BLOCK ASSEMBLY (FAN NO. 1 RELAY)

NG

REPLACE FAN NO. 1 RELAY

8.INSPECT NO. 1 ENGINE ROOM RELAY BLOCK AND NO. 1 JUNCTION BLOCK ASSEMBLY (FAN NO. 1 RELAY)
A315951C01
0.24,0.521 0.552,0.719 0.313,0.198 10 false *2 0.125,0.094 0.438,0.292 0.313,0.198 10 false *1
*1 No. 1 engine room relay block and No. 1 junction block assembly
*2 FAN NO. 1 Relay


a.

Remove the FAN NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (FAN NO. 1 relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - COOLING FAN ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - FAN NO. 1 RELAY)

9.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - COOLING FAN ECU)
a.

Disconnect the A5 cooling fan ECU connector.


b.

Remove the FAN NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A5-3(+B1) - 5 (FAN NO. 1 relay) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A5-3 (+B1) or 5 (FAN NO. 1 relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (FAN NO. 1 RELAY - BODY GROUND)
a.

Remove the FAN NO. 1 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
2 (FAN NO. 1 relay) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (ECM - COOLING FAN ECU)
a.

Disconnect the A43 ECM connector.


b.

Disconnect the A5 cooling fan ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A43-44 (RFC) - A5-2 (SI) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (COOLING FAN MOTOR - BODY GROUND)
a.

Disconnect the z2 cooling fan motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
z2-1 (M-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - BODY GROUND)

NG

13.CHECK HARNESS AND CONNECTOR (NO. 2 COOLING FAN MOTOR - BODY GROUND)
a.

Disconnect the z1 No. 2 cooling fan motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
z1-1 (M-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPLACE NO. 2 COOLING FAN MOTOR