Home › Power Source / Network › 1AR-FE BATTERY / CHARGING › GENERATOR
RM3160E _57 Power Source / Network _019679 1AR-FE BATTERY / CHARGING _0105677 GENERATOR A

1AR-FE BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27416 1.REMOVE GENERATOR PULLEY CAP

a.
A194719

Using a screwdriver, remove the generator pulley cap.

NOTICE:

Do not reuse the generator pulley cap.



Hide 27415 2.REMOVE GENERATOR PULLEY WITH CLUTCH

a.

Secure the generator drive end frame in a vise between aluminum plates.


b.
A197237
1.51,1.938 1.198,1.938 1.198,1.938 1.01,1.427 true 1.542,1.021 1.635,1.542 1.635,1.542 1.875,1.542 true 1.74,0.177 1.958,0.177 1.958,0.177 2.198,0.594 true 3.01,1.583 3.01,0.927 true 1.594,1.844 2.094,2.052 0.5,0.208 10 true SST B 1.938,1.469 2.406,1.667 0.469,0.198 10 true SST A 1.583,0.094 1.896,0.25 0.313,0.156 10 false *a 2.823,1.635 3.292,1.833 0.469,0.198 10 true SST A
*a Rotor Shaft


Install SST (A) and (B) to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  


c.
A197239
2.229,0.823 2.719,0.823 false 1.948,0.563 2.115,0.25 2.115,0.25 2.24,0.25 false 0.958,1.865 1.438,1.865 false 2.281,0.167 2.802,0.365 0.521,0.198 10 false SST B 2.771,0.75 3.302,0.948 0.531,0.198 10 false SST A 0.813,1.76 1.063,1.979 0.25,0.219 10 false *a 1.813,1.792 2.063,2.01 0.25,0.219 10 false *b
*a Turn
*b Hold


Loosen the generator pulley with clutch by turning SST (B) as shown in the illustration.

NOTICE:
·

Check that the generator drive end frame is secured in the vise tightly.


·

Hold SST (A) tightly during the operation.




d.

Remove SST from the generator pulley with clutch.


e.

Remove the generator pulley with clutch from the rotor shaft.


f.

Remove the generator assembly from the vise.


Hide 27039 3.REMOVE GENERATOR REAR END COVER

a.

Place the generator assembly on the generator pulley with clutch.


b.
A192779

Remove the 3 nuts and generator rear end cover from the generator coil assembly.


Hide 4.REMOVE GENERATOR TERMINAL INSULATOR

a.
A192780

Remove the generator terminal insulator from the generator coil assembly.


Hide 27370 5.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A192781

Remove the 2 screws and generator brush holder assembly from the generator coil assembly.


Hide 27360 6.REMOVE GENERATOR COIL ASSEMBLY

a.
A192782

Remove the 4 bolts.


b.
A315801
0.344,0.896 0.573,0.896 0.573,0.896 0.698,1.219 false 2.615,0.26 2.833,0.156 2.833,0.156 2.969,0.156 false 1,0.26 1.229,0.26 1.229,0.26 1.51,0.802 false 3.031,0.063 3.333,0.292 0.302,0.229 10 false *a 0.167,0.802 0.479,0.958 0.313,0.156 10 false *b 0.708,0.188 1.167,0.385 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, remove the generator coil assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010)


Hide 27330 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A315469C01
0.844,0.427 1.458,0.427 false 0.677,0.354 0.99,0.51 0.313,0.156 10 false *1
*1 Washer


Remove the washer.


b.
A118367
0.646,0.375 0.979,0.375 0.979,0.375 1.208,0.74 false 0.438,0.313 0.75,0.469 0.313,0.156 10 false *1
*1 Generator Rotor Assembly


Remove the generator rotor assembly.


Hide 27310B 8.INSPECT GENERATOR DRIVE END FRAME BEARING

Hide 27310B 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A192787

Remove the 4 screws and retainer plate from the generator drive end frame.


b.
A192788
1.531,1.333 0.896,1.333 0.896,1.333 0.896,1.156 false 1.563,1.156 0.49,1.156 false 0.125,1.073 0.438,1.26 0.313,0.188 10 false SST

Using SST and a hammer, tap out the generator drive end frame bearing.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)